Revit :: Lines Along Curved Surface In Family Editor
May 17, 2013
I have an extrusion with a profile consisting of two offset arcs. This results in a curved surface.
I want to show a line in 2.5" from the top, bottom, and start and end edges of the curve. What I've done to accomplish this is to create two reference planes, one 2.5" down from the top of the extrusion, and another 2.5" from the bottom.
For the vertical lines, I then have to create a reference plane that is a chord of the arc of the surface, where the plane intersects the outer surface 2.5" from the edge on each side.
I have some other items that are being drawn on this curved surface, and to be honest, that's a bit of a pain. Am I missing some easier way to accomplish this?
If this was a project file, all sorts of options, but I'm not finding any in the family editor.
View 7 Replies
ADVERTISEMENT
Dec 12, 2013
When I save a selection in the family editor I can't seem to find the load selection button on the manage tab like you would in the project environment. The whole panel selection is not there. If I make a selection of at least two elements I get the load selection button on the modify tab. Is this as design or as forgotten?
At this moment it seems I first have to make a selection in order to load another selection.
[URL].....
and
[URL].......
View 1 Replies
View Related
Nov 13, 2013
Why am I not able to select Line Styles in the family editor? This is the case for both creating new families and editing existing ones. See attached image for clarification
View 6 Replies
View Related
Sep 28, 2010
I'm in an RFA file and can't seem to draw lines shorter than 1/32" without getting the "Element is Too Small on Screen" error. Even when I zoom in so that 1/32" is equal to the width of my monitor, I still get this error. I'm trying to draw very shallow grooves in a mullion. The attached shortline.jpg file show a line that is long on my screen, but to short for Revit, being drawn. how I can draw very short lines in the Family editor?
View 8 Replies
View Related
Apr 10, 2013
Is it possible to apply a decal to a curved surface? I need to place an image on a wrapping projector screen. When I try to place the decal, it only will choose 1 of the arcs or one of the straight peices. I need the one decal to stretch over the entire projector screen. I have attached a screen shot so you can see what I am trying to achieve.
View 3 Replies
View Related
Dec 9, 2013
I have some Symbolic Lines in a Revit Family, any time I go to "delete" any of them the file goes into "Regenerating" mode and will not come out out of it without hitting "Cancel". If go to move or copy a "Void" I have created in the files it does the same thing.
View 1 Replies
View Related
Oct 23, 2013
I've selected Symbolic lines for a family. I draw them and after importing them into the model I notice they're model lines for some odd reason. But when I go into the family and select the model lines the Convert command is greyed out.. What is causing this?
View 1 Replies
View Related
Nov 3, 2011
I am making a nested family of windows and inserted the windows as shared and I need them as non shared. Is there a way to change the window from shared to non shared in the family editor?
View 2 Replies
View Related
Jul 13, 2012
I'm having a random issue with the daylight ties lopes not tieing to the EG surface at all stations in the Corridor Section Editor. Some stations daylight fine. In plan view the daylight lines vary left & right as expected but don't display at all in Section Editor.
Some background info:2012 Civil 3D SP1 / 64 bit / WIN7Simple corridor used1 alignmentSame fg profileSame drefd EG surface (set all targets for daylight LT/RT)Only one assembly applied to entire corridor Attached are 2 captions of the issue I'm having which each have a cut & fill occurrence as well as a caption of the entire align. & corridor. I did try deleting corridor & recreating and even recreated a simpler assembly and still have the daylight issue in same areas of corridor.
View 2 Replies
View Related
Aug 6, 2012
I want to extrude a big number of pillars to a rather complicated surface and that works out fine. But each end of the pillars warps around the surface and I want them just to go up to it and stop with a resulting horizontal face.
View 1 Replies
View Related
Jan 29, 2014
I'm trying to align a nested family to a reference line in my host family so that it rotates around a certain point.
I've created the reference line in my host family, locked the end point to two reference planes and then gave an angular parameter to the angle between the ref. line and the ref. plane.
