AutoCad :: How To Assign Conduit Length Tag On Line
Oct 17, 2012How can i assign conduit length tag on line....? know that i have multiple lines and i wanna get total length of multiple line so how can i do this....?
View 5 Replies
ADVERTISEMENT
AutoCAD Dynamic Blocks :: Change Length Of Line Based On Length Of Attribute
Jan 8, 2013Is it possible to change the length of a line based on the length of an attribute?
I'd like to make the line a MINIMUM length of X" (I haven't decided how long yet--but know I'll need a minimum). But then after the user fills in the attribute, I'd like the length of the line to change to the length of the attribute plus a small amount (again, I haven't decided yet how much extra).
AutoCAD Dynamic Blocks :: Line Length Follow Content Length Of Attribute
Mar 16, 2012I was wondering if there is a way with DB's to have a line "follow" or "grow" with the content/value length of an attribute. Maybe some method of linking the attribute width to length of the line? Essentially, it would work just like turning on the underline setting when typing in mtext editor (or any program with an underline option for that matter), expect that the line could be placed anywhere, and would not have to reside directly below the text.
View 5 Replies View RelatedAutoCad :: How To Make Third Line Relative To Second Line So Angle Is 75 Degrees And A Certain Length
Oct 27, 2009I have been practicing using a older book(copyright 1990) and it has some decent exercises in it. I was able to do this one but it seems I can"t find the proper way to do this..First drawing a line a certain distance..ortho on,click the first point anywhere,move curser to the left and click again. that gives me a line at 180 degrees at what ever length..Line command again starting at the second point of the first line..after clicking that point,I type in @2.38<150 that gives me a line2.38 long at 150 degrees..now how do i make a third line relative to the second line so that the angle is 75 degrees and a certain length..the picture shows what I am trying to draw..using the polar cordinates you get an angle based off the UCS( which is set at world) when you try to draw the third line ..that makes the angle between line 2 an 3 not the angle that I want..To make the drawing,I rotated the ucs -30 degrees..But there has to be a better way than that..
View 9 Replies View RelatedAutoCAD .NET :: Define And Assign Variables In Single Line
Aug 3, 2012Why do most of the VB.Net examples, define and assign a variable in a single line as it is being used in the program.
In VBA I found it easier to read the code with the variables defined at the top of the function or subroutine.
What do most of you do when defining variables ?
I find the VB.net lines below more difficult to read ..............
For Each acSSObj As SelectedObject In acSSet
Dim acEnt As Entity = acTrans.GetObject(acSSObj.ObjectId,OpenMode.ForWrite)
AutoCAD Civil 3D :: Assign Feature Line Elevations From Points
Sep 13, 2013Given a feature line/polyline(FL/PL) and a series of points directly on the FL/PL, how can you assign the elevations of the points to the vertices of the FL/PL?
Without using a surface?
AutoCad 2D :: Assign Multiple Attributes To Single Line Text Within Block?
Aug 7, 2012If it is possible to assign multiple attributes to a single line text within a block, and be prompted for them upon insertion.
View 3 Replies View RelatedAutoCAD 2013 :: Won't Allow To Specify Length Of A Line
Jun 13, 2013I have used AutoCad for a few years and I installed 2013 to my laptop recently.I noticed that I couldn't specify how long a line should be. When I select the line tool and specify the base point and type how long it should be i.e. 3' and a red box appears around the dimension box and the line isn't drawn. I tried not specifying a unit of length and it draws the line just fine. But for some reason it wont complete the line if I specify feet or inches.
View 2 Replies View RelatedAutoCAD .NET :: Get Line Object Length
Dec 2, 2011Dim acDoc As Document = Application.DocumentManager.MdiActiveDocument
Dim acCurDb As Database = acDoc.Database
ed = acDoc.Editor
[Code]....
I need to get the line object length. i Have written the below code.
If i use area property i am getting zero.
AutoCAD LT :: AV Flows To Conduit Risers?
Feb 6, 2013I work for an A/V company. We use AutoCAD LT 2013. We are looking for a program or a computer script to check our A/V Flow Diagrams and Conduit Riser to make sure that all cables are accounted for.
