I create a feature line including some arcs. While editing I need to redimension the feature line, but the arcs will lose tangency. Therefore I have to break/ trim/delete/manually edit the tangents until they intersect and then FILLET them to get a new arc. I tried EDIT CURVE with 0 Radius but it's not acceptable. Any workaround on this one (filleting feature lines like polylines or a closing option)?
View 2 RepliesI have a feature line, and a labels table created for it. The table has the following columns: Line or Curve #, Station, Segment Start X, Segment Start Y, Segment Start X, Bearing/Delta, Length, Radius, Grade Ahead.
what code I need for the table to display the station of the feature line at the start of the segment?
I also have an alignment with the same stationing over top of the feature line, but Im not sure how to code a reference text into the table either. I can create an end segment reference text for the plan view labels but even if I copy that code into the labels table it doesn't work.
So here's an odd one (at least I think it's odd ): I have a drawing that it utilizing feature lines which are projected to the cross sections to display R.O.W., easements, etc. However, every now and then (there doesn't appear to be any similar operation that causes this) the feature lines will change their location, in this case they typically seem to move north and east about 200'. I can't deuplicate the problem...it just seems to happen on its own.
I'm running Civil 3D 2013 with SP 2.
I have created a feature line from a survey which will be the inside shld of my new road design. I have created the feature line using my design elevations but need to add a PI and Elevation at a specific Northing. When I try to edit I can only seem to find the chainage and elevation but I also need to know the northings and eastings so I know where to insert my PI. I would like to just edit the table since I can't seem to figure out how to insert the PI. (I am new to C3D and still learning...) My final product will be a road with 2% crossfall and I intend to use offeset and grading features to accomplish my final design. How I make this edit...
View 1 Replies View RelatedI'm currently using the Autocad Civil 3D 2014 on daily basis for urban infrastructure design. When using Autocad Civil 3D 2013, I always would create feature lines from corridors and then export this file to a ACAD 2007 version, which would read the feature lines as 3D polys. The company's topographer could then use this file to make his markings on the field very easily.
Now, when I do the same process using Autocad Civil 3D 2014, the ACAD 2007 file won't present the feature lines as 3D polys, but as 2D polys. This presents a major inconvenient, because I now have to export the file to ACAD 2007, open it in Autocad Civil 3D 2013, rebuild the surface from the design contours and create a feature line from the design surface; export the surface AGAIN to ACAD 2007 and FINALLY I'll get the 3D poly my topographer can read.
I have a curb return that was drawn as a fillet and I added two points at the PC and PT. Is there a way to create a feature line out of this with the two points associated so that it will interperlate between those 2 points?
View 1 Replies View RelatedOver the past 6 months we have had the feature lines just up and disappear from the drawing for no reason. They were not erased. They just went away for some reason but the surface created from them was still there.
View 9 Replies View RelatedI am new to civil 3d. I am building a site down the side of a mountain which consists of 4 tiers/ pads with different levels. Each of the 4 pads has its own feature line. To prevent any confusion or attractions of the feature lines to each other i have moved them to a site that i created called temp site locations.
What is the best way and location to do each of these gradings and how do i tie them all back on to the same drawing ? I assume (maybe wrongly) to do each separately and copy back into the the real drawing.
Do i need to create a new site for each pad. If i do my grading in the temporary site when i bring them back to the real site will the interact with the other feature lines.
I have a created a surface from contour lines.I have drawn a feature line and assigned elevations (it slopes down from 3.5m elevation to 2m elevation). I have added grading from the feature line to the existing surface but have not merged the feature line with the surface.
I also have to make a low area (elevation at 1.5m) on the surface and know i need to grade at 1:1 from the feature line to the low point. Is there a way to grade from a feature line at a given grade (1:1) to a known height (my low point at 1.5m) without drawing another feature line for my low point? Seeing as the height of the feature line varies I can't just offset it at the grade.. I.e. the grade is the constant here.
