How do I control the 'auto' option under DIMSPACE?
I have found that the entry listed as 'Jog Height Factor' under the 'Linear Jog Dimension' are of the 'Symbols and Arrows' tab of dimension style does the trick. However, does that control a variable?
I am trying to oTrack distance from the top circle edge of a cylinder to a certain distance ... whenever i try to do that ... it either track to x and y .. but not in z :/ ... the video i have on you tube he did it so simply and it seems to be easy .
I am not sure what is wrong .. but i heard parallel and perspective view could make a difference .. i actually try both :/ ...
[URL].....
I am trying to find a routine that will allow me to offset an arc by a distance and to a scale.
The offest command is very limited as to how far I am able to offset without the boject completely vanishing.
I am trying to make a flat pattern from a cone or something close to it. The routines and programs that I have found do not quite accomplish this very accuratll. They are always off on the upper and lower arcs and on the distance between the arcs. Tho this would not completely sovle my problem, it would allow me to get the distance between the top and bottom correct.
I see that there is an Inquiry tool for minimum distance between two lines but I can't find anything about the maximum distance.
View 6 Replies View RelatedI have located steel beams of an existing building roof frame. I am being asked to provide a distance from the theoretical roof to these points. The roof is sloped and I can create the sloped roof plane but I am unsure how to get the distance from the point to perpendicular to the theoretical roof slope, not the difference in elevation. Also would it be possible to label or make a table?
I am using Autocad 2013.
I used direct-distance entry to place the dimensions 3/8 away from the object lines... needless to say, while most horizontal dimensions are 3/8 away, the vertical and inclined dimensions are not. see attached. other than creating construction geometry and physically moving the endpoints of the arrows to the correct location, is there any way of getting this precise and correct the first time i do it?
View 1 Replies View RelatedI have change my units from mm to meters but when I make any drawings it apears 1000 or 100 when I really want 1.00 meters, how do I change this?
View 5 Replies View RelatedI am trying to set up a scale of a known distance on a photgraph that I have put in autocad. I know that this distance is 100mm, and have tried to work out how to mark this known distance, and then be able to work out the measurements of other dimensions in the photograph, including non-linear measurements. Is this possible?
View 2 Replies View RelatedI keep trying to draw a line by bearing and distance using the format @50.00'<N80d04'30''E. Everything enters but when I enter the last command of the bearing and hit enter it stays in the red boxed outline and does nothing. Upgraded to 2014 and trying to get things set for drawing property boundaries. Tried setting the units to surveyors mode and such but nothing works.
View 2 Replies View RelatedI thought there was a setting for this? I want to adjust the Osnaps so they appear further away from the point. IE: As I want to pick the quadrant I have to get so close to the quadrant before the osnap shows. I can't remember the variable to adjust this distance.
View 3 Replies View RelatedI was wondering if there is a way for me to setup Autocad so that instead of putting in S 88d20'12" W I could put in something like S88.20.12W so that I don't have to mess with apostrophes or "d." Also, can i do something similar with distance settings? Where instead of saying 5'-6 1/2" I can say 5.6.1/2. I know I could convert the measurements into decimals, but that would waste the time I would be saving with a faster input method.
View 1 Replies View Relatedthis Nudge command. Seems like it could be very useful, and I must say i like the IDEA of it (to those not familiar, you hold CTRL and hit arrow keys to slightly shift an object) but how to set the distance default on it. It seems to me to just move things by whatever distance it feels like.For my job specifically, I need 1/2" increments. how to set that variable?
View 9 Replies View RelatedIs there any way of displaying the geodetic distance(ie "mapdist") with the dimension tool instead of the normal distance?
View 2 Replies View Relatedhow to edit the line space distance for the dimension text. I can change the style, size and several other features. But the line space distance is the one thing I can't seem to edit. The only solution I know of and use is exploding the dimension and then the text turns to mtext and the option becomes available. But then if the section changes to a shorter/longer area, i have to go through several steps with the exploded lines. how to edit the line space distance for the annotation in the dimensions. i have also attached a pic of my issue as well.
C3D 2014 SP1
DELL Precision T3600
Intel Xeon E5-1650 @ 3.20GHz
NVIDIA QUADRO 4000 Dual Monitor
32 GB RAM / Win7 Pro 64-bit
Did 2013 change the way Direct Distance Entry is handled?
Say I want to start a line a distance of 3 from another line using Otrack and a running endpoint snap. Before, I could just hover over the existing line's endpoint, move the cursor in the right direction, and enter 3 on the keyboard. Now in 2013, I need to have Dynamic Input (F12) turned on to get this behavior. 2012 was not this way.
How to divide ellipse into line segments(equal/unequal lengths) of required accuracy or tolerance?
tolerance = mid-ordinate distance
When I try and connect with autoseek to get blocks the following message comes up. how to set firefox to accept this?
