Is there a way to add/remove vertices from polylines using the grips method similar to editing hatch boundaries? I know of "Pedit" and "edit vertex" then "add vertex" but this seems like too many steps after working with hatch boundaries.
View 2 Replieswhe i try to draw a pline it accepts the first numerical entry but locks up on the second point. Also when i use this command no matter what layer it is on the line becomes very fat
autoCAD architecture 2013
I am trying to use a pline to create an open ended wall. When I try to 'calculate automatically' by selecting a pline the width of the wall (2 components 8" wide total) the dialogue comes up and asks which component I want to apply the endcap to. I want to apply it to both, but don't seem to have that option.
View 2 Replies View RelatedI am using AutoCAD Architecture 2012 and on multiple projects I have been working on I have been having objects randomly move when I rotate my view. The strange thing is that the grips still show up where the object is supposed to be. Below is a screen shot to explain what I am talking about.
View 8 Replies View RelatedI quite often like to use the wall grips to adjust the length of a wall. This works really well accept for the occasional situation were I want to snap to the face of another wall rather than the justification line. I know that I can snap to the face of a wall rather than the justification line because I have some files that it works fine in and other files that it does not work in.
View 2 Replies View RelatedAfter upgrading ACA2012 to Autodesk Building Design Suite (which still includes ACA20012)
The grips on images to resize them to a rectangle for example no longer appear.
The grips still appear on other entities such as lines, circles and rectangle still appear.
Driving me potty as it still works on the systems where this upgrade hasn’t been applied yet.
It’s not drawing specific as this happens on all previous drawings opened on the upgraded machines, but not on the none upgraded.
Using the scale function to reference points at the moment as a very much longer work around, but would like it back the way it was.
I have LWPOLYLINEs that represent a cross section of a train tunnel. Each LWPOLYLINE lists its 2D points in an Object Coordinate System.My task is to create 3D Polylines in WorldCoordinateSystem using those LWPOLYLINEs.I have posted a drawing with sample objects.
I have attached a sample drawing. Drawing was created with Civil 3D 2013, but I exporttoautocadr12dxf'd it and then save to 2004 dwg so most should be able to open it.
Just upgraded from 2012 to 2013.....Why did they change the way you stretch a wall with grips???? Now, I cannot align a wall perpendicular to the inside of another wall, only the outside edge/face....Is there a fix or setting I am not aware of?
View 1 Replies View RelatedACA2011
So... Is it possible when drawing a line to snap to a 'grip'? I've got a drawing that has been converted from PDF to DWG and the wall outlines are gone. What is there is hatching that is the poche. That means I could re-trace the walls if I could snap to the outside grips of the solid hatching that is there.
In 2010, when you did a multileader, on the landing you had an arrow grip on both ends and then the box grip in the middle.. Now in 2012 they have the landing set to where there is an arrow grip at one end closest to the text and the box grip at the other end....
Is there any way to set the multileader grips on the landing in 2012 the way they were set up in 2010?
How to use wildcards to aid in replacing text. i have a series of drawings with a few hundred door tags that I need to add an alpha character to the end. I'm on ACA 2008.
example - change door number 1200 to 1200A, 1203 to 1203A, etc.
I was using the 'Isolate Objects in Plan' on my Model when I experienced a fatal error, and my system went down. So I went to my latest Autosave and opened it back up, only lost 5 minutes at the most. No, big deal, right?
But now I have objects missing, and when I go to save it says...
..."Save command is not allowed when edit in view session is active"...
It must still be in Edit in view, the only problem is that the small dialog box which takes me out of edit in view is missing. So, how am I supposed to exit this session? I have nothing active in the ribbon, nothing in the tabs a the bottom of the screen.
When I try edit block in place this error occurred:
Errors found in references to other objects:
Object reference missing: AcDbXrecord, to AcDbBlockTableRecord
Cancel
ACA 2011
So, I extract elevations from my model. No prob. Works perfectly. I then often edit linework to change some linework colors...works fine. However, What if I want to change/edit a Hatch? When I click on 'Edit Linework', the hatch automatically turns off to allow me to edit the linework... Can one edit the Hatching?
Is there any easy way to globally edit lineweights of certain components? Several of the components look fantastic at one scale and terrible at another. Some we just need to lighten but I cannot find where to edit them. I can always (of course) edit the block once it is inserted or edit layers in each drawing but would prefer a more permanent solution.
View 1 Replies View RelatedI created my own tools of own content on my own pallets and then found . you can drag a whole tab into the browser to quickly archive your tools. Having reinstalled I have 'dropped the collections back to ACA12 and all my tools restored.
However I can no longer edit or add to these tool pallets. I cannot edit any properties within tools either. There is no lock symbol on the pallet that I can see, only a refresh symbol.
The .atc file they reference (found from the Content Browser location they came from) is not set to read only. Permissions seem to be set to allow read, modify, write etc. I first used the 'My Tool Catalog' provided but also copied it all back to a new catalog but it's still locked.
I am running Architecture 2014 (PrDS-U) on a Windows8 Pro N.
