Would it be possible to make a dynamic block for titleblocks with various layouts predefined in it?
To clarify, I currently have several titleblocks set up for the corresponding papersizes that i use, each one of these is a seperate block.
If i used a Dynamic Block could i incorporate several "layouts" into one block and one drawing?
usage of dynamic title blocks with visiblity states and defining page setup override templates which use same for quick plotting using sheet sets.
I have attached a simple dynamic block that I built which is the outter frame of our company title block, it is designed to allow users to quickly switch between Landscape and Portrait orientations.
The problem I am having is when I go to define page setups for my Sheet Set Page Setup Override Template I am unable to use the "Extents" option with auto-center because the "Extents", as defined by the page setup, includes ALL objects in the paper space regardless of visibility, so my title block ends up being centered in a stupid way if that printing configuration is used.
The only solution I have found is to use the "Layout" option when defining page setups, but this option produces other issues in other ways when printing. I don't want to use the "Window" option either for the potential for users to be using the page setup overrides to print drawings using different paper sizes or drawings that were not originally created using the current template the override is designed to accomodate.
Is there perhaps a system variable that defines whether invisible objects are included in the "Extents" setting in the page setup? I'm sure you'll all agree that Extents is the way to go in this situation, but it is not performing exactly as required.
I'm trying to make a dynamic block of a column radiator.
It should be very simple. It's a 46mm wide module that comes in a range of heights (300, 500, 600, & 750mm) and a range of assembly widths (9, 13, 18, 22 & 27 modules wide - more commonly given as mm widths of 414, 598, 828, 1012 & 1242 respectively).
My attempt at constructing it has gone quite well, but when 'stretching' the block a ghost of the core 414 (w) x 300 (h) unit remains. I attach the block to give you a better idea of what I mean.
I'm looking to make a simple 3D-Block. From what i read online you cant really create a 3d-dynamic block.
What I want to do: Create a simple cube, then being able to change the size of the cube either with grips or typing in the heights, widths, lengths for the X,Y,Z.
This cube will be used for showing the (No-Fly Zones) for particular areas where VAV-boxes go in a building.
I could create a 2D block with different sizes to it and then insert the block near the VAV-box and then burst or explode the block to then extrude the shape to a required height. (We are working in 3D here)
The purpose for all this! Its then used in Coordination meetings for other trades to see how much clearance there is and required for the HVAC trade.
I have a dynamic block that I created with a bunch of visibility, rotate and stretch parameters and actions. When I created said block, I meant to make it annotative but forgot about it during the initial block definition. Is there a way that I can make the block annotative now, or do I have to go back and re make the block all over again?
View 4 Replies View RelatedI'm trying to make a dynamic block of a triangle, wich could react to enlargement of bottom corner. The main thing would be that the angle between corners never change ( that means when increasing the weight, the hight also increases.. ). Already for some time trying to do that using Strech action, but nothing works out. Maybe I'm using not that action tool?
View 9 Replies View RelatedI want to make a dynamic block of just text. I want to be able to insert a block with a drop down pick list of preset texts and select the text I want it to display.
The attached file containing the various options of text I want to be able to pick from the list. I want to maintain the insertion point common to each text variation shown with a crosshair and the justification of the text as right and the height as 10. I would like to know how to add/remove variations to the block too.
LINK TO FILE IF ATTACHMENT DOESN'T WORK
[URL]......
I am not familiar at all with the controls in the block editor.
I would need to make a dynamic title block and I've tried alot of thing but can't find the solution.
I'll link my block here.
with the example I want in it.
symbole.dwg
I want to make a dynamic block that is made up of a rectangle. This rectangle will have an arrow on one side. The dynamic part will be to rotate the arrow to the center of any of each of the four sides.
View 8 Replies View RelatedI've got a D Block that should be REALLY simple. It's an equipment rack that you can array to the side to add more, and stretch up with a linear parameter to change the overall height of the rack. However, we usually have numbers marking the rack units going up the side of the rack. I know there's no way to make the numbers increment with a dynamic block, so I just took them out.
