AutoCAD Civil 3D :: Code To Display Station Of Feature Line At Start Of Segment
Mar 13, 2012
I have a feature line, and a labels table created for it. The table has the following columns: Line or Curve #, Station, Segment Start X, Segment Start Y, Segment Start X, Bearing/Delta, Length, Radius, Grade Ahead.
what code I need for the table to display the station of the feature line at the start of the segment?
I also have an alignment with the same stationing over top of the feature line, but Im not sure how to code a reference text into the table either. I can create an end segment reference text for the plan view labels but even if I copy that code into the labels table it doesn't work.
View 4 Replies
ADVERTISEMENT
Nov 27, 2012
Is there a way to be able to choose a desired feature line when extracting from a corridor? For example, when subgrade and finished grade are on top of each other, it seems subgrade is always coming as default for extraction. I'm not getting the option to select the desired point code as usual for some reason. The best way I found is by turning off the subgrade feature line from the corridor properties, which is a bit tedious.
View 3 Replies
View Related
Feb 22, 2012
I can't seem to get my profile start and end station labels to appear even after I checked "Label start station" and "label end station" in the profile view properties.
View 2 Replies
View Related
Nov 26, 2012
I create a feature line including some arcs. While editing I need to redimension the feature line, but the arcs will lose tangency. Therefore I have to break/ trim/delete/manually edit the tangents until they intersect and then FILLET them to get a new arc. I tried EDIT CURVE with 0 Radius but it's not acceptable. Any workaround on this one (filleting feature lines like polylines or a closing option)?
View 2 Replies
View Related
Sep 24, 2012
is it possible to get the start and end station of each projected objects?
see picture. what i am doing is based on the different colour. they are geotechnical requirement for the minimul fill depth. so i am thinking about making a program to put in a profile for me and then put horizontal curves. so don't need to do anything by hand. good starting point at least. save a lot of time and not really hard to code either.
Civil 3D 2012
Work: Xeon W3503, 12GB, Quadro 2000, Dell P2211H x 2
Home: 3930k, 12GB, GTX 590, U3011, QX2710
View 2 Replies
View Related
Aug 31, 2012
I am working on road improvements, the City my client want to extend the improvement longer form the original scope of work. I am already completed the alignment and road profile centerline and the production plan is 100% completed.
What I need to do is to change and extend the alignment 750 feet backward from the original station (10+00). If I could explain correctly, I want to start the station @ 7+50 (backward from 10+00) and no changes on forward stationing.
What is the best way without doing re-creating alignment.
View 3 Replies
View Related
Mar 8, 2012
How and where can I adjust the station precision of the view frame start and end station. I am choosing snap to nearest foot station but I am getting 1+00.00. I would like 1+00 in the label. I am setting to start end to the layout name and mapping that to the current drawing field in SSM and do not have precision control there either.
Civil 3D 2012 & 2013
HP Z210 Workstation
Intel Xeon CPU E31240 @ 3.30 Hz
12 GB Ram
64 Bit Win7 OS
View 7 Replies
View Related
Oct 5, 2012
This is using Civil 3D 2012 Service Pack 2.1
When a Station Equation is added to an alignment it causes all of the profile views to get messed up. In addition once the EG profile changes the entire FG profile may also need to be changed. See this video I uploaded to Youtube that fully explains and shows the problem: [URL] ........
So, any way to some how lock the profile views start and end stations? Or to some how lock the PVI locations on a a proposed profile to certain stations?
View 2 Replies
View Related
Nov 13, 2013
We have recently started using a feature code library with our tremble survey gear and have been processing the linework and exporting the lines as a DWG and the points as a CSV and when iput them in the same DWG in Civil3D the point and Line Vertices are exactly on top of each other. Does any know how to fix this? I dont know if its to do with rounding, LSF, or projection to Cartesian?
View 1 Replies
View Related
Oct 2, 2012
Is there a way we can support a duel feature code ?In the field the surveyor would enter into his file “ EWD[*TB[“ .This code indicates the beginning of the “Edge of Woods” and “Top of Bank” .
Each shot after that would be along the edge of woods and top of bank . “EWD*TB” -- This code indicates shots taken along the “Edge of Woods” and “Top of Bank”
The surveyor would end this feature with “ EWD]*TB]“.This code indicates the ending of the “Edge of Woods” and “Top of Bank”
View 3 Replies
View Related
Oct 9, 2012
I have a subdivision plat that I'm working on with a curved lot line. When I label this particular lot line, Civil 3D labels it like it's two different segments. In other words, instead of labeling the line as a 100 foot long arc with a radius of 100 feet, it labels it as a 60 foot arc and a 40 foot arc. I can't figure out how to combine the two segments.
All of the lots lines were created from polyline objects, and there was no break in the original line work (nor is there any indication of a break in this location when I select it).
View 2 Replies
View Related
Nov 7, 2013
How do i get the feature lines in my corridor to change their style based on the code set style selected?Whats the point of defining featureline styles in the code set style if they don't change in the corridor? They only get used when you first create the corridor?
Is there something I am missing or is this the intended workflow?
View 9 Replies
View Related
Jul 3, 2012
I have a bunch of lines that are created with multiple segments. I'd like to annotate the total length. I can't figure out to do this without labelling each segment along the line using Line and Curve commands. How do I get one annotation that only shows the total of all the sements?