In Architecture I am a frequent user of the Project Navigator.
After moving to W8, I find that I can not edit Project properties, neither from Project Browser nor the Navigator.
The project resides on my local C:VCC and the folder is being shared on my network. It is not write protected. Everyone has full access.
Others who are connected to the share can edit the project, they are running Windows 7. I cannot.
I'm getting very long run times to edit x refs in place. Once the exref drawing opens, sometimes after 2 or three minutes, and I make my edit, It can take ten minuted to close the xref.
Drawing are clean, purged, -purged, recovered audited. Computer is new workstation and dedicated to CAD only. Very little opportunity for corrupted files.
in 2000 I was able to discover a command that allowed you to renumber a large selection of blocks in order. I have been searching for that command again every time I need to renumber a floor plan due to the addition of new spaces. What this command was and if it is still available in 2010? It would save a ton of time!
View 2 Replies View RelatedThe way it looks I should be able to edit the propertyset data though an XRef... but all the properties are grayed out. I thought it was because I also had the XRef open... so I closed it. Still the same result.
The discription says "Edit property set data in the current drawing or through external references. Add or Remove property sets."
Am I not understanding the tool - or what?
We have an intern that has somehow made it impossible for her to edit inside viewports(switching to model space) on her layouts. None of us has seen this before and do not know how to reverse what she has done. This happens with any drawing she opens. She can edit when in the model space tab, but when she goes to one of the layout tabs and double clicks on the viewport she cannot edit. The viewports are not locked.
We have had several people look at it and cannot find what command or setting she changed. She does not have admin rights so I do not think she could have run a script. She is not familiar with AutoCAD Architecture, her experience has been limited to Revit.
For some reason I can't edit the "Position Z" when I created a 3D object via extrusion. How can I do this?
View 2 Replies View RelatedI am having trouble trying to edit the title fonts in a door schedule. No matter which font I pick under "Edit Schedule Table Style" after a selection of the schedule and right clik, the title font will not change. The listed doors font does change. Is it not poosible to change the title and descriptor font?
View 1 Replies View RelatedI can edit the cleanup in place just fine and in plan all is good, but in 3D, the height of the modfied region is not the full wall height, just some random height.
View 4 Replies View RelatedI recently loaded AutoCAD Architecture 2008 and the menu tabs for File, Edit, Window etc were all missing. They are replaced with a tab that says M-Color 9.5. When i load the program with older files (from this morning) the menu tabs are there but then they disappear. How do i get them back?
Also in addition to that my toolbars are gone, but i can recover those when i have my tool bars.
there is a command that allows for editing the actual line work in an object controlled by the Display System... it is a last resort command if you cannot get the object to display as you wish.What is it?
View 1 Replies View RelatedSeems like Multi-View Blocks are like that hot red-head in high school that you really want to get to know until you get to know them.
I made a bunch of blocks for my electrical plans. Annotative symbols for plan view, 3D blocks for model view, and elevation blocks for elevations. I then started creating the MVBs.
Upon insertion the annotative blocks appear super small and the model view blocks scale way up. The model view blocks are not annotative and are not supposed to scale at all. It seems MVBs see any block inside that is annotative as an indication that the entire MVB shall be annotative. Fustrated, I finally found a work-around that is a bit half-arsed:
I made another block as a sort of holder for the annotative symbols that was set to not be annotative and inserted that into the MVB. VOILA! the MVB itself doesn't scale, but the annotative symbol inside the non-annotative block does. This works fine except for one caveat: I can't edit attributes that are in blocks inside of blocks. If I made another block to use in the MVB for the attributes, it would work, so long as I don't make it annotative, which isn't what I want.
So, A) is there a better work-around than the block-in-a-block-in-a-multi-view-block method, or B) Is there a way to access and edit attribute data of sub-blocks inside a MVB?
Maybe my next thread will be about red-headed Multi-View Blocks with carpets that match the drapes.
Edit: Running ACA 2009
I have terrible lag whenever I am drawing a polyline. It seems like it is taking forever to render the preview of the line when I am dragging the line across the screen. I would prefer to just turn off the line preview if at all possible. So far, I have not been able to find a way to do this. When I say preview of the line, I am talking about the transparent line that follows your cursor after you start a polyline and exists until you click to place the line where you want it.
I am running Windows 7 Pro 64-bit
Dell Precision M6600
8-gb ram
NVIDIA® Quadro® FX 2800M graphics
Recieved a ACAD converted Microstation File for use in an upcoming construction project. Would like to convert all of the existing ellipses to polylines. Have read several threads that lead me to believe redrawing them is about the only real way to do it. Posting here in hopes of a solution. Drawing contains 127 ellipses, and I dont want to redraw all of them!!
Currently on C3D2012.
what I need to do is to flatten a spline into a pline because I need to measure its diameter.
I know how to it with a 2d spline but how can I manage in case I have a 3d one?
I'm using AutoCAD 2013 and it will not convert a p-line to revcloud .
View 9 Replies View Related