I prepared my drawing for size A0 (841 mm / 1189 mm) but when exporting it in Jpg or Tiff format for printing, it happens something very strange. In the dialogue window it doesn't allow a bigger size than A1 (594 mm / 841 mm). It shows me 74 % for width and height parameters. I try to change it to 100 % but it turns back to 74. Now I cannot print it because I need the bigger size.
View 9 Replies
I have upgraded to X5 from X3 , and now when i Export EPS files, they are MASSIVE, I work in a company that does signs, and car vinyls and other graphics /vector related work, and It is important that i use EPS as file format for out " plotter" but a size of 800 mb and 2,2 GB now when it used to be 10 mb is insane.
I also use POSTSCRIPT 2, as 3, makes the file over 2 GBs.
i make a design in coreldraw x5 and export to pdf but i don't know the seeting how i compress pdf file size...so then its size is too large.
View 1 Replies View RelatedI just upgraded to x5 and can no longer export a file as an eps and hold the custom page size. In x4 I could export as an eps to a custom page size of 2.5" by 2.5". Every time I try to upload the file it is seeing it as an 8.5' by 11". I am selecting page size in advanced tab
View 8 Replies View RelatedWhen I export or publish to pdf from CorelDraw X6 the document size changes.If lets say i export an A4 page and then inport it again the size of the page has changed from 210x297 to 209,903 x 296,686 !
View 4 Replies View Related[ Bug ] Exporting to .GIF does not keep its original sizeThe checkbox 'Maintain Size' checked.
Result: importing that .GIF is 5 time size bigger.
we have just upgraded to x5 and now i have a big problem exporting tiff:
I work for print,not web. lets say i have a 50x50 cm layout. default dpi of document is set at 300. if i want to export that as a tif, it defaults at 300dpi in the export dialogue. until now, in x4, if i checked the maintain aspect ratio and just changed the dpi to lets say, 150dpi, it would only change the % of the size, not the actual size of the tif! now it changes somehow to double the size! but i want the same size to remain! also cm is selected, so no reason for it to keep the number of pixels!. i have to uncheck the maintain aspect and recheck it again to put the correct value in the size.
Also, i work with big documents, is there a way to stop previewing the jpegs in the export as jpg dialogue?
I am new to corel draw. i m using corel X6. i m having one arrow image (ie) 12px width and 23px height
I need the arrow in the same size with 24x24px transparent bg.
I am creating my files in 5x. The final product will be a printed 8.5 x 11 calendar. The company requires 300dpi resolution, and a bleed size of 1/16".
Product 8.5" x 11" Calendar
Final Size 8.5" x 11"
Bleed Size 1/16"
Resolution to Submit 8.627" x 11.127", 2588 x 3338 px, 300dpi
My page is letter size.The image is a bitmap composed of numerous photographs and vector graphics.
I have saved them to a CMYK BITMAP 300DPI.In Corel the image reads as 11.125" x 8.625"
When I export to a pdf or jpg the image size changes to 11.293" x 8.796" which will not work for the printer. It sets the design elements outside the 'safe zone'.
I have just upgraded to X6 from X5.
When I export a PDF the dialog window no longer opens and offers me the choices for crop marks, bleeds and so on!
This all use to work fine in X5.
How can I get this to start working properly again.
I receive an artwork from my customer to print a small label to cover some wrong printing.
The label is 110x160mm and the file size is 15MB.
So I intersect a small part of 4x40mm for the replacement label.When I save it as a new file, the filesize is 10MB!
I wonder why the small piece of artwork is so big, while it only contains a 4x40mm bitmap of 300dpi and the rest are vector.
[URL]....
I prepare an A0 size poster and with the vector graphics it is about 5 MB in size. When I started to insert a photos it reaches 50 MB. I carefully prepared my photos but for each 1.5 MB inserted image the size of the cdr file increases with about 7 MB.
You know, Corel hardly works with files bigger than 50 MB. I inserted 6 photographs 1.5 MB each of them but my cdr file became 50 MB and the program stopped working with it.
