I'd like to place a point at a specific "Z" level on a line. The line is not perpendicular to the x~y plane. On the attached .dwg, say @ z+.750 on one of the angled lines on the "constraints" layer.
0699 Cadtutuor.dwg
How do I draw perpendicular from a line or object at a specific point? I know by holding shift and osnap perpendicular I can draw the line but I can not osnap to the exact point!
View 9 Replies View RelatedIn PS5, if I start with a picture 5184 x 3456, I could crop a picture to be 2100 by 1500 by setting these parameters in the crop tool. No matter whether I decided to make a big crop or a small crop, my final image was always 2100 x 1500.
In PS6, however, I don't think the crop tool parameters work the same way. If I set the crop parameters to 2100 by 1500, my final crop is NOT 2100 by 1500, but rather my final crop is whatever original pixels I selected.
What is the EASIEST way to accomplish a final crop of 2100 x 1500 on PS6?
I have multiple icons placed in a document, from several different sources (all are vector objects) -- see the included image. They vary in size and what I would like to do is find a less onerous method of resizing all the heights to a specific size, while scaling the width proportionately. I have found several scripts that come close to a solution (see links below), but none that allow me to input a height (or width) in inches and have all the objects resize to that height proportionately.
Change Width to the Width of the narrowest object --> Script01
Change Height to the Height of the shortest object --> Script02
Change Multiple Attributes (JohnWundes) --> Script03
icon image (couldn't place via Adobe Forum) --> click
I'm trying to draw a plan of my house in Autocad 2009 but I seem to be endlessly using trim and extend because I can't easily select the points that I want with osnap. Eg. imagine I have a box, and I want to start drawing another box inside it that has each side as 10 units smaller than the corresponding side on the outer box.
Step 1 - I draw a small line from the top left corner of the big box using the endpoint snap, typing in "5" for the length.
Step 2 - I then do the same at right angles to the first line to get me to the starting point of the inner box. This always leaves me with 2 small lines to remember to delete.
Step 3 - Then in order to draw the top line of the inner box I end up drawing to a random length because I can't say "draw until 5 units away from the right hand side of the big box", then I end up trimming it later once I've repeated steps 1,2 and 3 for the next side of the inner box.
I know in my example above I could have scaled the box down or something but that's not what I'm getting at. I really want a way of selecting line start and end points that are a known position away from an existing point.
This seems like something that should be really easy but for the life of me I can't figure it out. I even started looking at using the Subassembly composer to create a custom SA but that seems like a ton of work so something that would seem to be a common problem.
I need to provide a v-ditch with 2:1 side slopes at the toe of a 2:1 fill slope. The flow line of the ditch should be 2 ft below the daylight point of the roadway pavement section.
My problem is that the conditional subassembly seems to evaluate the height of fill directly beneath the attachment point of the conditional SA (pavement section daylight point in my case – “Daylight_Sub” Point code). Instead I need it to evaluate the difference in elevation between the catch point of a 2:1 daylight fill slope and the conditional SA attachment point (Daylight_sub). If that difference is less than 2 feet, I need to provide the ditch, otherwise I can just use the daylight slope for the ditch foreslope and the existing surface for the backslope.
how to do this? Maybeits as easy as using a predefined daylight subassembly that I'm overlooking?
Here’s my current assembly attempt:
And the resulting behavior. It is solving the 2nd fill condition when I would like it to solve the 1st fill condition:
Just trying to reduce the height of the command line. I thought you just had to hover the mouse over it and drag it back down I have 3 rows plus the command prompt line
View 5 Replies View RelatedI want to know is a point(for example p1) is on the right of an alignment?
View 3 Replies View RelatedMy question is how do i extend lines to a specific point? I have attached a before and after image below for an example. But obviously it takes to long to do this line by line and getting the spacing correct. Is there a way to do this?
Capture2.JPG-----------------------------> Capture.JPG
I would like to use the behaviour of "drag and drop" into AutoCad (from a listbox in a form) at a specific point, I do not need to drop anything into AutoCad, I just need the exact point of the mouseposition converted to WCS in autocad.
the below code works, but i do not get the correct point in AutoCad.
Private Sub ListBox1_MouseDown(ByVal sender As Object, ByVal e As System.Windows.Forms.MouseEventArgs) Handles ListBox1.MouseDownDim ed As Editor = Autodesk.AutoCAD.ApplicationServices.Application.DocumentManager.MdiActiveDocument.Editor '---now i drop listbox-text in autocad, DoDragDrop(ListBox1.Text, DragDropEffects.Copy)Dim pt As Point3d = ed.PointToWorld(New Point(CInt(MousePosition.X), CInt(MousePosition.Y)))'---draw circleModelspaceAdd(Teken.Cirkel(pt(0), pt(1), 100))End Sub
(Maybe it is possible to just change the mouse-cursor, but it doesn't 'lock' the selected item in the listbox, as if it was dragged into the drawing.)
I have a 3d Drawing with very detailed light source descriptions. Is there any way I can measure a light intensity (in lux) in a specific point of my drawing?
View 0 Replies View RelatedIs it possible to change the row height in a Line and Curve Table.
Civil 3D 2012
I have a line or a pline segment and i want to start a line from a point laying there and go perpendicular outwards. Is there a way to do it with tracking?
Yes, i saw the command draw line at an angle but i find it a little bit complicated for a simple task like that. I am sure autodesk have a simplest solution about that.
If i am already at the draw line mode and i can easy catch the tracking perpendicular to previous segment but if i want to start from another line and go perpendicular i cannot make the tracking work.
