VideoStudio :: Unable To Capture File
Aug 15, 2012
I have a windows 7, 64 bit quad core with 8 Gigs of ram, and 500 gigs of hard drive. I'm using the latest Video Studio Pro x5. After some time, and not always at the same time, it stops capturing, and says "unable to capture video because it is copy write protected". It's not copy write protected, and I cannot figure out how to get it to stop doing that.
I'm capturing an old VHS tape using an Easy Cap (the one that is new, and works). Apparently there are some old Easy caps that do not work.
View 1 Replies
ADVERTISEMENT
Oct 23, 2011
When I connect my camera and select Capture Video, I receive the error:
Unable to switch to capture mode
Check if your video capture driver is working properly
15023:4:2
I select OK and it properly identifies my camera in source as Canon HV30
Using the VS Pro X3 software, I can play, ffwd, pause, etc the camera however, it will not Capture the video at all
This is on my dads pc. he is running:
- Video Studio Pro x3 Pro which has had all patches applied.
- PC is an intel i5 2500 on a Asus P8P67 Pro motherboard.
- 64 bit Windows 7 Home premium all patches applies
- Canon HV30 connected via firewire
Note, I have used this camera with VS Pro x3 on another pc with no issue.,
not sure if i have got a setting applied incorrectly in vs pro x3 or not.
View 9 Replies
View Related
Oct 10, 2013
Been using VidoeStudio Pro X5 for couple years and just picked up a used PC. It had XP and could capture with installed VS X5 with no issues. Today i upgraded to Windows 7, reinstalled VS X5 and cant get past the "Unable to switch Capture" error. I can capture using my Canon Vixia HV40 and Sony FX1000 via Firewire with no problems using HDV Split, Roxio Creator and Cyberlink Powerdirector, so problem must be somewhere with VS X5.I can "control" the camera (stop, play, rewind,etc) through VS X5, but the Capture and Option buttons are grayed out and no image in preview window.
I have tried googling and downloaded a few codecs and drivers but no joy. Naturally I have rebooted and tried fresh install as well
View 3 Replies
View Related
Mar 18, 2011
I am using X2. I have been capturing video from my camera with no problems. Today, I set it up again and now can't capture. When I press capture video, it runs for 10 seconds and then give a message that capture failed, file is corrupted and unusable and of course stop capturing.
I can't figure out anything that I am doing different than before when I captured successfully. I have restarted my camera, my computer, and video studio all with the same results. During the 10 seconds, I am getting video to my computer.
View 1 Replies
View Related
May 24, 2012
I'm trying to convert VHS to DVD. I have VS4Pro and a Hauppauge Collosus capture card and I get the error "unable to switch to cpature mode" when I'm in the capture tab and click capture video. VS4Pro recognizes the card but pops up the error "unable to switch to capture mode". In device manager, the drivers for the card appear to be installed/operating correctly.
View 2 Replies
View Related
Aug 6, 2012
Corel VSX4 now says "Either no video capture driver is installed in this system or do device is connected" now I am unable to capture new video from any source. W7 64B and I have downloaded the latest updates.
View 6 Replies
View Related
Apr 5, 2013
VS starts in Edit Mode. After connecting the video camera by a iLink cable to PC and switching the camera to Play mode, clicking on tab "Capture" an error message appears: "Unable to switch to Capture Mode. Check if your video capture driver is working properly" Question: How do I do it? I am not a computer savvy person, just want to capture, edit and finally burn my videos taken with the camera.
View 2 Replies
View Related
Feb 4, 2012
In capture mode, choosing "capture video"I get error message "failed to initialize the video capture plug-in another program may be using it or this file has been moved" " open driver failed" 152.00.43.0 15023.4.2 my video capture device is a USB WDM 2860 and shows in the "source" window but no "format" can be chosen and no video comes through. The operating system is windows 7 64 bit. I have "Magix movie edit pro 17" and "Cyberlink Video Director" and both of these programs work with the same device and capture. Neither one of these applications are running while using Video Studio. I checked and nothing else is utilizing this USB WDM 2860 device. I reinstalled the software, installed the patches, and uninstalled the USB drivers and reinstalled them.
View 6 Replies
View Related
Aug 27, 2012
I'm using Panasonic NVGS-25 camera + windows7 home premium + videostudio X5. When i connect my cam via FireWire, system see it and opens new window with proposition to capture video with VideoStudio, but when VS runs, it says that no devices detected or no drivers for it.