After finally getting X6 to be stable and usable I have two things I'd like to mention..
First, I've been using a 3rd party file manager called Ztree for years and one of its most wonderful capabilities is to copy paths to the clipboard which alleviates opening/saving frustrations with the typical Windoze Explorer dialogs. Anyway, one of the first problems I noticed with X6 is that Paste no longer works in the Open Drawing dialog, while it worked just fine in X5 and as far as I can remember, all previous versions. I sure would like to get that back.
My second complaint is the File/Export routine and specifically the presets. I do a lot of exporting to PNG and JPG and use multiple presets for fixed size/print resolution image output in both file formats. During the typical export session, I essentially export multiple different drawings all of which are exactly the same size/resolution in CD and in the past (X4 and prior as I recall,) was able to just hit <Enter> when the Export dialog appeared once the preset was set to the one I needed for that session.
In X6 though (and to some degree in X5,) even though the correct preset is listed, CD doesn't appear to recognize it, i.e., the math for the size/dpi conversion doesn't take place which forces me to waste time selecting "Original" or some other preset first, waiting for CD to render the new version, and THEN selecting the conversion preset that was pre-selected when I first opened the export dialog.
I try to export an illustration to eps with bounding box. When I import this e.g. with ghostscript, I get an error output like this:
GPL Ghostscript 9.05 (2012-02-08)Copyright (C) 2010 Artifex Software, Inc. All rights reserved.This software comes with NO WARRANTY: see the file PUBLIC for details.Displaying DSC file C:/Users/thomas/Documents/Konferenzen/ROSE2012/Grafiken/square.epsDisplaying page 1Error: /undefined in 1,00Operand stack:Execution stack: %interp_exit .runexec2 --nostringval-- --nostringval-- --nostringval-- 2 %stopped_push --nostringval.
[code]....
The problem seems to be at line "1,00 setflat".
I am using CSG X4 (SP2+hotfix) on a Win7 (32Bit) machine. I tried the following to figure out the problem:- varying export settings- using different programs to import (Ghostscript, Acrobat, CorelDraw)- trying complete re-install of CGS X4- changing the computer using the same version of CGS It seems that the eps export interferes with some system settings or installed printer drivers, but I am not able to isolate the problem. I would expect that the export filter is self-contained.
I tried to reproduce the problem with minimal content. The difference between the produced eps files may isolate the problem. A simple cdr-file, the produced eps-files and a snapshot of the used settings are in the zip-file located at URL....I assume that the eps files are built up from different resources but I cannot locate the involved files.
I have a number of files which were prepared in Corel Draw which I would like to post online. The designer has supplied the PDF versions of these files, however, the files sizes are too large for web usage. A 8 pg document is 5Mb. I have tried reducing the sizes by compressing in Acrobat; importing the PDFs into Corel Draw and re-creating PDF files with reduced resolution; recreating the PDF without the bitmap images (there are about 10 images)..yet the file size of the PDF does not change significantly.
What else can I do to reduce the file size of the generated PDF files? The files are newsletters, so most of the content is text and a few shapes and lines.
How to tell the file size of an image when in corel?
I have some big files that slow the computer down when working on them. Can I some how tell how big a picture is within corel draw.. ie It would be nice to be able to right click on a picture that I have imported into the workspace and it show me how many mega bytes it is.
Then I can go through my files and delete the larger pcs and make them smaller.
As it is now, I have to pretty much delete them all and start again to find dthe few pics that are like 3-5mb in size.
a tip for solving the problem of exporting an image as a tif led to another question. One solution to export as tif was to create a macro. See that solution post here: [URL] .......
It says : Step 1Run the built in macro. (Tools > Macros > Run Macro). In CorelDRAW versions prior to X4 (Tools > Visual Basic > Play). Select ‘File Converter’ macro from the ‘Macros in’ list and click ‘Run’
However in my macros drop down there are no macros. how can I get a file converter macro?
I chose to add the ico file format to my options for export in Photo-Paint, but when I go to export, it is not in the drop-down menu. What I need to do?