I've had a simple lisp I've been using for years that suddenly disappeared. It required that you identify a block name, tag name, and the value that you want the tag to be. All of this is performed via command line, so it is scriptable. Since I lost it, I've been experimenting with -attedit. This command comes frustratingly close to what I'm looking for, except it only appends an existing tag, or replaces a specific string within the tag; I can't get it to replace the entire tag, regardless of its value.
1> Any lisp routine that does what I describe?
or
2> How to make -attedit replace a tag value without regard to what the value currently is (like a * wildcard)?
Which settings or where do I go to set my drawing Style, Text height and line space factor on all my drawings in one shot. It is frustrating going through many drawings changing it.
View 9 Replies View RelatedHow do I configure AutoCAD 2010 to point to a specific folder for the plot styles (ie. *.ctb files)?
View 2 Replies View RelatedI need to draw an ellipse at a specific point on a drawing.
i can calc the major and minor and i have a polar point of where it should be drawn.
i just need the code to draw the ellipse.
I made an alignment of road, inserted with sample line, then i made a profile. But on the sample line on profile, there is not a data of height and lenght of profile. How to get those data in road profile. I can manually draw that, but i think there is an easier way?
View 1 Replies View RelatedI would like to draw a Zig Zag Line, but I want that the line start in point "A" and finish in point "B".
The image below is similar to how I want the line, but I would like to have that "wavy" style. I use Illustrator CS6.
I want to align a line of length say 3m between two intersecting lines. How to do it in autocad.
View 9 Replies View RelatedHow do i draw line at specific angle. if i have the length on the x axis and angle, when i do @.25<45 the line becomes .25 in length i need the x dim to be .25 @ 45 degrees. as shown in the picture
View 9 Replies View RelatedI need to move areas of an image that I have selected using the unit of points.For example, I get corrections in our copy where I need to move certain parts of the image 8 points up or over 3 points.
I can use the measurement tool to meausure the distance but then it disappears when I try to actually move the selection. The same thing happens when I try to use guides to mark the area. I wish I could just set Photoshop to "nudge" in points instead of pixels.Is there any way to make this easier?(Photoshop CS4 version 11)
Can you lock a line so that it cannot be moved or erased? Not a layer...a specific line.
View 3 Replies View RelatedIn Illustrator CS5 my anchor point handles are snapping to specific angles,which I don't want. I have to turn off Smart Guides to freely adjust the handles.
Under preferences, Smart Guides, I turned off the custom construction guides, but even this did not correct the issue. I love using Smart Guides and I thought there were just in face that 'guides' and provided no snapping.
I also tried turning off 'snapping to point' to see if that was creating an issue, but no dice.
I can provide my system settings in case:
Mac OSX 10.8.4
16 GB memory
Illustrator CS5
Wanted to ensure I was not missing a feature I couldn't find or research before trying to reset my preferences.
RE: Autocad LT not able to move an entity along a line a specific distance using cursor snap and dynamic input
What I want to do is move a line on an angle a certain distance in the direction of the line itself in this case 20mm
What used to happen is you'd simply select move and an endpoint on the line then hover over the mid or opposite endpoint of the line and enter 20 and it would move 20mm along the trajectory of the line.
The same set of actions now only seem to allow you to move the entity 100mm (the default value) along itself in the correct direction. If you enter 20 it does not move and if you enter 50 it moves 100!
I’ve got some questions about custom line types:
1.How do I create Custom Line types that have specific TEXT in it? Like -----L-I-N-E-----
2.Then How do I load that Custom Line type every time I open a new CAD File Dwg.?
I am drawing a diagram to describe a mathematical word problem. Since it is easier to visualize with a drawing, I want to draw it using the given dimensions. But angles used in the diagram are unknown and are not needed for the answer to be calculated, so the only way to draw this freehand is to guess at the angle resulting in the correct distances to be off.
Here is the word problem: There are two ladders, one 40 feet and the other 30 feet, each touching the base of one of two buildings and leaning against the other building. If the ladders cross 10 feet above the ground, how far apart are the buildings?
So for my drawing, being rather simple considering what AutoCAD can do, results in this:
Can AutoCAD calculate the angle needed to place a line of a given length between two parallel lines that are a distance apart less than the length of the line to place between them, having the endpoints of this line touching the parallel lines, fitting exactly?
For the word problem, the distance between the two parallel lines is what needs to be solved and the math is quite invloved, having to find the roots or solution of a quartic equation. (I have the solution figured out to be 26.03287754 feet)
What I am afraid of is that this would require to program an AutoLISP routine to create a new command that one can call from the command line. I see it using the the measure command with relative and absolute co-ordinates. This may be far from a "beginner" question. I can do this quite easily on a peice of paper: having two parallel lines drawn, take a ruler and placing the "0" mark on one line, then adjusting the angle until the desired length just reaches the opposite parallel line. I used to use this trick quite often when drafting with pencil and paper to divide a distance into a required number of even amounts, so this can't be that difficult to do with AutoCAD!
how to give line height to text in AI Script
View 3 Replies View RelatedI'm trying to figure out the height of my line segment. It has a 1.5 stroke point. How many inches is that?
View 3 Replies View RelatedI am trying to find out if it is possible to start/load the animation based on a specific point in its timeline? The animation I am creating is a parallax animation based on mouse position and I am trying to load it in the middle of the animation and based on the users mouse position will play forward or backwards from that point.
View 2 Replies View RelatedI need a lisp which is i can draw a line or pline with circle in every 30 meters ( circle diameter and total line or pline length will be optional )
View 6 Replies View Related