I used object snap tracking for years.Since I upgraded to AutoCad 2014 why does object snap tracking only work with Dynamic input turned on?
Personally I do not like to work with Dynamic imput on, when I use object snap tracking with out DI turned on it doen't work right. Past versions worked fine. What do I do to get this back?
I am having this problem for the first time with my most recent install of 2014 on a Windows 8 computer. When copying a line or any other object along another line as a base, when I type the distance that I want to copy the object, it deselcts the autosnap vector that I had specified. For example, now when I copy an object along a line at various intervals, I have to move my mouse after entering the distance each time to enable the object snap to reselect the direction I want to copy it (along a line that should stay selected through the object snap: nearest).
Is there some object snap or dynamic input setting that I need to change?
Did 2013 change the way Direct Distance Entry is handled?
Say I want to start a line a distance of 3 from another line using Otrack and a running endpoint snap. Before, I could just hover over the existing line's endpoint, move the cursor in the right direction, and enter 3 on the keyboard. Now in 2013, I need to have Dynamic Input (F12) turned on to get this behavior. 2012 was not this way.
I created a library of Dynamic cabinets in AutoCAD LT 2013. I have tested them and used them in drawings. I just upgraded to 2104 and when I insert those same dynamic blocks into a drawing, the parameters do not show and i can not use the dynamic block as intended. when I click on it...tons ot grips show up and no parameters.
View 2 Replies View RelatedWe recently switched to 64-bit ACAD on dell M6500 laptops. I used to use dynamic input all the time, but after the switch I noticed when using Dynamic input turned on, when you go to draw a LINE, after you pick the first point, the mouse "lags" and becomes "glitchy". I had the problem "fixed" once by our IT guy, he updated the driver or something and everything was fine.
But now it is doing it again.
using autocad 2013.
is there 3D object snap tracking?
I love the feature of Object Snap Tracking but for some reason or another it has stopped working. I normally use F11 to turn it on or go through the drafting settings menu to turn it on. The Object Snap Tracking box is checked and should work, but it doesn't. Is there a magic variable that needs to be set?
View 2 Replies View RelatedHaving trouble with object snap tracking. At times i am given distances from other objects to work with- which is what i am after.
However in some instances only the model space coordinates are displayed- not distances. Is there any way to ensure that only distances appear?
No matter whether Dynamic Input is on or off, input needs to be @X,Y in order to draw with relative coordinates.
Many students have installed recently AutoCAD LT 2012 Educational version and this problem appears only with one of them. Dyn Input Settings seems to be equal on all computers.
I cannot get Dynamic Input to work correctly on my AutoCAD 2013 installation. Polar Format is always the default no matter what the variable DYNPIFORMAT is set to. Neither using 0 or 1 as the setting will enable Cartesian Format to be the default for the second or next point. Changing the settings in the Pointer Input Settings dialogue box to Cartesian Format also has no effect. 2nd point always is entered as Polar Format. The over-ride for cartesian (,) does work though. I simply want the default to always be cartesian .
View 6 Replies View RelatedI really like the object snap tracking feature to snap between 2 points intersecting but I find it overly sensitive and hard to get it right the first time.
Is there a way to turn down the sensitivity? I use this feature frequently.
As I move my cross hairs over an object in a drawing it wants to select or highlight the object without clicking on it. On detailed models/drawings it takes alot of time and is almost impossible to use. Is there a way to turn or toggle this function off?
View 2 Replies View RelatedI've been working on a project for a bit and so far everything had been working correctly. But recently I must have mistakenly changed a setting I don't know about because now I am experiencing an issue.
When I am trying to enter a unit at the pointer, for example, the length of a line I am creating, if I use a space, AutoCAD seems to be treating it as ENTER and thus I can not specify my unit correctly.
In other words, if I want my line to be 3'-9 5/8" in length, I can type in 3'-9, but as soon as I hit the space bar in order to type in the 5/8" AutoCAD automatically finishes my line at a length of 3'-9".
I've update AutoCAD 2012 to AutoCAD 2013 and I have a problem when I type "L" or "C" to draw a line or a circle, the command line says "Unknown command "L". Press F1 for help". It's the same thing if I fully type the command "line" or "Circle". But some other commands works normally.
Working on:
Windows 7
Intel Core i7 2.93Ghz
8 Go RAM
NVIDIA Quadro FX 3800
Why AutoCAD 2013 turn off dynamic input when we use the insert command. It happens only when using dynamic blocks.
View 5 Replies View RelatedAccelerator Keys
My accelerator keys for the right-click object-snap cursor menu do not work. For example, I will be drawing a line and I will bring up the object-snap menu, then I will select ‘E’ for endpoint snap, the ‘e’ will display in the dynamic input window and the snap does not work.
I just switched from Autocad 2007 to 2013. how to display the object snap toolbar? the one with center snap, mid-point snap, etc options?