I will have a few walls and lower / higher areas to grade to. I have drawn the top of my wall and mounds and have assigned them elevations but not sure whether to now make them all feature lines and try to merge with the surface by grading at a set grade or to do some sort of infill.
Can you delete part of a fillet feature? While still keeping part of it & adding to it.
I have a fillet feature with 2 fillets to a part. One is in the wrong place.The Feature Fillett1 if you edit it, you will see what I mean.
Keep the middle one. Both fillets are 0.25" / Replace the bottom fillet to the top corner.
I would like to keep the Feature in the order it is in, if possible.
I am using Inventor 2012.
Is there a way to link feature lines to points? If I have a series of points and I've joined them with a feature line; I want the feature line to update automatically if I adjust a point elevation.
View 4 Replies View RelatedI want to hide feature lines in realistic view. I changed corridor's feature lines style as pic1 but i can still see feature lines (pic2).
View 1 Replies View RelatedI am using the Mill&Overlay sub set to overlay an semetrical road and a crown offset of zero. I one file the crown point feature line has gaps in it and in another file it zig zags along the road.
I forgot to mention that the triangles and the cross section look as expected. trouble is I want the crown profile
Civil 3D 2012 & 2013
HP Z210 Workstation
Intel Xeon CPU E31240 @ 3.30 Hz
12 GB Ram
64 Bit Win7 OS
I've had cause to do some site grading by creating featurelines from scratch. What is the difference between gradient and slope (they are the same are they not?) when creating them as I always seem to go wrong when using this method??
IDSP Premium 2014 (mainly Civil 3D 2014 UKIE SP1 & Infraworks with some limited 3ds Max Design)
Win 7 Pro x64, 256Gb SSD, 300Gb 15,000 rpm HDD
16Gb Ram Intel Xeon CPU E5-1607 0 @ 3.00GHz (4 CPUs), ~3.0GHz
NVIDIA Quadro 4000, Dual 27" Monitor, Dell T3600
I would like to export feature lines out as land xml file. Can this be done in Civil 3D or is there another work around.
View 5 Replies View RelatedI brought a site into a drawing by LandXML which had 35 feature lines in it. How do you get the actual linework of the feature lines to show up in your drawing? It shows them in the site but the linework is not there.
View 1 Replies View RelatedI want to do this: URL...to get vertex of feature lines.However, I have to select a Reference:Autodesk.AECC.Interop.Land
Can I use that Reference for Civil 3D 2014? is there limitations for Interop in Civil 3D to feature lines?
I use(agreate) all these References Autodesk. AEC.Interop. BaseAutodesk. AEC.Interop. UiBaseAutodesk. AutoCAD. InteropAutodesk. AutoCAD. Interop. CommonAutodesk.AECC.Interop.<domain>Autodesk.AECC.Interop.Ui<domain>
I would like to add elevation values of start and end of feature line segments within a table. I can set up start and end co-ords but can't seem to find where I can add the levels?
I can add lables to the plan with levels but really would like to have a table as well as some of the segments are too small to lable on the layout.
I have a road corridor with feature lines connecting the road edges (cyan), ditchline (dark green), daylight_cut (yellow), daylight_fill (green) and daylight (white). At certain random locations along this corridor I am getting feature lines which span from one station to another, ignoring all of the corridor sections in between. The image below shows a daylight_fill line spanning over 60m, even though there is a daylight line through this region.
In this area a ditch line and a daylight_cut start at 4+110, skip over the next cut section at 4+120 and jump over a hundred meters to the next piece of ditch at 4+280..This corridor builds clean - no error messages reported.
I have several featurelines that I wish to explode to be 3D Polylines (bad, I know, but it's a test for a way to get data across from our design group to our survey group).
Last week, in this drawing, I exploded a large selection of featurelines and they all became 3D polylines, preserving their elevation data. This week, I drew an additional set of featurelines in the same drawing. When I explode them once, they lose all elevation data, becoming lpolylines at z=0. Additionally, the Prospector shows me several errors: "breaklines not added to surface" or something similar. Which is an odd result for the explode command.