I then inserted the nested family and aligned it to the ref. line. The problem is that when I flex the angle, i get a "Constraints not satisfied" error..
What could be wrong?
I'm using a generic face based family for both host and nested families...
Using Building Design Suite Ultimate 2014
View 3 Replies
View Related
Apr 10, 2013
how I can add more volume to curved object surface? Say for example I have a plastic cup.You can think of this as cylinder object ,which was the shelled out using the shell tool and then had its base sealed.
Now at certain parts, I would like to increase the thickness and then blend it the rest of the surface(may be chamfer its edges) .
At certain parts on curved surface I would like to add an extra mm, I think if the surface was flat I would just sketch the shape, then extrude it by few mm and smooth the edges by doing a chamfer
But how can this be done on surface that is curved? Or multi curved for edges?
View 9 Replies
View Related
Sep 2, 2013
I would like to know how can put planar surface to solid object which surface is curved like cylinder for example. When start draw from first point rectangle of planar surface follow x cordinate not that solid object. How to do that simply?
View 9 Replies
View Related
Feb 28, 2013
I'm designing a press for a skateboard similar to: Rib Press
I have the board modeled: (see attached)
Now what i want to do is generate those ribs as seen in the picture.
I tried creating a block that intersected with the board and tried to split the rib at the surface, but to no avail. I think the issue has something to do with the curve of the board in two directions, but i can't seem to get it right.
if you are having trouble visualizing what i'm asking about, look at this. I want to be able to figure out the exact shape of those center ribs to print and eventually cut out of wood.
View 9 Replies
View Related
Jan 26, 2014
Having a time getting ribs to align 2m below top of ridge beam, and connect to curved wall below. I created one, then arrayed, but the radius changes at each 2.5 degree interval. I don't think I should have to calculate the % radius change to get the beams to do this. Some constraint button maybe?
Not sure if editing a wall profile is the best way to model this, but it's working.
View 4 Replies
View Related
Oct 19, 2011
If you look in the attached PDF, I have an elliptical wall that also has changes in elevation. call it a compound radius if you will. What I have to do is to make a wall cap to go on top of the wall. I know, sounds fun.....I have the surface on the right of the PDF and i need to figure out how i can take that shape and have it lay flat so that i can cut this shape out on my CNC. i know I can use the FLATSHOT command, but this will not give me the true shape of the board.
View 4 Replies
View Related
May 13, 2013
I am currently working in a facade that has a stylized gondola on it. The gondola has curved walls for the sides, and I need to have the curved cut to give it the shape. The tools I know are for straight walls, not curved. and the Opening/wall makes a squared opening, not curved.
View 3 Replies
View Related
Mar 29, 2012
After editing a value in the Family Table in the Content Center Editor I still get the old value. I tried to refresh this Content Center part (as administrator) but without succes.
In the logfile the error message is: "Failed: Unable to create part file. Unknown error."
Earlier (probably with older version of Inventor) I was able to refresh.
Is this a bug, or has this something to do with false settings
Autodesk Inventor Product Design Suite 2013 SP1.1
View 4 Replies
View Related
Sep 20, 2012
I am trying to give an Expression like sqrt({Jx}/{Section}) in column properties in family table editor. but its not working.
Find the attached image .....
Inventor Professional Suite 2010
Windows 7
View 5 Replies
View Related
Oct 1, 2012
Working on a drawing of a rocket. I would like to know how to alter text so it looks like its on a curved surface. The high point will be the center-line of the text.
View 1 Replies
View Related
Nov 27, 2013
So I need a starting point on how to draw on a curved surface.
[URL]
how to draw the "slot" I know in solid works i can "project" onto the surface and then so a cut.
View 9 Replies
View Related
Jun 13, 2011
I have a curved surface and I don't know a right way to export it. If it like Editable Poly then I have a mesh in DWG. Then I set to Faceted and optimized then merge faces (to receive one face) and then convert to surface but after that I have a surface with multiple triangles. This is one way which I use, I tried many ways but I have the same results.