I put in markers so that you could see where the rack units were, but they're not arraying properly!
I have tried to make a dynamic block using annotative objects, text leaders, etc. The block was created initially as annotative but later somehow after going over it in the block editor. It has lost it's annotative properties. Is there a way to make a dynamic block that is not annotative, make it annotative. this block has only visibility features.
View 5 Replies View RelatedBasically I want to put a picture onto a video game controller.
I am trying to do the sticker part of this (the second step):
[URL].......
How to use the outline of the controller he provided as an overlay (is this even the right term?) onto an image so I know where to cut out.
We have some patterns that our customers can choose from to put sandblast film on their windows. Not sure about the english term for it, but this is what i mean:
We are looking for a flexible way to make the vector file from a predefined pattern.
Like the example below, when resizing the outer rectangle (= the window), the number of squares should be adjusted automatically. And the squares need to be centered in the window all the time.
I'm not such an expert in using patterns in illustrator, but i believe there is no way to define settings that control the pattern i believe? Like pattern brushes in illustrator, in which settings can be set like scale the pattern or scale the space inbetween, center the pattern,...
The square pattern below is just an example, see some other examples that i would like to easily control the thickness of lines, number of circles, space between stripes, horizontal and vertical scale of the pattern,...
I would like to make a 1" long, 1" diameter straight pipe as a block. I would like to insert that block into my drawing, say...on a 90 degree elbow. After inserting the straight stub, I would like to use a grip to "stretch" the pipe length to the next fitting. Ultimately, I would like to compile a parts list for my pipe drawing that will give me the straight pipe length. I've been doing some searching and 3d dynamic blocks seem to be impossible.
View 2 Replies View Related1. What is the easiest way to find points that are not constrained? I get a notice that the block is not fully constrained and its a nightmare going through all the lines trying to find where I need to apply a constarinet.( I can't wait to get off ACAD and back to Inventor.)
2. When I try to save a dynamic block using the Save Block icon under Open/Save, if the dynamic block is not fully constrained, and I click save, when I reopen the block to edit all of my constraints are gone, this has happened twice. Now I just exit by Xing out and saving changes.
So I've done a reasonable amount of work with dynamic blocks. I have a block with a rotation action and grip to arbitrarily align it. However I realized when trying to combine it with an alignment grip (which actions on the basic or fundamental block rotation angle) that there didn't seem to be a way to some how link a dynamic block rotation action or one of the custom angle properties to a the fundamental block rotation angle. Thus there are two additive rotations at work; the dynamic block one with its grip and the fundamental rotation property.
This can cause some confusion when one person aligns with the grip and another via rotating the block's fundamental property and would also be problematic in the generalized sense if one was trying to select or programmatically read back the net angle alignment.
I have a dynamic block, that represents a stirrup.
I inserted in the block a Block Propreties Table, that have some preset dimensions for the stirrups. The grip of this table I decided to put in the top right corner.
The problem is that I can't make this grip moveable )
See the attachement with the block
new to dynamic blocks but looking to streamline my wiring diagrams here and have created a block that shows the typical wire styles we use in a simple easy way. I now want to add an overall flip to the entire block and have not been able to find set this. I would prefer to use the same label and go from there. I have included the block to show what I mean. It is only working on the single visible item at the one time. I know this has to be possible just let me know what I am doing wrong. I am running AutoCad LT 2013
View 3 Replies View RelatedI need to create a dynamic block for a "Glass Panel" in a balustrade. I need to be able to insert it, in one corner and stretch it in another corner, to suit the staircase angle.
I've created the block, but it isn't working correctly. I've attached a drawing, with the left hand drawing a sketch of how it needs to be. The right hand drawing is my dynamic block attempt. As can be seen, when the block is stretched between the 2 points, it doesn't follow the angle of the staircase correctly (Very slight run off)
I wish to create a dynamic block containing some attributes. These attributes are inside rectangles that can't be modified in length using linear parameters ; but the attribute has to be always in the middle of the rectangle. So, I draw a line inside the rectangle (in a hidden layer) and insert the attribute with center justification (not sure for the translation) that I place in the middle of this line ; then I put a coincidence constraint (not sure for the translation, but it's the first one) linking the middle of the line with the middle of the attribute.
