I am trying to insert a block into a file in Acad 2014 and it comes in too large. If I insert the same block into the same file using Acad 2012 it comes in at the correct scale. Doesn't seem to matter if insunits is 0 or 1, or insunitsdefsource or insunitsdeftarget are also 0 or 1.
There must be some variable or variables I'm missing.
I am having an issue inserting a detail call out "block". The blocks were created to be annotative however, when I am inserting them into my paperspace at 1" = 30' it shrinks up the block. In model space it shows at the correct size.
View 2 Replies View RelatedI downloaded a block of a plan view of a wheelchair user so I can see just how much space there is available.
The block is dimensioned but when I insert it and measure its dimensions, the readings are different. For example, a dimension reads 1070mm but when I measure it, I get 1023mm. Not far out but when I measure a 150mm dimension, I get 83mm. A 460mm dimension is measured as 536mm.
INSUNITS = 0
I've got a question about plotting to a measurable PDF with the correct scale.
Currently, if you plot to PDF (ARCH full bleed D 24x36 paper size) using 1:1 scale of the Layout area (including viewport, title block, etc) you get a nice PDF of the appropriate plan which would print to paper at the correct scale (1/16" = 1' 0'). If you set the plot scale to 1/16" = 1' 0' then preview/plot it then it appears completely tiny (like 2% of the page size), in the bottom left corner.
However, I want to make the PDF measurable. At the moment, if you do this using a 1:1 plot, the default numbers given by the measure tool are way out of proportion (a 29' dimension in the drawing is measured as 48,294 with no units). To get it to give accurate measurements, you have to tell Reader/Acrobat to ignore document scaling in preferences, then "Change Scale Ratio" to the appropriate scale ratio (0.625 in = 1 ft). This means you can measure to scale in Reader or Acrobat BUT these options disappear once you close Reader/Acrobat.
creating measurable PDFs from Autocad plots?
I exported a DWG from sketchup, for version AutoCAD 2010.
When i open it in my office with 2014 the scale is correct. But when i send it to a colleague with verion 2010 the scale is different.
Is it possible to insert a scale bar? I have searched all over but the only instruction I got was to click insert scale bar in the annotation pallette, but no such thing exists. Surely this should be easy enough?
View 9 Replies View RelatedCan I scale up a 100+ blocks at once and have each base point as the blocks insert point?
View 9 Replies View RelatedI am working with surveying points and what I used to do was insert the dxf file containing the points to my drawing and they would be inserted with their correct scale. However, now in AutoCAD 2013, when I insert them they are in a different scale and I must adjust them. Is there anyway to have their original scale carry over in 2013?
View 4 Replies View RelatedI am currently using Autocad 2014 and I am attempting to insert a dynamic block from a tool palette. I would like to click on a dynamic block in the tool palette and have it prompt for the (uniform) scale. It seems simple enough but either all the dynamic properties are lost or it is inserted at 1"x1" (the scale of my original block). How to get this to work?
View 3 Replies View RelatedI have just updated to Autocad 2013. While working on existing drawings (previously created in V2012), I am having issues with the SCALE command. Most times, but not always, when I add a line or block, with a base point on an existing line or object and try to scale it, I get an "extremely small scale factor ignored" message, although I did not get a chance to enter a scale factor. While it appears most times, but not always, if I draw a new line in empty space on that same drawing, I am able to use the SCALE command without problems. I also have the same issue when trying to scale an existing line or block, most times but not always.
Here is a copy of the command line while I am trying to make it work:
Command: l
LINE
Specify first point:
Specify next point or [Undo]: 100
Specify next point or [Undo]:
Command: sc
SCALE
Select objects: 1 found
Select objects:
Specify base point:
Specify scale factor or [Copy/Reference]:
Extremely small scale factor ignored.
Command:
SCALE
Select objects: Specify opposite corner: 1 found
Select objects: Specify opposite corner: 1 found, 2 total
Select objects:
Specify base point:
Specify scale factor or [Copy/Reference]:
Extremely small scale factor ignored.
If you notice, it does not give me the chance to enter a scale factor. As soon as I pick the base point, it skips over to the error message, yet displays the scale factor prompt with a blank factor. I'm experiencing this issue on various files (not all but most), so I don't think it is a corrupt file. Why I get this and if I can correct it?
When I open a new drawing in my AutoCAD 2013 that I just recently installed last week, I encounter a problem that I am not familiar with from previus versions of AutoCAD I have worked on. First of all, the units default to decimal, and I want them to default to architectural, with feet and inches. I have to type UNITS in the command line every time I open a new drawing in order to adjust this. I have AutoCAD for Architecture 2012 on another computer, and the program automatically defaults to architectural units upon opening up. Just to let you know, the program I am having this difficulty with is part of a package called Autodesk Building Design Suite 2013. I was under the impression that it included AutoCAd for Architecture, but I think it has only standard AutoCAD.
The scale of the objects I draw vs. the scale of the drawing field is very out of proportion. What I mean is, when I open a new drawing and draw a 30' -0" line, the line appears so long on the screen that I cannot see the whole object, even if I zoom out to the maximum. I should be able to see the object in it's entirety. In fact, when I draw a line that is only 12" long, even when the zoom is all the way out, the line looks huge in length. I have tried adjusting the units to the architectural/inches setting of course, and I have tried adjusting the scale in model space from 1:1 to 1/4'=1'-0", but nothing is working.
