AutoCad :: Way To Make Numbers Increment With Dynamic Block
Nov 16, 2011
I've got a D Block that should be REALLY simple. It's an equipment rack that you can array to the side to add more, and stretch up with a linear parameter to change the overall height of the rack. However, we usually have numbers marking the rack units going up the side of the rack. I know there's no way to make the numbers increment with a dynamic block, so I just took them out.
I put in markers so that you could see where the rack units were, but they're not arraying properly!
View 9 Replies
ADVERTISEMENT
Jun 2, 2011
I have successfully used lisp ATTINC if normal blocks.
If not working in dynamic blocks.
When changes position of attribute becomes anonymous block (*U### = anonymous blocks).
I tried to use Unanon.lsp but disappear dynamic properties of the block.
View 7 Replies
View Related
Oct 16, 2012
I'm scaling a block with increment each 0.5 mm on x and y. But when I get out of the block the size is no longer the same.
Ex: 2,5mm scale gives 2.667mm
3mm --> 3,115, etc.
Hw can I fix it?
View 5 Replies
View Related
Oct 19, 2013
How can one add numbers in text strings that are in seperate blocks or dynamic blocks with pull down menus? I can get a sum of numbers in a text string to add up, but once it is in a block or dynamic block with pull down menus they don't all add up.
How can one bcount dynamic blocks with pull downs?
View 0 Replies
View Related
Feb 21, 2013
i have been trying for an option called auto numbering of attributes. i have a drawing of floor plan in every room there are 5 to 6 switch boards.I have to give a code and numbers to switchboard like SB1, SB2.......SB42 etc. there are like some 150 switchboards, so i have made an attribute with code and number. problem is when ever i have to add or delete some switch boards some where in the middle. again i have to start renumbering my switch board attribute blocks again from starting. It is very time consuming. is there any command renumbering all attribute blocks in one command.
View 3 Replies
View Related
Mar 26, 2012
I'm trying to make a dynamic block of a column radiator.
It should be very simple. It's a 46mm wide module that comes in a range of heights (300, 500, 600, & 750mm) and a range of assembly widths (9, 13, 18, 22 & 27 modules wide - more commonly given as mm widths of 414, 598, 828, 1012 & 1242 respectively).
My attempt at constructing it has gone quite well, but when 'stretching' the block a ghost of the core 414 (w) x 300 (h) unit remains. I attach the block to give you a better idea of what I mean.
View 4 Replies
View Related
Nov 26, 2013
I'm looking to make a simple 3D-Block. From what i read online you cant really create a 3d-dynamic block.
What I want to do: Create a simple cube, then being able to change the size of the cube either with grips or typing in the heights, widths, lengths for the X,Y,Z.
This cube will be used for showing the (No-Fly Zones) for particular areas where VAV-boxes go in a building.
I could create a 2D block with different sizes to it and then insert the block near the VAV-box and then burst or explode the block to then extrude the shape to a required height. (We are working in 3D here)
The purpose for all this! Its then used in Coordination meetings for other trades to see how much clearance there is and required for the HVAC trade.
View 3 Replies
View Related
Nov 21, 2013
Is it possible to increment text or attributes in a dynamic block? I'm want to create elevation text for grids that can start at a certain value and increment up or down from there.
View 1 Replies
View Related
Sep 18, 2013
I have a dynamic block that I created with a bunch of visibility, rotate and stretch parameters and actions. When I created said block, I meant to make it annotative but forgot about it during the initial block definition. Is there a way that I can make the block annotative now, or do I have to go back and re make the block all over again?
View 4 Replies
View Related
Nov 28, 2011
I'm trying to make a dynamic block of a triangle, wich could react to enlargement of bottom corner. The main thing would be that the angle between corners never change ( that means when increasing the weight, the hight also increases.. ). Already for some time trying to do that using Strech action, but nothing works out. Maybe I'm using not that action tool?
View 9 Replies
View Related
Aug 6, 2013
I want to make a dynamic block of just text. I want to be able to insert a block with a drop down pick list of preset texts and select the text I want it to display.