View 3 Replies View RelatedAutoCad 2D :: Routine For Conduit Leader?
Mar 5, 2012I am running AutoCAD MEP 2012. Any basic routine for a conduit leader?
View 1 Replies View RelatedAutoCAD LT :: Using Symbol To Enter Line Length?
Dec 9, 2011I'm having a problem entering line lengths - something I remember occurring some time ago - but I can't' recall how I remedied it. The '@' symbol take time to register - instead of registering immediately as previously. I now have to check the command line each time and allow a moment for it to register before entering the values.
View 4 Replies View RelatedAutoCAD 2013 :: Length Of Line On Mouseover?
Dec 5, 2012In previous versions of autocad after I select a line, and put the mouse pointer over a vertex, there would be an on screen number displaying the length of the line. In Autocad 2013 this seems to have disappeared. how to get it back?
View 2 Replies View RelatedAutoCad :: Automatic Measurement Of Length Of Line
Sep 5, 2013I've recently re-install my AutoCAD on my Win7 PC and now whenever I try to draw a Line, there's this automatic measurement of the length of the line I'm stretching. It is really causing a lag on my PC for some reason and I seem to can't find a way to turn it off.
View 2 Replies View RelatedAutoCad 2D :: Control Length Of Dimension Line
Nov 15, 2013In Autocad 2006, is there a way to control the length of the dimension line when it extends outside of the dimension distance itself? In other words, when a dimension is small, and the arrowheads flip to the outside of the dimension parameter, the text and the extension line outside of the dimension seems to go to far outside of the dimension area..
Can I control how far outside of the dimension area that this line and text are placed? They seem to go to far out on my drawings. I prefer them to be closer to the actual dimension area instead of extending so far out.. Didn't know if there was a control for this and where to find it.
AutoCad 2D :: Control Dimension Line Length
Feb 28, 2013I have to flip out dimension lines/arrows all the time. How do I control the length of the dimension line when it is outside two lines?
View 1 Replies View RelatedAutoCad 2D :: Length Does Not Show Up During Drawing A Line
Nov 3, 2012I use Cad2013 . During a line command , I can not see the length beside the courser , so I have enter the length using keyboard and it is very time consuming .
I do not remember if I changed any default settings but It used to work properly .
Win 7-32 bit - cad2013 full version - no plugins - No viruses .
AutoCad :: Measure Length Of Continuous Line?
Oct 12, 2006Is there a tool where you just click on any line and it tells you how long the line is from end to end?
Basically I am drawing a curvy line that twists and turns here and there, but the line has to be less then so long. So I have to approximate the length by doing strait measurements and multiplying, it's really a pain.
I'd much rather just click the line, and it tell me how long it is from end to end, across turns and rounded edges and corners.
Revit :: Assign Keyboard Shortcut To Spline Line?
Aug 16, 2012When I draw the detail line (DL), Is there a way to switch from straight line to spline line quickly? It's difficult to keep moving the mouse to the toolbar to change the line type.
I tried to assign a keyboard shortcut to the spline line but it didn't seem to work.
AutoCAD 2010 :: Line Length Display Box Missing?
Oct 19, 2010I must have changed a setting and now I cannot figure out what I did.
On AutoCad at school, when drawing a line, there is a light blue dialogue box that would pop up above the cursor telling you the length of the line before you set it. (not the coordinates).
This is not showing up on the educational version of AutoCad I am running at home.
AutoCad :: Line Length Display On Endpoint Hovering
Feb 1, 2013So when i would select a line, hover over one of the endpoints, the length and angle would be shown, as a quick dimension. for some reason that has stopped, all it does now if i select the line, hover over an endpoint the only thing it says is stretch, or lengthen.
RANT!!! (come on 2013, thats stupid, stretch and lengthen are basically the same thing, dont you think if i stretch something it would automatically lengthen something, and if i lenghtened something, it in fact would also be stretching it. and to see you replaced the simple dimensioning of that line with a pointless i wouldnt call it option. now to figure out the length i have to keep the properties file open, or i have to draw a faux line over the current one just to check its length, or literally i have to draw a dimension line.) EnD!!