View 3 Replies View RelatedI have created a Marketing presentation in corelDRAW now I want to export it in MS Word format with as it is look and feel and editable text.
View 2 Replies View RelatedI wish to use the Corel X5 program for all of my engraving and sign business. I've been using a program, sign lab, where I export graphics in the plotter format to my Xenetech system. I will continue to export into my Xenetech. I found that the X5, export PLT only allows an outline but no real fill capability. I need a better program and here I am. Is there a better file format within Corel X5 to fill a graphic or font to accomplish this task?
View 5 Replies View RelatedI am working on a quite large file. It was all of the time around 68 MB. Now at once it is 570 MB in size. I linked all images (less than 380 MB) externally. What is the reason for that?
View 6 Replies View RelatedWhen I select "Save As" or "Export", the list of available file formats is only a fraction of what the help file shows as supported file formats. The help file instructs me to use the instructions in "To modify or repair a CorelDRAW Graphics Suite installation" but this does not work. How can I get or verify that all the file format filters listed in Supported file formats are installed in my CorelDraw 15?
Right now I am particularly interested in saving a CDR in the Visio (VSD) file format, but I would like to have of them available.
When I try to export a bitmap to PSD format or import a PSD file, the filter list does not show any import or export for Photoshop...what gives?
Corel Draw X5 version 15.20.686
Corel Draw Sign Designer
(CORELDRAW X6.3) Today I tried to export a .jpg file (text file) for a banner that was 6ft x 18ft. The export function wouldn't allow the 18ft, but changed it to like 9ft.
Tried in same in X3 and had the same result.
I could export the file as a .pdf and it worked just fine.
The question is, is there a maximum export size?
A .cmx file produced by CorelDRAW x5 can be opened / imported / edited in any previous version of CorelDRAW? Why size changes? When I export to .cmx size doubles. If I use the option "Save as ... cmx" the file size decreases. What´s the difference? URL.....
View 6 Replies View RelatedI've recently got a new computer, and after installing corel on it, I've found that I am unable to open files with corel, as soon as i press the open button corel crashes, but i am able to open the files when i goto the actual file in my documents and click open in there, and i am unable to save files any way whatsoever (due to crashing isues again) i am also unable to export my artwork to a jpeg, also an immediate crash.
View 8 Replies View RelatedHow do i program my corel photo paint to compress large jpeg photo file to a smaller size and save into another folder.
View 5 Replies View RelatedWill Corel6 (or later) ever be able to export to a web page directly since the HTLM export doesn't work (drops links). The Corel Web program, or what ever its name is, was a joke. Its amazing that Corel work puts its name on a program that you could not open a CorelDraw file.
My current work around is to export to a JPG and then import that into dreamweaver and add the links there, then post. A pain but it works.
Export is weird, maintain size is checked but it dose not give the proper size. My page size is 922x1344, but the image exported is half that size.
View 14 Replies View Relatedwhy (sometimes) when I export text or graphics as .eps files to my cutter it cuts the same outline up to four to five times and ends up cutting right through the backing paper. I have been using postcut with various corel editions since 1997 with no problems until recently. It also cuts random lines through lines of text which is such an expensive pain in the ass.
I started to use the production manager in flexi sign to cut my designs and same thing happens, except for the random lines but it will make up to five cuts on some objects. All text and graphics are exported the same. Has something in corel newer versions changed in relation to this?
i´m using CRD since X3 so I think i´m quite experienced with all the crashes and uncompatibilities but now I have a problem which I can´t solve.
I made a graphic project which is quite large (2,6m x 2,0m @ 300dpi) and including raster grahics. The CDR file itself has about 400MB. When I tried to export this graphic to the png or jpg at the current size Corel X5 always crashes. I tried almost everything on many computers but always the same problem.
It looks like the project is too large for export. At this moment I desperately need to export the file to jpg or png at full resolution. Maybe X6 is more stable when exports or I have to simplify the project somehow but...
FILE IS UPLOADED here and I need to have it 2,6m x 2,0m: [URL]