But here's the problem : when stretching my rectangle, the insertion point of the attribute suddenly changes from "center" to "bottom left".
I am looking for a way to use the ATTIN/ATTOUT workflow to bring in data from an excel spreadsheet to drive the size of each of my block's instances. The block will be simple, a rectangle, with width and length parameters. For each entity in my excel/csv file these parameter values are spelled out. I know how to display these parameters in my attributes, but I don't know how, if I were to feed in these values, to drive the geometry. If there's a better way to take a list of width and length values to generate a series of blocks each with a rectangle containing its respective size.
View 1 Replies View RelatedI need to do some repetitive task on a lot of dynamic blocks, unfortunately, when I open each file, AutoCAD keeps asking if I want to open it with the block editor.
Is there a way to disable that dialog and open the files as normal dwgs?
A hint: BLOCKEDITLOCK doesn't make it, it shows another dialog...
I have a drawing ("SURUBURI.dwg") with several dynamic blocks ("M12", "M16", "M18" ... an so on...). I want to insert in my current drawing, one of the blocks from SURUBURI.dwg, for instance the block named "M12".
For that i tried creating a new command "INSERT_M12" that has the following script :
^C^C-INSERT; "I:/Ionut Mihaila/Goodies/SURUBURI.dwg/M12"
Now obvious that doesn't work, but i think it shows clearly what i want to accomplish. So is there an other way to do this?
I'm working on a drawing and I want an action to work on two diffrent dynamic blocks.
In my case, I wish to have two blocks that I can rotate by one rotation grip.
How do I manage to work this out?
I have successfully created a dynamic block. I can insert it into AutoCAD, and it behaves like I want, except for one thing.
I can select the block and change it by taking a grippoint and place it at another position. So my block is e.q. stretched, just like I wanted.
But then. When I want to use the ordinary STRETCH command of AutoCAD, I can only stretch the insertion point of the block, but not the grippoints. Is there a way to set a grippoint to be select edable by commands like STRETCH.
I would like to create a "wave" dynamic block, see below...
It is made from wipeout.
Is it chance to make a similar?
If I make a list for the length (from 125 to 350), after can I make a table /list /summary where these size are shown?
Why the drawing title in my dynamic block will not scale up or down. The rest of the objects scale properly but just this the drawing title text attribute will not follow suit.
I tried adding position point and link, etc....I run out options and don't know how to fix this.
LT 2012 user
AutoCAD LT 2012
Windows 7 - 64 bit
I have a dynamic block with several actions and parameters. There are three grip points. Two are visible. One appears when you move one of the other grips. If i insert or paste this block near my template, the X/Y basepoint stays near the template when i drag the block on the template with one of the other two grips.. When i print the drawing the basepoint stays visible and the scale on my printed drawing is not correct (smaller).
View 9 Replies View RelatedI am creating a dynamic block of a conveyor belt it has a set number of widths and needs to be stretchable in length, which I have managed to do. The motor is placed half way down the length of the conveyor and needs to stay centered
I know I need to use the move command and put in a factor of 0.5 somewhere, but I can't remember how to do it.
I have a drawing with dimensions. Now, I want create Dynamic Block Controlling Visibility with dimensions in drawing with name dimension.
LT-don-TD LT-Kdoc-TD LT-Kngang-TDLT-don-thay LT-Kdoc-thay LT-Kngang-thayLT-don-moi LT-Kdoc-moi LT-Kngang-moiH-don-TD H-Kdoc-TD H-Kngang-TDH-don-thay H-Kdoc-thay H-Kngang-thayH-don-moi H-Kdoc-moi H-Kngang-moi
Then, I use command DAL; I can select dimension want use.
How do I stretch a hatch in dynamic block? It does not seem to work if I select the hatch along with other lines of a counter block.
View 2 Replies View Related