The attached file containing the various options of text I want to be able to pick from the list. I want to maintain the insertion point common to each text variation shown with a crosshair and the justification of the text as right and the height as 10. I would like to know how to add/remove variations to the block too.
LINK TO FILE IF ATTACHMENT DOESN'T WORK
[URL]......
I am not familiar at all with the controls in the block editor.
View 9 Replies
View Related
Oct 29, 2013
I would need to make a dynamic title block and I've tried alot of thing but can't find the solution.
I'll link my block here.
with the example I want in it.
symbole.dwg
View 9 Replies
View Related
May 18, 2013
I want to make a dynamic block that is made up of a rectangle. This rectangle will have an arrow on one side. The dynamic part will be to rotate the arrow to the center of any of each of the four sides.
View 8 Replies
View Related
Aug 14, 2008
I have tried to make a dynamic block using annotative objects, text leaders, etc. The block was created initially as annotative but later somehow after going over it in the block editor. It has lost it's annotative properties. Is there a way to make a dynamic block that is not annotative, make it annotative. this block has only visibility features.
View 5 Replies
View Related
Jun 24, 2010
Would it be possible to make a dynamic block for titleblocks with various layouts predefined in it?
To clarify, I currently have several titleblocks set up for the corresponding papersizes that i use, each one of these is a seperate block.
If i used a Dynamic Block could i incorporate several "layouts" into one block and one drawing?
View 8 Replies
View Related
Aug 25, 2011
I have a series of blocks that I need to insert into a drawing, maybe 100-200 times and then change one of the 6 attributes by an increment of 1.
I've looked at some of the older posts and have not been able to do this. Is it possible to take the tag regerence, in this case OUTLET_REF and automatically add 1 to it when the symbol is inserted.
Can this be done using Diesel or with a bit of lisp?
View 9 Replies
View Related
Mar 1, 2011
how do one wants to do a polar increment angle to make a degree in a autocad drawing. I want to design a truss but at the angle of the truss , how to make an angle between the top chord and lower chord. which icon i should click on ?
View 3 Replies
View Related
Jun 5, 2012
I would like to make a 1" long, 1" diameter straight pipe as a block. I would like to insert that block into my drawing, say...on a 90 degree elbow. After inserting the straight stub, I would like to use a grip to "stretch" the pipe length to the next fitting. Ultimately, I would like to compile a parts list for my pipe drawing that will give me the straight pipe length. I've been doing some searching and 3d dynamic blocks seem to be impossible.
View 2 Replies
View Related
Sep 20, 2013
1. What is the easiest way to find points that are not constrained? I get a notice that the block is not fully constrained and its a nightmare going through all the lines trying to find where I need to apply a constarinet.( I can't wait to get off ACAD and back to Inventor.)
2. When I try to save a dynamic block using the Save Block icon under Open/Save, if the dynamic block is not fully constrained, and I click save, when I reopen the block to edit all of my constraints are gone, this has happened twice. Now I just exit by Xing out and saving changes.
View 2 Replies
View Related
Mar 22, 2013
So I've done a reasonable amount of work with dynamic blocks. I have a block with a rotation action and grip to arbitrarily align it. However I realized when trying to combine it with an alignment grip (which actions on the basic or fundamental block rotation angle) that there didn't seem to be a way to some how link a dynamic block rotation action or one of the custom angle properties to a the fundamental block rotation angle. Thus there are two additive rotations at work; the dynamic block one with its grip and the fundamental rotation property.
This can cause some confusion when one person aligns with the grip and another via rotating the block's fundamental property and would also be problematic in the generalized sense if one was trying to select or programmatically read back the net angle alignment.
View 2 Replies
View Related
Jun 13, 2013
I have a dynamic block, that represents a stirrup.
I inserted in the block a Block Propreties Table, that have some preset dimensions for the stirrups. The grip of this table I decided to put in the top right corner.