This is what I have after export from 3DS MAX (same as DWG, SAT, IGS)
02_old.jpg
This is what I receive from splines and loft in AUTOCAD.
02_new.jpg
View 5 Replies
View Related
Dec 3, 2010
I need to make a label for a cup but haven't been able to. how to do it (theoretically), I don't how how / if I can use CorelDRAW to do it. I have included the video I used to find out how to do but it uses a different program that uses a "mould tool". Is there a tool that does the same thing on CorelDRAW?
[URL]
View 6 Replies
View Related
Nov 7, 2009
I'm loft retarded. What I did here was loft to a tangent work plane, then did a sketch on the top surface and extruded the shape that I want. There has to be a better & easier way.
View 9 Replies
View Related
Dec 13, 2012
Is it possible to extrude a curved 2D surface to give it thickness? For example, if you were to draw a loop the loop shape but it was just flat, could you extrude it out to give it thickness?
View 5 Replies
View Related
Sep 30, 2013
Basically I’m trying to create a circular cut in a flat pattern for a hole made in a rolled piece of sheet metal.
I have created a "case" (this is what we call it) to mount an axial fan, it will require holes for mounting the motor plate. When I create these holes in the rolled case assembly they appear to be fine, but when I flatten it they are turned into two sets of semi-circles or ellipses.
This is only a problem when we run the parts on our Laser; the laser will attempt to start the cutting at the end of each of these "semi-circles" causing a hotspot where the two semi circles meet. This causes the hole to be slightly smaller than intended in this area causing great difficulty inserting bolts, they normally require drilling.
Our material thicknesses vary from about 3mm to 8mm.
I’ve included a crude example of what I’m trying to achieve. To really see what I mean, place the file into a Drawing file and zoom into the hole. I couldn't add the file, with only 3 features the file was 5mb in size.
By the way, I have a temporary solution, it's just a little complicated. (My solution: use square holes first in the un-flat, use the diagonal lines from each corner of the square in a sketch on the flat pattern to place a circular cut on its mid points.)
Intel Xeon 3.0GHz (4 Cores)
nVidia Quadro 2000 (1GB) - Dual Screen
8GB RAM
View 6 Replies
View Related
Jul 8, 2013
I have tried, such as creating lines in a 3D sketch and projecting the geometry to surface, and creating a work plane, and both don't seem to work for me.... I'm trying to cut out a 5.8mmx14mm rectangle out of a cylinder. When I project the geometry to the cylinder's inner surface, I cannot trim the solid in order to extrude. I've attached the file.
View 9 Replies
View Related
Aug 8, 2012
Is it possible to hatch on a curved surface?
View 4 Replies
View Related
Apr 1, 2011
I've been working on creating a sword in 3D Max for the last couple of days and have run across a problem. At the base of the blade, it goes up straight for about an inch and then tapers out and up another half inch in a curve.From there, the blade tapers/curves back in, then out once more to create a thicker end of the blade, width wise. I need to know a simple way of doing those curves. A friend of mine suggested using quick loops, then individually scaling them to get the curving effect. That just seemed like it took too much time to me, and I thought there must be a simpler way. I tried adding a taper modifier to the selected area, but that didn't really seem to do much, except give the opposite effect that I wanted.
View 4 Replies
View Related
Nov 25, 2011
I'm using AutoCad 2007. I'm trying to map a simple 2D flat drawing onto a curved surface.
I have a 3D drawing of a very simple curved floor, similar to a skateboard ramp or a photographers infinity curve backdrop. I also have a 2D design. I simply want to drop my 2D drawing onto this curve, so that it follows the geometry of the curve's surface.
View 8 Replies
View Related
Apr 30, 2013
i wants to draw a circle on a cylinder's surface[3D curved surface]. And that circle should be co-planer with the cylindrical surface.
View 7 Replies
View Related
