AutoCad :: Can't Fillet Between Existing Line And Arc - Non Coplaner
Dec 14, 2012
Autocad 2012 LT. I can't fillet between an existing line and arc. The line's start Z is 0 as well as middle and end are 0. The arc is the same....but still it says they are non coplaner and will not fillet.
In another area of the drawing, I draw an arc and a line and they will fillet just fine..... This is weird....
I have gone back in to the properties and even though the say that the Z is 0, I type "0" in again and then it will fillet.....
View 1 Replies
ADVERTISEMENT
Mar 21, 2007
I have this routine for using a selected arcs rad value as a new fillet rad. If you like, a "match fillet" routine:
;Fillet Copy
;Copies the Radius of an Existing Fillet or Arc;
(defun C:filletcopy ()
(setvar "cmdecho" 0)
(setq c1 (entsel "
Select Fillet to Copy:"))
(setq c1 (entget (car c1)))
(setq rad (cdr(assoc 40 c1)))
(setvar "filletrad" rad)
(princ "
Select Lines:")
(command ".fillet" pause pause)
)
I use the routine loads but could modify so it would pick up the value of a filleted polyline? As it stands it can only select an individual arc. I would like the routine to be able to pick individual arcs and/or filleted polylines, without exploding first, if possible....
View 9 Replies
View Related
Mar 26, 2012
I have a line and an arc which are offset to each other. How do I fillet between the arc and the line. Every time I try to do it, it doesn't give the solution I want. I have attached a file which will show you what I mean. I want to fillet between the horizontal white line and white arc with a unit size of 6 so that the result is as shown by the red arc.
View 9 Replies
View Related
May 6, 2013
I have a little issue with drawings where I cannot find out how to highlight fillet edges on the models. I dare say I am missing some simple setup option.
The picture attached shows what I mean. The left is how the model looks in drawing mode and on the right is how I would like it to look (taken from the modelling environment).
View 1 Replies
View Related
Jan 18, 2013
I have a lips that creates a zero radius fillet.
(defun c:FZ () (setvar "FILLETRAD" 0)(command "_.fillet" "multiple"))
This works great.I would like to expand this by turning the line into a polyline..
View 3 Replies
View Related
Sep 12, 2013
For example, I'm making revisions to a plan and drag a block or xref of the floor plan changes where walls/doors/windows have moved. I want to be able to simply pick the underlying linework as opposed to tracing over each line of said xref/block.
View 8 Replies
View Related
Jun 10, 2011
Basically I got a process which is quite long , let's say 30 seconds.
I want put a counter at command line showing to
user how many objects has been processed so far. But I don't want to use New Line Feed to change the line and keep each new number at same line and same location of command line.
View 2 Replies
View Related
May 2, 2011
How do I to set and to see or show the existing grips point when drawing new line?
View 8 Replies
View Related
Jan 11, 2013
i have a corridor. the corridor feature line that is supposed to hit the proposed centerline is following my existing grade instead of where the profile is. in other words, the corridor line i need at the centerline when i do "feature lines from corridor" is following my existing grade instead of the top of my road. did i accid. change something? i need it to follow the top centerline of my road. the red arrow is the line i need at the top centerline.
View 3 Replies
View Related
Sep 20, 2011
I am currently using Architecture 2012. When I go to draw a line or an object like a wall or door I can select the colour from properties before I draw the object. The object will then come out that colour.
However if I need to change that colour at a later point, but how to do this?
View 7 Replies
View Related
Dec 15, 2013
I don't undrstand why my assembly line increased after the existing surface in cut and fill condition, it should be stop at the existing surface. due to this problem my cut and fill quantities is not coming accurate. I'm attaching the screens shot of section. I'm using civil 3d 2009 32 bit software.
View 4 Replies
View Related
Aug 2, 2012
I have an existing surface with a steep slope and a feature line for the edge of a proposed walkway. I need a buffer of 25m on either side of the walkway but offsetting doesn't take the grade of the slope into account. How do I grade down the hill from the feature line at 25m to match to the existing surface?
View 3 Replies
View Related
Jun 4, 2013
Can I modify an existing viewport in a macro or in the command line?
Using a macro, I want to modify (specifically delete) the viewport from a layout tab after chspace from model space.
I have LT so no LISP. qselect works but cannot be put into a macro.
If I "select all" on a layout tab in paperspace ACAD says 1 of the objects selected is the viewport so I know autocad recognizes the viewport as a different kind of object.
View 6 Replies
View Related
May 15, 2012
While I was out, my partner somehow now has two existing ground lines in my cross-sections. ####exist and ####exist (1). They are offset by about .5 feet left to right. Where do I remove the surtface ###exst (1) from the cross sections. I am looking now.
View 2 Replies
View Related
Nov 18, 2013
[URL]
Bring that back from the archives... because I am still very fond of redoing hundreds of cross sections because you're incable of redistributing the graphs when a sample line is added to a an existing group... and blow up all of the projections well done.... way to leave out a super critical dynamic component.
PPD E P I C F A I L
There is some unbelievable gaps in the software but how do you let this one go on for so long?
Dell Precision T3500 - Xenon W3550 @ 3.07 (4 core)
Ram @ 12Gb
64bit Win7 Pro
Samsung SSD
NVIDIA Quadro 2000 - Dual Monitors
Cat 6 network with GlobalScape Avail Agent - WAFS
Infrastructure Design Suite Premium and Civil 3D 2012
View 1 Replies
View Related
Apr 1, 2012
Any way to convert all of the single line text in exisitng drawings to multiline text without having to do them individually in Civil3d.