View 2 Replies
View Related
Mar 1, 2011
Is it possible to capture from a file using VS Pro X2? I'm trying to get an AVI file into my timeline. Can I capture the file or do I Import it to video clips and then drag it into the timeline.
View 7 Replies
View Related
Oct 28, 2011
I am having difficulty finding basic instructions for VS Pro X3. I transferred a film from my friends PC to my mobile drive. The film is avi format. I choose import from digital media, but cannot move it to the editing screen.
View 3 Replies
View Related
Dec 11, 2012
is there any way to change the screen capture file format to AVI? The only thing listed on the format listbox is WMV, and the quality is bad. This is for VideoStudio X5 Pro.
View 3 Replies
View Related
Jan 26, 2012
I have Corel VideoStudio Pro X3 as well as the trial version of X4 which I have just downloaded. I am having the same problem with both versions. When I go into Capture, there is no image coming through the Capture Window, it is just black. When I hit Capture Video, it does start capturing and it does record video correctly, however when I stop capturing, the preview window turns black again.
How can I get the video to be seen in the Capture preview window?
My computer is Windows 7 Ultimate 64 bit edition. I am using a USB capture device, the Diamond Multimedia VC500 One Touch VHS Video Capture USB 2.0.
View 1 Replies
View Related
Nov 13, 2011
I have a new mini recorder which records 720x480 at 29.897 fps. Video studio says Unable to open file *****.avi for all of the files. They play perfectly well with MS media player, VCL, Quicktime etc so what is wrong ?
View 9 Replies
View Related
Apr 13, 2012
I opened a previously saved project and all the AVI files have blank spaces. When I click properties it says the file is unreadable. When I try to open the file it says unable to open file, catastrophic failure.
These are the same files that I used to edit and render a video a few months ago, and I was able to successfully open the same file in Windows Media Player. I am using VSX4 on a Windows 7 laptop. I'm not sure what updates are installed.
The video file is DV AVI file (720 x 480, 28854 kbps data rate, 298788 kbps total bitrate, and 29 FPS).
View 4 Replies
View Related
Apr 18, 2011
After extensive editing I saved the result as an avi file. When I tried to open the newly created file I got the message:
File format mismatch. [1081.1.3]
I have many other video playback programs and, with the exception of Real Player, they all can play back this avi file I had just created with VS Pro X4. The Program GSpot finds no problems with the file.
Emails to Corel remain unanswered and telephone support held me waiting for hours, only to disconnect when it was their quitting time.
View 1 Replies
View Related
Sep 25, 2011
At the moment, the only file format that I can import on the edit tab is *.wmv. There should be no issue importing *.avi or *.mp4 or any other format for that matter, but it fails to open the files. I keep getting the same "unable to open the file 17101:7:1" error for seemingly no reason. Everyone says this software's functionality is wonderful, but if it won't even let you bring in normal files it's looking less and less useful all the time.
View 7 Replies
View Related
Jun 5, 2013
Not that it matters, I don't think, but I have been unable to burn an ISO file onto a usable DVD. In the Sharing module of VS Pro X6, after opting to burn a DVD, I select both "Create Folders" and "Create Disc Image." Both are created where I send them and I have no trouble creating usable DVDs by burning the folders onto a blank DVD after telling the Cyberlink burning software that I'm creating a video DVD. But I can't figure out a way to burn the ISO file disc image onto a DVD except as a data DVD, which, unsurprisingly, does not create a usable video DVD. (Cyberlink, at least, will not recognize the ISO file or the folder that it's in to burn a video DVD.) Is there a way within X6 to burn video DVDs from the saved ISO disc image (or from the saved folders for that matter) without re-rendering the video clips? (Also, while I'm asking, I take it that there is no difference between a DVD created from folders and the same content created from an ISO image. If this is right, why the two options?)
View 13 Replies
View Related
May 24, 2012
I thought I had read somewhere, before I purchased X4 Pro Ultimate, that BluRay could be burned to regular DVD if the files were small enough. Is that not true? Attempting to burn an 800MB file in BLuRay to a DVD+R yields an error message stating I need to use BD discs.