What option might have been turned off? and that the new array no longer gives you a box, but you do it all through the command line. or the dynamic input. That was an AWESOME box that i do miss dearly, and no longer have the option to bring back..
AutoCad :: How To Draw Line To Exact Coordinate And Length
Feb 2, 2012I would like to draw a line that is a specific length, lets say 16, that originates from a specific x,y location say 10,23, that terminates at exactly atleast the y coordinate 38. I don't care about the x or the angle.
View 9 Replies View RelatedAutoCad :: 3D Plane - True Length Of Line And Slope
May 18, 2005I have a plane defined from ucs-world points: (1,1,0),(3.6,2,1),2.2,3.6,2) .
It is intersected by the line defined by ucs-worlds points: (1.6,3.2,0.2) and(2.8,1.4,1.8 ).
Im having trouble trying to manipulate the UCS in order to find the location of the piercing point, the true length of the line and slope.
CorelDRAW Graphics Suite X5 :: How To Assign A Dotted Line / Outline
Apr 28, 2011I would like to mark the outline of an object with a dotted line/ the outline should be a dotted line to show that this object can be cut out. But I see only where to choose the thickness of a line.
View 1 Replies View RelatedAutoCAD Visual LISP / AutoLISP :: Line Length To Attribute Tag
Sep 30, 2013Is there any simple code for to sum length of lines which is i am choosing and copying result to chosen attribute tag ?
View 1 Replies View RelatedAutoCAD 2010 :: Draw A Line Without Length / Angle Showing As To Go?
Feb 15, 2012How do you draw a line without the line length/angle showing as to go?
View 6 Replies View RelatedAutoCAD Civil 3D :: Surface Style - Line Component Length
Jun 20, 2013I have surface style (could be slope or spot elevation) with a 2 line component, and text component above and below the line. I'm trying to create on style for many options. I'm using c3d 2013, but moving to 2014.
I would like to do the following after placing the label:
1. adjust the length of the line component. (ex: as I rotate the lable, the length of seg 1 changes )
2. turn off one of the line component
3. adjust the angle of one of the line component.
4. when drag, the length of the line changes to a new value.
and while I'm asking, is there a way to move/rotate/drag the syle to a percise distance. I want the leader to be 1 unit long at 30 degree angle.
AutoCAD Civil 3D :: Block Constraints - How To Hold A Line To Txt Length
Jan 15, 2013I am using Civil3D 2012 SP 2.
I am creating a block for my details. I want to be able to title my block and the the line under my txt will change it's length based on the lenght of the text. I keep playing with the constraints, but I haven't found one that is doing what I want.
AutoCAD Civil 3D 2012 SP4
Windows 7 (64)
AutoCAD Map 3D :: Build Annotation Template To Display 2D Line Length?
Jul 25, 2012When building an annotation template, in the block editor (annotation editor etc..); how do you take the length of a 2D line or pline to be the display of my template?
Doing a water system map and it would be nice to have a line length with the ' symbol at the end rounded to the nearest foot on each length of pipe.
AutoCAD Visual LISP / AutoLISP :: Line Length Report
May 30, 2013I am trying to create a report of line lengths based on linetype.
I have built a list that looks like this...
(("CUT4SS" . 859.566) ("CUT4SS" . 862.231) ("CUT4SS" . 927.651) ("CUT6SS" . 1158.48) ("CUT6SS" . 509.903) ("CUT6SS" . 2840.31) ("CUT4SS" . 967.76) ("CUT4SS" . 508.73) ("CUT4SS" . 111.065) ("CUT4SS" . 483.216))
I want to take this list and create a function to create a list of total lengths i.e. the CDR's.
(("CUT6SS" .total length)("CUT4SS" . total length))
AutoCad 2D :: Any Command That Actually Splits A Line Into 3 Equal-length Lines?
Jan 23, 2014I have a line that i would ideally like to divide into 3 equal segments. The divide command places points along the line, but I can't snap to them.
I know that I can place a block at each point which I could snap to, but is there a way of doing it without creating a block? Also is there a command that actually splits a line into 3 equal-length lines?