View 9 Replies
View Related
Jan 30, 2013
I am trying to create surface elevation labels along a polyline and I am having an issue with the label anchor point. I have created a line label style that uses a reference text to produce the elevation from a specified surface, however when I insert the label the default anchor point for the label is in the center of the line segment and that is where the reference text is taking the surface elevation. I am looking for the elevation of the surface at the start of each line segment, and I do not know how I can make it stop defaulting to the center of the line segment.
Attached is an overview of what my labels look like, where the anchor point is, and the layout properties within my label style. I am using C3D 2012.
View 9 Replies
View Related
Dec 27, 2012
My dragged state leader does not display properly. The attachment runs through my first line of text. My display is set to "As Composed" I do not want the stacked text setting.
View 9 Replies
View Related
Dec 11, 2012
I needed to remove a feature line that I used as a break line when creating a surface. When I removed the feature line from the definition of the surface, the grading did not change. It appears the points created by the feature line remain which is why grading didn't change. The only work around was to delete these points.
I noticed the same thing happens when I removed the surface boundary and inserted a new boundary. why these points remain and how to remove when I delete boundary and feature line from surface?
View 9 Replies
View Related
Dec 10, 2012
How do I modify the leader for station and offset labels to underline the top line of text?
View 3 Replies
View Related
Nov 29, 2012
I have a stationing line. I've used the block PTTICL to make ticks. The ticks display perfectly. I'll run through a plot preview and the ticks show on the plot preview. I push plot go to the printer and the ticks are not plotted.
I've checked the layer. They are on a layer that should print.
I've checked the block. The block is created on a layer that should print.
I've run through a number of options regarding the alignment label properties and found "display" to be equal to "true."
Everything else plots just fine. Only the station label ticks refuse to plot. My project is fairly short so the work around was to put a poly line right on top of the tick mark.
AutoCAD Civil 3D 2013.
View 5 Replies
View Related
Jan 31, 2013
Why do our feature lines all come in as the color white when xreffed into a drawing? Feature lines show up just fine in our topo drawing, so then we xref it into our design drawing and they all show as if the color is white when is is not in the layer properties. All other items (symbols, points, and lines) come in as the color they were drawn in the topo drawing.
View 3 Replies
View Related
Oct 24, 2012
The company I work for uses Illinois DOT linework Codes.They had been using Microstation. But the office Im in uses Civil 13. Any linework code set that I need to process field to finish?
View 1 Replies
View Related
Nov 27, 2012
Flow segment label using total Flow Type travel time for each segment:
C3D 2014 SP1
W7x64; i7 8gb; Radeon HD 5700
[URL]....
View 4 Replies
View Related
May 24, 2012
What to put in the override box to start a second line of text? its autocad 2013
View 2 Replies
View Related
Sep 26, 2013
Is there any way to project feature lines into a profile when the plan view is xref'd? I have my plan view "existing topo" with all existing features/Figures and a existing surface.
My profile is a separate dwg with plan view xref'd and surface a data shortcut. Of course there are feature lines and Survey Figures in the existing top I want to project into the profile, but can't because it is an xref. Besides copying .
View 1 Replies
View Related
Oct 31, 2013
C3D 2012. I am trying to get the distance from the start of a featrue line to a selected point. My object is "FLobj" and my Point is PT1. I am using the method Get2dDistanceAtPoint. This is the line of code.
(vlax-invoke-method FLObj 'Get2DDistanceAtPoint pt1 'pDistance)
I keep getting "too many actual parameters".
View 2 Replies
View Related
May 19, 2013
I am wanting to add the name of my feature line to a label style. I am trying to create a label style that will show Lot Number and Area. I know i can create parcels, but i dont want to! I have also created a map table that can do exactly what i want on polylines, but will not work on an xref. Labelling featurelines does work in xrefs.
how to add the name into a label style?
View 4 Replies
View Related
Jul 11, 2007
Is there a way to decurve feature lines like how we do it with polylines? I am labeling my feature lines but don't want the curve labels to show up
View 6 Replies
View Related
Jan 7, 2014
I am building a surface and have back of curb, curb face, and curb flowline going around a curve. I cannot create the lines with the usual pline as they will cross due to poor field collect. I created the curbs with multiple arcs. I was then going to change them into Feature Lines and am wondering if I can then use them as breaklines in a surface.
View 1 Replies
View Related
Mar 1, 2013
I have a roadway alignment with FG profile and I want to place a feature line on the roadway centerline that represents the FG profile elevations.
View 7 Replies
View Related
Apr 11, 2012
We have cooridors with features such as terrace drains and flowlines, but we cant seem to get the linetypes to show up correctly. For example a flow line should have arrows but it shows up without the linetype and looks continuous.
LTSCALE =1
MSLTSCALE=1
PSTSCALE=1
DRAWING SETTINGS - 1"=40'
CIVIL 3D 2012
View 3 Replies
View Related
Jan 7, 2014
I am building a corridor with the right side of the pavement fitting to the existing surface.The subassembly used to link the edge of pavement to the existing ground is LinkSlopeToSurface.
On the corridor created, the feature line (code P2) of the corridor surface (top) starts from the station 0+025, instead of 0+000.
I was wondering why there is no feature line P2 for station range 0+000 to 0+025? Does that mean the linkage to the existing ground surface not exist for the slope defined in the subassembly?
View 2 Replies
View Related
Mar 25, 2013
We are running Civil3d 2012. When converting a line or 3d poly to feature line, or just creating one it adds elevation points where it crosses surface breaklines even if you do not assign elevations. We want the feature to just have 2 elevations. The beginning and end. Is this a bug? Or is there another setting somewhere?
View 7 Replies
View Related