View 6 Replies
View Related
Nov 22, 2010
I am unable to insert a MP4 file from a GO PRO HD camera into the timeline.
i get a " file format mismatch" error message
I have read several posts relating to VS10 & other versions, but not VS11+
i tried changing the file extension to .MPEG-4 but this did not work
file size is aprox 1.7Mb
VS11+
V 11.5.0157.2 Plus
Extra Content Pack
Power Pack
VS11 Patch Eng 122507-03
View 5 Replies
View Related
Oct 2, 2011
In VideoStudio X4 (SP1), I am trying to import an edited (VSX4) project into the library in order to use parts of it in a different project. This is something I have done successfully before but the last couple of times I have tried I get the message: “Unable to open file. File format mismatch”. (1081:1:3) There is no problem opening up the project in the normal way it is only when I try and import it into the library. I have compared the properties of these files with the successfully imported files and, to me, they look identical. They were all captured from video in the same way,
View 9 Replies
View Related
Feb 2, 2012
This is driving me up the wall, I have pro X4 on my laptop and computer, I can't edit on my laptop as it lags, maybe Corel is too big for my laptop I don't know. On my laptop it allows me to import AVI. files, however, when it comes to my PC, it doesn't.It doesn't make sense how I CAN on my laptop but CAN'T on my pc, It did used to work fine on my pc when I had X2, but towards the end it started making the same error message
'Unable to open file [N:GFFILE309.AVI]. File mismatch'
I'm losing my temper, converting the files isn't an option as it makes my HD footage look like crap and pixilised, it also takes forever. I am at a dead end, I have installed the Corel Videostudio pro x4 codec and that hasn't worked at all.
View 5 Replies
View Related
Oct 15, 2012
I have a brand new machine with Iintel i7 windows 7 and 8mg ram, just bought VSX5 pro ultimate.
When I try to import "insert" audio file (mp3) I get back an error "file format mismatch" and so I am unable to insert it to the movie.
View 1 Replies
View Related
Dec 27, 2011
Circumstance: Using VSPX3, how to combine multiple VSP files in a single movie using "insert media file into timeline" command on File menu?
Each VSP file represents different segments of movie. Each VSP file has items on Overlay track, title track, Music track, as well as transitions.
Each VSP file can be loaded using "Open Project" command under File menu.
Problem: VSPX3 displays error message "Unable to open file" "file format mismatch" [16803:1:2]
View 4 Replies
View Related
Apr 11, 2013
I couldn't create DVD disk, or, couldn't create video file either. It would go to about 99% & then hang the system for hours (until stopped with Task Manager).
I had installed all of the updates, including SP2. I've uninstalled today & I will re-install in the next day or so to see if it works.
View 1 Replies
View Related
Aug 19, 2012
I was trying to 'create a video file' when I received this message, 'Ulead VideoStudio [2000:1:1] Failed to open the MPEG encoder.
I've made countless movies and this is the first time I'm having this problem. Maybe I had it in 2008, but I've just turned 70 and remembering what I did then is a thing of the past!
View 3 Replies
View Related
Apr 15, 2013
I'm not able to assign a Hotkey to enable me to use Corel Capture. No matter what I use, it tells me that the Hotkey is already being used by this system. I have deleted Hotkeys and then then tried to reassign them to no avail.
View 14 Replies
View Related
Feb 15, 2012
I have Ulead Videostudio 9. I am trying to capture from a DVD and following the manual instructions all goes OK up to the Import step. At that stage I get an error message "Temporary working forder does not exist. Report ID 0x8004083d(2109)" First time I have tried to capture stuff from a DVD. Program still works fine on all other aspects. I have checked the closed Ulead Forum and FAQ's but can find no solution. Is there anything I can do?
View 4 Replies
View Related
Jun 3, 2012
No Audio when capturing in VSX5. Also After I install the application any ac3 file or movie with ac3 audio will not play the audio.
View 8 Replies
View Related
Dec 18, 2010
I just purchased Video Studio Pro X3 and I love it . In my opinion it is possible to capture video from the video camera. I have a JVC HD camera
This the camera I purchased.
[URL]......
I would like to hook my camera up to my computer
[URL]........
How do I do this. Now of course my camera records off an SD card and I can just stick it in there and edit. The reason I am hoping I can capture video just like I can with a webcam is because the view screen on my camera no longer functions so therefore I can only point in my general direction and center up the shot in post edit.
View 3 Replies
View Related
Feb 25, 2011
I just bought VSx4 but I noticed it crashes as soon as I try to capture
my camera: canon HV20 -firewire connected
my OS: windows 7
I already:
uninstalled, re-installed VSx4
turned off/pc - camera
connected/disconnected camera
since I installed vsx4 I can't capture in vs x3 too.
View 6 Replies
View Related