View 1 Replies View Relatedwhy does Auto Save always turn itself off? This would have to be the most frustrating thing ever, is there an answer to it?
View 9 Replies View RelatedAutoCAD insists on stacking fractions. I've tried everything I can think of to get the Auto Stack dialogue box to come up, but sometime I must have checked the "do not show me this again" box. I can't figure out how to reset the default to horizontal fractions.
View 2 Replies View RelatedI'm using Auto Architecture 2013 and the dimensions are always coming in on layer A-Anno-Dims; which is fine for plans. I also use dimensions for reflected ceiling plans as wells as other plan options. I want to set the dimension on the current layer, but no matter where I choose the command (ie command line, ribbon, toolbar, tool palette) it comes in on the same layer. Can I turn this option off? Is there a variable that I can chage?
View 9 Replies View RelatedI am in search of a add on program or a lisp that I can change an architects layers to the layers we use. I know layer translation command is available but every time I have to select what the layers translate to. It would be nice if there was a way to add the new architect layers into a database so when we run the lisp or program the layers will automatically change to our layers we use.
View 2 Replies View RelatedWhen I am working with 3D models, autocad keeps changing my ucs by a face I am near. I want to work in the current ucs and not change. How to change this setting?
View 3 Replies View RelatedI have one drawing with several thousand instances of the same block in it. Each block has a 'name' attribute. I want to populate those block attributes with a spreadsheet. What is the best way in AutoCAD 2013 to do that?
Ideas: the old ATTOUT, ATTIN commands from Express Tools....rather a dated method, but it might work
dbConnect: I've never used it, but might work.
Data Extraction Wizard: I think is just for data extraction from a drawing, but again not sure.
In 2010, I thought I remember the grid snap would automatically turn off when I was in a command for selecting stuff, then after completing my selection, the grid snap would automatically turn back on. For instance, if I wanted to isolate a layer, with grid snap on and set to 1/2x1/2", the object I would try to select would be in the middle of all the grid points and my curser would just jump around it. I'd have to F9 to turn off grid snap, then turn it back on when I was done selecting.
View 3 Replies View RelatedDirection of the "Auto Number" command
How to control the Auto numbering to start:
From left to right OR from right to left?From up to down OR from down to up?
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
I work making electrical projects and it is frequent for me to have a lot of lamps to number, sometimes hundreds.
how to number a group of objects automatically?
I am trying to figure out if there is a LISP or autocad add-on to start a library of architectural layers to be translated to our layers. So all I would need to do is hit a toolbar button and the LISP/Program would take a layer from archetects prints that I already added to a database that already knows what layer to change that layer to and so if there are different layers in the CAD drawing I can add them to the database so it will be saved for future layer translations. So once we get the database started I am hoping after awhile I wouldn't have to add any layers since they are already in the database to change the layers too.
View 8 Replies View Relatedunder options - I have the Automatic save unchecked
the program keeps saving after I do something in sheet set manager...like rename a sheet view
2013 Civil 3D
Recently installed AutoCAD 2014, and I'm currently trying to type the text:
TC1: 2/90 x 35 MGP10 studs with 4/2.8mm dia nails each end
It keeps stacking the 2/90 into the fraction 2 over 90. How can I turn auto-stacking off? I know I managed to turn it off for AutoCAD 2012, but now I can't find the option or system variable.
Realitivly new to 2013, upgraded from 2007.
We will alter the Arch Base CAD file layer colors to a muted color for use as our backgorounds. We would sort the Layers by color, so that we could group them together to one base color, so basically layer colors 10-19 would then become 19, 20-29 would be 29, layer colors 30-39 would be 39, etc... If the colors were one of the 9 Base Colors (Red, Yellow, Green...) Red is effectivly the same as color as 10, so then we would make it 19, etc...
In 2007, even thought the sorting was by layer color, the layers rows would remain in the same location until we applied the changes. But in 2013, if we sort by color then alter the color, the layer row will automatically be re-sorted to its proper position in comparison to all other colors. OK I get that, but, if we are altering 40, 50, 60 layer colors, that auto re-sorting is annoying, because then we need to rescroll to our last location to continue.
So, is there a way to turn off the re-sort until we APPLY the colors.
verify if this is the intended forward/backward compatibility between C3D 2014 & 2013.
My project was previously using Data Shortcuts in C3D 2013. I opened the reference (not the source) drawing that uses a bunch of Alignments. During the initial drawing upgrade from 2013 into 2014 I get a message for each Alignment that, "{Alignment Name} was modified in a previous version of the software. Changes in the current were overwritten when the data reference was synchronized.". At this point everything seems fine.
The issue I'm having is that when I re-open that upgraded drawing using 2013 all of those same Alignments become promoted. They are no longer referenced!