View 3 Replies View RelatedUsing AutoCAD Civil 3D 2013, now installing Service Pack 1 (kept crashing, this time it's working though), and I'm trying to find the area of a pathway that I've drawn in 2D with standard lines. Using the area tool, I want to find the area of the path, but it arcs around a 180 degree corner. I tried getting a rough estimate of the area by clicking at several points along each of the arcs, but after clicking a point where the arc joins the straight line of the straight section of the path, it literally won't let me click the next point. I can, however, specify the next point as long as it's nowher near the arc. Same goes for the polyline tool.
Just got an error code for the Service Pack installation, too. "A problem prevented the service pack from being installed, contact your administrator. Error 1603"
I am drawing a block that containes a number of other blocks which I want to control parametrically. For example. In one block, I have set the diameters of a circle restricted to 10 and 12-mm. I have a second block that also contains the circles which have similar restrictions. I now want to control the diameters of the circles from a single source - similar to shared parameters in Revit. Am I able to share a global parameter between blocks?
Eventually, I want to control a 2D drawing from a table only. Should I be using .Net or AutoLisp for this.
When using the block editor to rename an existing block to clean that instance of the block name out of the file, the block replace command from express tools does not work.
I select a block enter block editor save block as (new Name) save and exit block editor.Insert new block into the drawing.Express tab on the ribbon select Replace Block select block A to be replaced by Block B purge out instance of block A after complete. It reports 0 blocks replaced
attached is a file with 2 blocks called Drain and Drain X each have the same visibility states I want to replace Drain with Drain X to purge out Drain from my file.
I've just downloaded AutoCAD 2014 Student Version, and I can't seem to make my status bar on the bottom work. It's pretty annoying, as I couldn't manage to find the solution yet, did the access path to it changed compared to previous versions?
It's just blank grey (where OSNAP, DUCS, and other fun stuff's icons should be).
Can not change the font size or tracking in the Character Window. It always gets random numbers in the input field. System: MacbookPro Retina, OSX 10.8.4, Photoshop CC 14.0
View 1 Replies View RelatedInventor 2010
Some how I turned off the snap to end point in the sketch mode. where is the dialog box to control snap settings
We have just recently install Building Design Suite Standard 2014 and the tool palettes DO NOT work.
Clicking on the standard palettes that load with ACAD will not even work. We have also tried to make new ones and the will not MAKE (for lack of words).
Here is the Autocad warning it gives us:
Unable to execute the tool. Possible causes are:
-The tool is not registered properly. Please check your installation.
-the tool is from another application and is incompatible with the current application.
We are running a new copy and it IS registered.
Object Snap.jpg I want to pick the point where the circle hits the edge of the box but there seems to be no Intersection there. But they are on the same plane!
View 9 Replies View RelatedFirst, MY specs.
Processor: AMD A6-5400K APU (with Radeon HD Graphics) - 3.60 GHz
RAM: 8.00 GB
System: 64-bit
OS: Windows 8
Version: AutoCAD 2004 LT
Second, what we do.
Commercial MEP design. Project in mention is a 65,000 sq.ft. Italian food market.
Third, the problem.I am experiencing a selection and double click editing problem with AutoCAD 2012LT & AutoCAD 2014LT. On Friday, June 28th we recieved updated (not new) backgrounds from a lighting designer for two floors of the building whose MEP system we are engineering. The second floor had no problems really; we reset some annotation scales and the updated backgrounds plugged right in. The first floor, however, was so messed up that we copied and pasted the track lights and all else into our file directly (vs. xref'ing) and instantly, after a save, it is impossible to evoke any kind of edit with double click. In order for us to modify anything, we have to type the command before editing. So if I want to DDEDIT, I have to type that in before changing the text. If I do select the text first than CAD freezes, takes a huge dump, wipes for 5 minutes, and then the text editor appears. This problem is ubiquitous with all 2012 LT machines and up. AutoCAD 2005 LT has no problem (lmfao).
the layer order will not function as soon as the block is made dynamic. I have been creating my blocks the harder way and still have more to do, so what to do.
The last time I asked the Autodesk technician, I was told it is a program (Autodesk) issue which I call a bug. I have tried the draw order and the Textofront still, no better result.
I recently installed Autocad 2014 with Carlson Survey 2014. When I use Etransmit or file conversion i get a Fatal Error. when i uninstall the civil 3d object enabler, the problem goes away, but i need the object enabler and i need to convert files. Is this not a major issue that Autodesk would consider important enough to address, or is the object enabler minor in comparison to other issues?
View 4 Replies View RelatedIm using Inventor 2014 SP1 on a HP Z620 with 2 CPU - 16GB Ram.
Graphic card is a AMD Firepro W7000 4GB.
When i am rotating a big assembly 500+ it doesnt lag that much, but when i have a sketch turned on at the same time, the graphic lags extremely when rotating.
I have tried all the recommended drivers and the newest drivers and nothing changes.
I tried different hardware settings in inventor (Performance, Compability, Quality) and there is no difference.
I also tried to change the graphic Card with a Nvidia GTX 660.
It rotates much better (smooth) in big Assy than my firepro but it is having the same issue when having a sketch turned on.
I found an interesting dynamic block. It has a clipping boundary but you can drag the 'leg' out of the boundary. How can I make such block?
See attached dwg file.
Is it posiible to give the constrain for wipeout object in Dynamic Block.
View 3 Replies View Related