View 2 Replies
View Related
Jun 19, 2011
I have an image which is similar to a white spider's web centred on but slightly rotated to a red spider's web on a solid background. I want to delete the solid background so it appears transparent and delete the white web so all that is left is the lines of red on a transparent background. I used the Magic Wand and Global flood mode to remove the white web and background but the red lines are very thin and broken now.
Is there any easy way to just nudge the thickness up enough to make them more solid? Or is there a plug-in that can do this? I am using v3.36.
View 6 Replies
View Related
Jan 4, 2013
How can I draw a line from the endpoint of an existing line (snap to grid is on), without the lines being joined? Joining causes two problems for me:
1. The arrowhead at the end of the existing line moves to the end of the joined line, whereas I want the arrowhead in the middle of the combined line.
2. Even without entering isolation mode the new line gets joined to a line which belong to a group, thus becoming part of that group as well. This defies the use of grouping to create logically connected units.
View 4 Replies
View Related
Mar 28, 2013
I made a long line with a complex stroke profile. I decided to remove a section, but it distorts the new ends with the excess profile. How can I delete a mid point on a line and keep the profile visually intact?
View 5 Replies
View Related
Sep 28, 2012
I'm trying to create an all new existing surface over existing ground. I have a TIN surface of the EG, and I have drawn overlay splines that describe the new surface, but how to go about creating that design surface.
It is a compound surface, open on one end and closed all around on the other, somewhat like a half of a football stadium, but with an irregular upper edge because I am needing to figure out cuts and fills to manipulate the EG into this new surface without costly major terraforming. There is about 40-50' vertical elevation between the "field" and the upper rim with a generally constant 7-10 deg. slope all around. I'm just at a loss to figure out how to approach this project, and am quite new to Civil 3D.
Civil3D 2013
MacBookPro 17 - 2.4GHz Intel QuadCore i7 (Late 2011 build)
Microsoft Windows 7 64bit
350GB Bootcamp volume
View 2 Replies
View Related
Feb 3, 2013
Fillet works fine on a single curve and straight lines, but I'm having trouble using the fillet command on two curves (arcs). I have two circles which I have trimmed into arcs roughly to the correct length, when I try to fillet them (with various radii) the filleted curve either connects to the wrong end of one of the existing curves, or the filleted curve curves in the wrong direction. I've used this tool a lot before and have never had problems - until now. Is there a way to decide which way the fillet curves?
View 8 Replies
View Related
Sep 18, 2011
How to fillet a 3D polyline with AC2012?
OR
How to automatically set the corner bend radius of a sweep along a 3D polyline?
The attached image shows what I did in a different program, but need to repeat with AC. The swept 3D object is moved off its path in the attached image.
View 7 Replies
View Related
Nov 12, 2012
I'm having a problem with the fillet command using a radius, I can't seem to get a rounded corner. I have the radius set at 1.00. I should see a rounded corner. If I set it at 0.00 or 1.00. I get the same result. Something doesn't seem right! Could it be a setting.
I viewed a few videos on Youtube and I can't replicate the same filet with radius results. I watched one that you can select radius by right clicking mouse. A text box appears to the right of the cross hair cursor where you can input the radius. On my screen that does not come up.
View 9 Replies
View Related
Mar 6, 2012
How to set chamfer and Fillet. I have tried but just can not get it to do anything.
I may have maladjusted some other setting. Operator error for sure. I do not need to use these functions for anything else but the 3 shown in the attachment.
View 2 Replies
View Related
Mar 7, 2013
i cant fillet the r21 circle
View 9 Replies
View Related
Jun 28, 2011
I would like to fillet a box, which has already been filleted, with a radius of 3, but cannot seem to get it working.
See attached.
I am currently running acad 2009.
View 4 Replies
View Related
Nov 15, 2012
Some background: We have a composite surface of existing surveyed contours as a TIN pasted into existing aerial contours that we received from a client. We used polylines to generate our proposed contours, and then generated a proposed surface from that. We've made a blank surface, pasted in the existing surface, and are trying to paste in our proposed surface... only the existing contours outside of the proposed suface no longer line up correctly once we do.
We've tried applying the method laid out here: [URL] ........ (and the link referenced in the bottom) but are still having trouble getting the surface to work. We've tried offsetting as little as 0.25' and as much as 5' with the feature line draped over the existing surface, but it seemed that the greater the offset, the greater the discrepancy.
Just to make sure we even tried that correctly - should the breaklines that we add be standard or non-destructive? (I've tried it both ways with little success either way, so I don't know if it matters much in this instance, but perhaps for future reference it would work.)
I've attached a screen shot of our surfaces. The pink and green lines are the proposed contours, the white dashed are the existing. The outer red line is offset 0.25'. As I've mentioned, we've tried offsetting various amounts with decreasing success.
View 9 Replies
View Related
Jul 14, 2013
I have AutoCAD Map 3D 2013. Sometimes the fillet preview doesn't work. The fillet preview is supposed to work like this:
After setting the radius of the fillet, click on one line.
Move the cursor to other line to be filleted and wait for the preview of the fillet to appear. If the preview of the fillet looks good, click on other line to create the fillet. If the preview of the fillet doesn't look good, change the radius of the fillet and try again.
I think that there is a variable that needs to be set.
View 3 Replies
View Related
Dec 23, 2013
I need to fillet below lines in .net...Iam having the entities list..How to fillet those lines with radius using .net?
View 2 Replies
View Related
Feb 19, 2012
I have remodeled a part I was working on previously, but now an edge doesn't want to fillet, as it was on the old model ( in the top right corner )..
View 2 Replies
View Related
Jan 12, 2010
I created a rectangle using draw line (i am working on Autocad 2010). Now I want to create 4 fillets at each corner with some radius using vb.net.
View 8 Replies
View Related