Why did this work once but not a second time?
Win 7E 64-bit, Intel i7, 12 GB C3D 2012
I have reason stumbled across the offset assembly functionality of corridors, and for the most part, I have been quite impressed. One thing that has come up that is odd to me that when I create a surface from the corridor using feature lines, the feature lines that are created by the offset assembly are not added to the corridor surface, even though they are visible and can be selected. When I create the corridor using links, everything is fine and the surface looks great. I can work using the links, but the more curious part of my nature is a bit tortured not knowing why this is happening.
On a related note, any strong preferences/reasons for using links vs. feature lines, or vice versa?
C3D 2014, SP1
Dell Precision T3500, Windows 7 64-bit
Is this the only way to extract feature lines from a corridor i.e. selecting each one - it gets a bit tedious.
Is there any method to select a corridor and extract all the feature lines that are set to display?? I think third party software (Sincpac?) can do this but this is not an option for me and I am not well versed enough in .NET to write something to achieve this myself.
No feature lines in offset corridor
View 3 Replies View RelatedIf the 2D layout is updated I need to move featurelines and gradings to the new locations without changing their Z values. It seems OSNAPZ is supposed to serve this purpose but it's not working for me. I have OSNAPZ=1 and ELEV=0 but when I snap a featureline vertex to the 2D linework the vertex ends up at elevation zero. How do I make this work?
Infrastructure Suite/C3D 2013, LDT 2004, Power Civil v8i SS1
WIN 7 64 PRO
HP Pavillion h8xt, i7 2600, 12 GB
RADEON 6450, 1 GB
Flow segment label using total Flow Type travel time for each segment:
C3D 2014 SP1
W7x64; i7 8gb; Radeon HD 5700
[URL]....
How do I make my corridor feature lines to change color? I want daylight cut to be red and daylight fill to be green.I've checked under "Toolspace/Settings/General/Multipurpose styles/Feature line styles/Corridor daylight line - Cut" but it doesn't work.
View 4 Replies View RelatedI have this problem when creating grading groups with more than one feature line in them. It seems really unstable when you trying get the grading to connect. I have tried to create two separate grading groups in one site or two feature lines in one grading group. And the result is the same, the grading that will be create can sometimes look oki, but suddenly they tend to disappear or look weird...
View 4 Replies View RelatedI created a few different Sites as I created Feature lines in order to keep them separate and avoid having one affect the others. The problem is that I am now stuck in the Last Site created. So commands like "QUICKEDITFEATUREELEVS" only see those feature lines in the last Site created. How can I switch to another site so I can quickly edit those feature lines?
View 3 Replies View RelatedImagine I have a standard naming convention for my assemblies elements Sometimes I want to show some feature lines and sometimes other.
Can I define a "style" for this ?
Civil 3D (2013)
Move multiple feature lines between sites?
Is there a way to move all the feature lines in a surface from one site to another site all at once? I know how to do them one at a time, but when I select them all, right-click "move to site...", it does nothing.
Windows 7-64
8GB RAM
AutoCAD Civil 3D 2013
I have a low pressure sewer system that runs along a road side but is not always parallel to the road. I'm using hte centerline of the road for my alignment. What I need to do is have a profile of the existing ground above the centerline of the pressure pipes show in the plan/profile sheets. I do not need a profile of the roadway.
I'm currently using feature lines to accomplish this and that works fine in the main drawing, however, the profiles I create there don't transfer to the plan/profile sheets when I create them. The only way I have found so far to get thoe profiles to show in the plan/profile sheets is to create the feature lines in the plan/profile drawing and project those lines to my profile view. This is a fairly large system so I will have numerous plan/profile sheets. Creating the feature lines and profiles in the individual sheets is fairly time consuming.
I'm currently using Civil 3D 2012. I realize that with the addition of pressure pipe networks in 2013 might very well give me the tools I need but I'm at a point in this project, and our office, where switching to 2013 isn't really an option yet. However, if that is my answer then I will have to consider that.