The problem is that I can't make this grip moveable )
See the attachement with the block
View 1 Replies
View Related
Jul 25, 2012
new to dynamic blocks but looking to streamline my wiring diagrams here and have created a block that shows the typical wire styles we use in a simple easy way. I now want to add an overall flip to the entire block and have not been able to find set this. I would prefer to use the same label and go from there. I have included the block to show what I mean. It is only working on the single visible item at the one time. I know this has to be possible just let me know what I am doing wrong. I am running AutoCad LT 2013
View 3 Replies
View Related
Feb 28, 2012
I need to create a dynamic block for a "Glass Panel" in a balustrade. I need to be able to insert it, in one corner and stretch it in another corner, to suit the staircase angle.
I've created the block, but it isn't working correctly. I've attached a drawing, with the left hand drawing a sketch of how it needs to be. The right hand drawing is my dynamic block attempt. As can be seen, when the block is stretched between the 2 points, it doesn't follow the angle of the staircase correctly (Very slight run off)
View 9 Replies
View Related
Nov 21, 2011
I wish to create a dynamic block containing some attributes. These attributes are inside rectangles that can't be modified in length using linear parameters ; but the attribute has to be always in the middle of the rectangle. So, I draw a line inside the rectangle (in a hidden layer) and insert the attribute with center justification (not sure for the translation) that I place in the middle of this line ; then I put a coincidence constraint (not sure for the translation, but it's the first one) linking the middle of the line with the middle of the attribute.
But here's the problem : when stretching my rectangle, the insertion point of the attribute suddenly changes from "center" to "bottom left".
View 2 Replies
View Related
Dec 4, 2013
I am looking for a way to use the ATTIN/ATTOUT workflow to bring in data from an excel spreadsheet to drive the size of each of my block's instances. The block will be simple, a rectangle, with width and length parameters. For each entity in my excel/csv file these parameter values are spelled out. I know how to display these parameters in my attributes, but I don't know how, if I were to feed in these values, to drive the geometry. If there's a better way to take a list of width and length values to generate a series of blocks each with a rectangle containing its respective size.
View 1 Replies
View Related
Nov 7, 2011
I need to do some repetitive task on a lot of dynamic blocks, unfortunately, when I open each file, AutoCAD keeps asking if I want to open it with the block editor.
Is there a way to disable that dialog and open the files as normal dwgs?
A hint: BLOCKEDITLOCK doesn't make it, it shows another dialog...
View 4 Replies
View Related
Jul 16, 2010
I have a drawing ("SURUBURI.dwg") with several dynamic blocks ("M12", "M16", "M18" ... an so on...). I want to insert in my current drawing, one of the blocks from SURUBURI.dwg, for instance the block named "M12".
For that i tried creating a new command "INSERT_M12" that has the following script :
^C^C-INSERT; "I:/Ionut Mihaila/Goodies/SURUBURI.dwg/M12"
Now obvious that doesn't work, but i think it shows clearly what i want to accomplish. So is there an other way to do this?
View 9 Replies
View Related
Sep 18, 2013
I'm working on a drawing and I want an action to work on two diffrent dynamic blocks.
In my case, I wish to have two blocks that I can rotate by one rotation grip.
How do I manage to work this out?
View 1 Replies
View Related
Feb 4, 2011
I have successfully created a dynamic block. I can insert it into AutoCAD, and it behaves like I want, except for one thing.
I can select the block and change it by taking a grippoint and place it at another position. So my block is e.q. stretched, just like I wanted.
But then. When I want to use the ordinary STRETCH command of AutoCAD, I can only stretch the insertion point of the block, but not the grippoints. Is there a way to set a grippoint to be select edable by commands like STRETCH.
View 9 Replies
View Related
Mar 1, 2013
I would like to create a "wave" dynamic block, see below...
It is made from wipeout.
Is it chance to make a similar?
If I make a list for the length (from 125 to 350), after can I make a table /list /summary where these size are shown?
View 9 Replies
View Related
Jun 27, 2013
Why the drawing title in my dynamic block will not scale up or down. The rest of the objects scale properly but just this the drawing title text attribute will not follow suit.
I tried adding position point and link, etc....I run out options and don't know how to fix this.
LT 2012 user
AutoCAD LT 2012
Windows 7 - 64 bit
View 3 Replies
View Related
