AutoCad :: How To Not Make Curved Line Break Into Straight Line Segments
Jun 27, 2012
I draw a curved line and would like it to remain as a curved line even after saving the file. However everytime after saving, and opening the file again, the curve breaks into many line segments, which is not what I want! I want the curved line that I draw to remain as a curved line even after saving and opening. How do I do that? I am using autocad2010.
I use the ARC command to draw a couple of lines, they look okay here. But after I saved it, and re-open it again, what previously appeared as curved lines changed in their appearance to polyline segments.
If there is a way to "flatten" a non curved polyline or series of lines to one straight segmented line, without altering the distances of each segment?
I have one LW polyline consisting lines and one or two arcs. I want to calculate length of all line segments and arc segments separately and the resulted values to be shown as attributes (seperate attributes for line segments and arc segments).
I needed to remove a feature line that I used as a break line when creating a surface. When I removed the feature line from the definition of the surface, the grading did not change. It appears the points created by the feature line remain which is why grading didn't change. The only work around was to delete these points.
I noticed the same thing happens when I removed the surface boundary and inserted a new boundary. why these points remain and how to remove when I delete boundary and feature line from surface?
This layer is styled so that all text is centered. In this case, FDO_LAYER2 is having it's text left aligned. I'm pretty sure this is due to the method I am using for a new line. Is there something else I can use to break the line and maintain the center styling?
Using a second point for FDO_LAYER2 is not an option.
How can I draw a straight line without that protractor shaped dotted line following my cursor making it lag and also not snap correctly to the next line? Also, I have noticed that I can't set my user interface to auto cad classic settings. There seems to be no option for it in workspace settings.
how to break diameter line into horizontal line at the end ?... there's no such option in editor style (I want to have 2 arrows for this diameter, not one as it is in editor options)
How do we do a break and or jog line in a section so we make things shorter? I did find the DIMJOGLINE command and that will be great for the dimensions but what about the other stuff, do we have to do that with a block or draw the thing, if that's the case what are you doing to handle this?
In PSCS5 and earlier, I used to be able to make a straight line of points in a curve by placing 9 points on the straight line curve. I did this by drawing a small straight line at the bottom of the curve using the pencil tool and then clicking the curve point icon.
In CS5 and prior versions of PS, you could "make a straight line of points in a curve". After opening the curve dialog box, draw a straight line with the pencil tool and then click the wavy icon above the pencil tool icon (edit points to modify the curve) and it would automatically place 9 equidistant points on the curve. With CS6, it only places 3 points. Any way to get 9(or at least multiple) points placed?
I am working with vector art that has lines that either look like they were cut off and not finished out or extend to the edge of the page so they are straight when they should actually be curved.
Is there any way to take a straight line or part of an image and curve it with ease or will I have to redraw or alter each line?
I've just recently caught up to 2.8 (From 2.4 something or other believe it or not ) and amongst a couple of things I have to say I don't like is the fact that previously when setting a path, if I wanted it to be either perfectly horizontal or vertical I could see by the steps in the path preview line whether it was or not.
With the new version, initially at least, that's no longer the case. As I tend to work with straight lines a lot of the time it's proving to be a bit of a pain. Is there any way to set the path preview line to show the steps again to indicate a straight line.
I'm pretty new and have a simple problem that for some reason I can't figure it out! And that is how to make a series of lines on the image that are all perfectly horizontal or perfectly verticle. This will be part of a chart and the lines will be dividers. So the chart will have basically 21 rectangles with 3 rectangles across and 7 rectangles down.
So, I KNOW how to use the straight line tool to make the vertical and horizontal lines but I don't know how to keep the lines perfectly vertical and horizontal and parallel with each other!
I want to erase the watermark and x mark from a istock image for comping purposes. What is the easiest/fastest way to do this? Clone Stamp/patch tool? If stamp tool, how do you get the tool to delete the x line in a straight line. Mine always copys pixels next to it.
When I have a cdr file and need to save it as a plt file for my plotter the saved file has several little straight lines to make a curve instead of one smooth curved line. This didn't start happening until I upgraded to Corel Draw x4.
How to create a flow arrow label for a feature line that parallels the curve?
I've a vague notion that this could be done with a dynamic block and a few fancy expressions. I'm comfortable with expressions, but I've never used dynamic blocks at all, so I wouldn't know where to start.
To be clear, I know curved text is possible, but I'm looking for a curved line (ie an arc) that would look 'parallel' to the arc of the feature line (ie have the same centre point). This would have to be dynamic to allow for different radii and for flipping to the left and right side of the feature line.
If there is a command to split a line into segments? I know there is the divide command but that does not physically split the line, it just gives it points. i need the line to be seperate segments without the gap like the break command gives.
I've been trying to make a straight chain and make a curved one. I've tried the warp but it only distorts the links and become out of shape. How i would make it curved like the one in the diagram.
Trying to get evenly spaced line segments that lie on the circumference of a circle - every time I do the pattern repetition it gives me line segments the same length instead of constraining them to the circumference of the circle ?
In trying to learn more about label styles, the C3D Help instructs one to:
2. On the Layout tab of the Label Style Composer, select or create the label component that you want to span multiple segments.
3. In the Properties list, under General, change the Span Outside Segments property to True.Specify this setting for each component that you want to span multiple segments.
There is no "Span Outside Segments" to set to True in my Label Style Composer. The only T/F option under General is for visibility.
Civil 3D 2013 SP 1, 64 bit Dell Precision T5600, 16 GB Win 7 Professional 64 bit Intel Xeon @ 2.0 GHz NVIDIA Quadro 4000
Mastering C3D - the bit about spanning segments on an exterior line crossing several parcels. It works like the book shows except the crow's feet only appear at the start and end of the parcel's segment that I click on to insert the label, instead of the start and end of the whole segment. The distance the label reports is correct.
The crows feet are blocks inserted at the start and end of the direction arrow component (visibility false) in the author's style? I have turned the arrow's visibility on and can see that the arrow does not span the parcels.
I have another drawing in a later chapter on alignments that has the same spanning label style that works and I can't for the life of me discover the difference between the two.
Civil 3D 2013 SP 1, 64 bit Dell Precision T5600, 16 GB Win 7 Professional 64 bit Intel Xeon @ 2.0 GHz NVIDIA Quadro 4000
I am a first time Autocad user and have spent most of yesterday trying to work through this issue but am still not able to perform this. I have attached an image which on the lower part of the lines shows arcs with large radii which transition to parallel lines in the upper part of the image. Where the two meet there is an abrupt change in angle which I wish to have as a smooth transition from the gradual change in angle of the arcing lines to the parallel straight lines.
pic1.jpg
This is how the transition between the line segments should look.
Having a time getting ribs to align 2m below top of ridge beam, and connect to curved wall below. I created one, then arrayed, but the radius changes at each 2.5 degree interval. I don't think I should have to calculate the % radius change to get the beams to do this. Some constraint button maybe?
Not sure if editing a wall profile is the best way to model this, but it's working.
