I have a line and an arc which are offset to each other. How do I fillet between the arc and the line. Every time I try to do it, it doesn't give the solution I want. I have attached a file which will show you what I mean. I want to fillet between the horizontal white line and white arc with a unit size of 6 so that the result is as shown by the red arc.
View 9 Replies
Autocad 2012 LT. I can't fillet between an existing line and arc. The line's start Z is 0 as well as middle and end are 0. The arc is the same....but still it says they are non coplaner and will not fillet.
In another area of the drawing, I draw an arc and a line and they will fillet just fine..... This is weird....
I have gone back in to the properties and even though the say that the Z is 0, I type "0" in again and then it will fillet.....
I have a little issue with drawings where I cannot find out how to highlight fillet edges on the models. I dare say I am missing some simple setup option.
The picture attached shows what I mean. The left is how the model looks in drawing mode and on the right is how I would like it to look (taken from the modelling environment).
I have a lips that creates a zero radius fillet.
(defun c:FZ () (setvar "FILLETRAD" 0)(command "_.fillet" "multiple"))
This works great.I would like to expand this by turning the line into a polyline..
Fillet works fine on a single curve and straight lines, but I'm having trouble using the fillet command on two curves (arcs). I have two circles which I have trimmed into arcs roughly to the correct length, when I try to fillet them (with various radii) the filleted curve either connects to the wrong end of one of the existing curves, or the filleted curve curves in the wrong direction. I've used this tool a lot before and have never had problems - until now. Is there a way to decide which way the fillet curves?
View 8 Replies View RelatedHow to fillet a 3D polyline with AC2012?
OR
How to automatically set the corner bend radius of a sweep along a 3D polyline?
The attached image shows what I did in a different program, but need to repeat with AC. The swept 3D object is moved off its path in the attached image.
I'm having a problem with the fillet command using a radius, I can't seem to get a rounded corner. I have the radius set at 1.00. I should see a rounded corner. If I set it at 0.00 or 1.00. I get the same result. Something doesn't seem right! Could it be a setting.
I viewed a few videos on Youtube and I can't replicate the same filet with radius results. I watched one that you can select radius by right clicking mouse. A text box appears to the right of the cross hair cursor where you can input the radius. On my screen that does not come up.
How to set chamfer and Fillet. I have tried but just can not get it to do anything.
I may have maladjusted some other setting. Operator error for sure. I do not need to use these functions for anything else but the 3 shown in the attachment.
i cant fillet the r21 circle
View 9 Replies View RelatedI would like to fillet a box, which has already been filleted, with a radius of 3, but cannot seem to get it working.
See attached.
I am currently running acad 2009.
I have AutoCAD Map 3D 2013. Sometimes the fillet preview doesn't work. The fillet preview is supposed to work like this:
After setting the radius of the fillet, click on one line.
Move the cursor to other line to be filleted and wait for the preview of the fillet to appear. If the preview of the fillet looks good, click on other line to create the fillet. If the preview of the fillet doesn't look good, change the radius of the fillet and try again.
I think that there is a variable that needs to be set.
I need to fillet below lines in .net...Iam having the entities list..How to fillet those lines with radius using .net?
View 2 Replies View RelatedI have remodeled a part I was working on previously, but now an edge doesn't want to fillet, as it was on the old model ( in the top right corner )..
View 2 Replies View RelatedI created a rectangle using draw line (i am working on Autocad 2010). Now I want to create 4 fillets at each corner with some radius using vb.net.
View 8 Replies View RelatedIs there a way to put a FILLET radius in a polyline? (2D dwg)
e.g. a straight line crosses a radius, both lines trimmed off, turned into a polyline and joined using PEDIT.
When I try to put a FILLET radius between the straight line and the original radius, the command line quotes;`Cannot fillet polyline arc segements'
How to fillet a 3D polyline with AC2012?
OR
How to automatically set the corner bend radius of a sweep along a 3D polyline?
The attached image shows what I did in a different program, but need to repeat with AC. The swept 3D object is moved off its path in the attached image.
How do I create a concave fillet in AC2012?
Usually, when I try to fillet one edge it creates a convex fillet. and if I want it to be concave instead?
I'm trying to fillet the edge of a 3d solid guitar body and can't seem to make it happen.
See attached file.P Bass - Copy.dwg
How can i change the radius og the command fillet in autocad mechanical 2011?
View 2 Replies View RelatedI am working on my project at home and I am having some problems with the fillet tool.
Attached is a picture of my problem with what it is doing.
I am trying to fillet A to E and E to C (B to D and D to F also)
On the left hand side when I fillet, it connects C to E instead of A to C and I do not know why it is doing that or what I am doing wrong.
How do i make the 3mm fillet go in the other direction.When i apply the fillets to the top of the pipes it goes inwards but i want the fillet to go outwards.(like a weld - i don`t want to weld though just use a fillet).
View 1 Replies View RelatedIs there a way to create smooth transitions for fillet welds for around corners?I have to create four separate fillet welds on all sides of the mating pieces and it breaks at the corners.
View 2 Replies View RelatedWhat kind of fillet i need for relax the edges in a eccentric reducer pipes's fitting, i can use fillet of faces for the sircular edge smaller , but am in troubles with the bigger .
View 1 Replies View RelatedI am used to entering my fillet radius dimensions in the command line with [F]illet, [R]adius, then entering a value.
However with 2014 an extra prompt has been added (or enabled) which would mean the path was [F]illet, [D]imension, [Radius], value. I was getting frustrated with this and tried fiddling with the settings ([F]illet, [S]ettings) but could not sort it, and now when I do go to enter a dimension the only option I am left with is to "Select fillet arc", meaning I have lost the ability to enter a value in the command line.
How do I regain the ability to enter a numerical value for a radius?
I am working on a project for an autocad class and have run into a snag. I have to fillet a box but the rounded edge is on the inside instead of being on the outside. I'm attaching a screen shot of a 2-d version and the 3-d I have so far.
View 3 Replies View RelatedI have a problem I am using Autocad lite 2011 and need to draw if you can picture a column with a 15 mm deep fillet 42 mm wide which has a ramp and twist applied to it spiraling all the way up it. How do i go about this.
View 9 Replies View RelatedHow can I Create inverted fillet drawing describes the required
fillet.jpg
I want to put a 5 mm radius fillet on the upper edge. After 1.5 mm it will not...Why? What can I do? Convert it to a mesh object? Or?
View 9 Replies View RelatedWe are trying to apply a chamfer / fillet, anywhere betwen 0.5mm - 1.00mm, to the attached ACAD 2004 / ACAD 2012, 3D model, along the edges connectiing from the existing chamfer / fillet, up each side to the top - where you will see there is no chamfer / fillet - (the outside of the cup profile,Attachment 34929 Attachment 34928not the inside of the cup profile).
That resolved the problem, the software struggled a bit with filleting till we tried a smaller degree, then it worked - we thought it would automatically fillet (flow) in / out according to what dims were available.
I have a problem with a Fillet. Im drawing a 2D chair and when i want to use a Fillet its drawing a 3D ...
View 2 Replies View RelatedACA 2013: We have notice that autodesk has added a quick preview for fillet and offset. It shows what the fillet is going to look like or what the offset is going to be. Is there a way to turn this off?
View 3 Replies View Related