I have a block that i would like to scale based on the plot scale when plotting.
We set up our drawings full size and occasionally we want to plot them at half size. We do this by setting the plot scale to 1:2 (custom) in the plotting dialog. We have a few blocks that we want to print at the same size on paper, essentially become twice as big.
Is there is a way to fix the size or just set a few scale states and have them automatically adjust based on the plot scale (not drawing/annotative scale)?
AutoCAD 2013 2D - when scrolling the viewport scale list, the viewport zooms with each scale instantly.
View 1 Replies View RelatedIm trying to keep annotative blocks in the same spot on different scale viewports. The main issue Im having is, when i have a lets say house plan in viewport #1 and have all my blocks in place that I moved copyed from my template. When I open another viewport at a diffrent scale the blocks move. Im useing a large number of blocks for electrical symbols we use at work that I need to be in every viewport so we can copy them and place them where needed on the plan.
View 3 Replies View RelatedI have trouble figuring out dash lines. If i change global scale factor or current object scale in a spedific paper space,
the other page will be affected...
I am putting together a catalog with some drawings from AC 2010. I am drawing in model space and printing in paper space. The view port scale is 1:1. If I print directly from Autocad to the printer, everything is fine. If I first plot to PDF from Autocad and then print, the dimensions are off by about 1/8". The dimensions read correctly, but they do not measure correctly. The paper size is 8 1/2 x 11. I would like these PDF files to be accurate in case someone needs to print them.
I have tried saving to dwf and then printing and printing out of Design Review but it doesn't make any difference. My settings in Adobe are 1:1 as far as I can tell.
I'm trying to convert a hand drawn paper plan of our house into Autocad so that I can tweak it. I'm not bad at drawing things in autocad, but how to set it up properly for the file to be printed out in a shop on A0 at the correct scale. Either some info on how to set it up, or a template file that is already setup would be great.
View 9 Replies View RelatedI have a drawing and when I measure the width of a window it says 30.9, when it is supposed to be 1100mm. Is it possible to change the scale so that the measurement is correct?
View 8 Replies View RelatedI have downloaded JPG2000 files from the National Map. I can insert the image, but it doesn't recognize where it is supposed to be.
[URL]......
I'm using Civil 3D, 2013 on a 32 bit machine.
I have the DWG file with a row of parts. I need to take each part geometry and insert in separate IPT sketch.
As result in the IPT I have multiplied for 25.4 geometry.
IN this drawing, I want the 9.00 to be either 4 ( feet) or 48 (inches).
How do I set the correct scale in this or any drawing?
So I create a block on layer 0 and then create the block as a 1 inch by 1 inch block so it is easy to scale up to the size I need but when I try to insert the block at the scale I need it wont resize it to the correct scale. It stays at the 1 inch by 1 inch original block.
View 1 Replies View RelatedWe had a lab we have a CAD class in. One student suddenly has an issue where AutoCad LT 2014 freezes when he opens up his project and changes the scale. He has tried several computers and the same issue occurs. It seems like it may be something with the project file. Is there any way to retore the file where this does not happen and so he can continue working on his project?
View 1 Replies View RelatedSo I figured out how to insert a scale bar, it appears to be working, I just cant for the life of me figure out how to make the dang thing bigger! I cant "scale" the bar without messing it up. See attached pic, i want my new scale bar to be as big as the old (top) one.
View 5 Replies View RelatedI inserted our company logo and placed It properly in our title block. But when I zoom in with the mouse wheel the logo gets smaller in the border. When I zoom out it increases bigger than the border.
View 1 Replies View RelatedI am current CC subscriber and love all the different programs and the capabilities that come along with it. How to scale my artwork. For example, I have designed my business logo at 220 x 220 pixels. When I export it as a jpeg file to upload into my SharePoint team site and resize it, the quality diminishes considerably. Sharepoint recommends uploading a picture that is approximately 60 x 60 pixels. how do I take my 220 x 220 artwork and make it so that when I export it, it is 60 x 60 pixels?
View 2 Replies View Relatedhow the scales and printing works.
first i am working in meters .meters is choosen under the drawing settings tab .i am trying to test print at 1:1 a rectangle with 0.2 meters side that normaly will fit in a A4 sheet since the A4 is 0.21x0.297 METERS .
in the print dialogue i set the 1"mm" = 0.001 "units". the result is an image multiplied by 1000...arent the " units " METERS? METERS is what i use in the drawing so why i get a biger image?
if i set 1"mm"= 1 "unit" and NOT 0.001 i get correct 1:1 print .
what i am missing? c3d wants me to give 1mm=1meter?
I am not sure whether this involves annotative block.
My RCP at 1/8" scale looks okay. Yet in my 1"=10'0" POT plan,
I would like these exit lights/signages to appear double in size when printed,
(since POT is merely a schematic)
From 1/8" scale to 10' scale (96 to 120), the symbols by logic should appear
80% smaller, not larger.
Can this be done with annotative block?
How to print a viewbase layout with a large scale factor? The problem I'm having with ac2013 is that the print is coming out with jagged edge.
View 9 Replies View Relatedi m new in auto cad 2010 i today i face new problem i dont this is what? the message is that " the drawing contains a large number of annotation scales do u want to reset the scale list? "
View 2 Replies View RelatedWhen I insert an image as an OLE object, I cannot move it, scale it or anything? Am I missing something?
View 6 Replies View Related