I have a drawing I want to plot to 1/8" Scale. I'm drawing at 1:1 scale and When zooming in to draw my line weights look accurate, however when I zoom out to view my whole drawing lines are to thick/blotchy and shapes are distorted. I've played with plot styles, dimension styles and my line weights ... nothing seems to solve this. I believe it has something to do with the size of my drawing.
I attached a drawing.
I am working on automating page setups in model space and am looking for a way to set the plot scale equal to the annotation scale for scaled drawings with
(setvar "filedia" 0)
(setq a (getstring (getvar "cannoscale")))
(command "-plot" "YES" "MODEL" "" "" "" "" "" "" !A "" "" "" "" "" "" "_Y" "_N")
Setting the plot scale with !A causes the lisp to fail. However, when running each prompt through the command line individually, !A works fine. what is missing?
I have a block that i would like to scale based on the plot scale when plotting.
We set up our drawings full size and occasionally we want to plot them at half size. We do this by setting the plot scale to 1:2 (custom) in the plotting dialog. We have a few blocks that we want to print at the same size on paper, essentially become twice as big.
Is there is a way to fix the size or just set a few scale states and have them automatically adjust based on the plot scale (not drawing/annotative scale)?
I work in autocad 2010 and I draw in scale 1:1 . What an annotation scale is, moreover I have never used annotative objects in my drawings.
Nonetheless, when I try to plot a drawing, while I am in the model view, I choose the scale in mm/units, I select the plot area and when I press preview or plot, I get the message THE ANNOTATION SCALE IS NOT EQUAL TO THE PLOT SCALE. DO YOU WANT TO CONTINUE?
I press yes, I print it and the outcome is always a bit smaller than it should be.
When i am in the layout mode and I try to plot, I dont get this message. But I dont know how scaling works in this case. For example I want to plot in a A4 paper, scale 1:100. So I type 1000mm/100units, as I did in the model mode, but the result is wrong.
I do warehouse layouts: circles, squares and rectangles. I don't know a thing about these scales.
I get this message when i try to print D-size drawing. Received this drawing from outside source and need to print.
How to plot my drawing in scale.. i always print in A3 and A4 size paper. i wanted to know how to do this.. ex.. 1:100 , 1:200, etc. 2nd:
Here is the scenario.: i have an forwarded drawing then i wanted to print/plot it in scale of 1:100 it is possible to do that?
I am using autoCAD 2011. I have a problem. If I do a drawing in autoCAD in mesarments that they should be in real life. For example if wall is 9000mm long I type in 9000. Building plan like that is easier for me. But problem comes when I try to plot it to scale 1:100 for ISO A3 paper (420x297) How Can I make it fit perfectly and be in-scale?
And another question. If I want to have a frame around my drawing and corner frame with name of the work, who did it etc etc. so I don't have to do it over and over again on every single new drawing. How can I do it? I heared I can use blocks. But how do I fit my block to a certain scale? If I make my block in 420x297 which is A3 standard and do a drawing with 1000- mesarments than it simply will be small for it.
where should i set the scale in the page setup manager or in the layout after i double click on the viewport i get the scale in right corner.
and iam working on the metric units.
I don't know how to plot/scale from layout. I have drawing in model that wont show in layout. Drawing is in scale 1:1 in mm. i have to plot it on 36" paper in scale 1:500. I saw someone scaling it with commands something like, z-s-1xp, an ucs.
View 9 Replies View RelatedI have several dxf files that were provided for laser cutting purposes. I have attached one file as an example. I am able to open the file and choose layout 1 and print. If I choose a 1:1 scale the image is very tiny in the corner of the page. If I leave the settings alone and just print, it is a full page, but the part on the paper is not the correct dimensions. The dimensions are in the gif file I also attached.
When I print the dxf file the gap between two of the holes, for example, that should be 70mm is actually like 95 or so. I have acad lt 2004 but also trueview 2011.
I have a problem when I am trying to plot auto-cad drawing. I have tried to set the scale in layout to 1/8" : 1' and I create a page set up and choose 24x36 paper size then when I try to print leaving the scale at the printer window to be 1:1 but when I press preview to see how the plot going to be, the drawing became very small at the lower left corner of the paper.
View 9 Replies View RelatedAm configuring many page setups and when printing/plotting there is a checkbox to scale lineweights. Was wondering what the consensus is on this. Should the check scale line weights box be checked, or not?
View 5 Replies View RelatedI'm trying to plot a set of drawings that need to be set at 1:1. Every time I pick Custom or 1:1 and set it to 1mm = 1unit, AutoCAD immediately switches it to whatever 1:1_6 is, leaving me with a bunch of empty space around all my viewports.
I'm fairly new at using paper space, and I've never used a plot scale that have underscores in them, so I don't even know what they're representing.
Could we can use 1 ctb file for all drawing scale? The problem is the lineweight at 1:100 is OK but at 1:5 it is quite light.
Could we use scale lineweght?
Is there a way to scale from D size to E size when creating a pdf?
View 4 Replies View RelatedI am trying to plot a map at on 24 x 36 paper and keep it to scale. It appears I have all of the correct settings including 1"=1', fit to paper is unchecked, etc. My print preview comes across correctly but when I go to plot a message appears in the command line stating
Effective plotting area: 26.00 wide by 18.00 high
Effective plotting area: 13.63 wide by 6.22 high
Plotting viewport 2.
Effective plotting area: 13.77 wide by 6.25 high
Plotting viewport 3.
Plotting viewport 1.
The plot then comes out on paper way larger then 24x36 and the area plotted is limited to the 13.77 x 6.25. My co-worker opened the drawing and printed it to scale on 24x36 no problem. What gives? I cannot find a setting to get it to plot correctly.
Why in some of my drawings I am not able to select the "scale lineweights" check box in the plotting dialog? I am using 2002. I can't seem to find any differences in these dwgs?
View 2 Replies View RelatedI'm using 2004lt- I have current .dwg in modelspace and set up to plot in PS@ 3/23"-1'-0". I'd like to create a second set of PS tabs to plot portions at 1/4"-1'-0" on the same border when needed.
In its a single viewport in MS and PS the current scale is 1:1 but if i change it to 1/4"-1',etc the plot preview appears wrong
Plot scale / Annotation scale / Viewport scale
I couldn’t figure out how these three types of scales are correlated with one another. For example, my drawing unit in AutoCAD is meter. And thus if I need to print my drawing with a scale of 1:200 then I set the annotation scale to be 1:2viewport scale to be 1:2plot scale 100:1000
if I need to print my drawing with a scale of 1:20 then I set the annotation scale to be 5:1viewport scale to be 5:1plot scale 100:1000
I couldn’t derive the rule that controls these three types of scales. This is also quite confusing when working with C3D! Sounds not the same logic is applied.
I am working on an AutoCad drawing (Vers. 2013) that I got from someone else. I am setting up my drawing and right clicked my sheet tab as usual to go to the page set up manager. I set up my printer, ctb, paper size etc. But when I try to set my plot size to 1:1 it won't retain it and reverts to 1"=1'. It will however let me switch to anything other than to 1;1 (ie 1:10). I checked some existing drawings and the problem doesn't show up. So it's just this particular drawing that's messed up. I checked my drawing units and drawing setup commands and they are the same as I always use.
So the question is why won't let me use a plot size of 1:1?
I have recently started working on a project in metric and have a weird (to me) issue when I try to plot. There are literally hundreds, of scale options in the Scale popup, most of which make no sense to me. I know that I need 1:25, or 1:100 to fit on the page I am printing to. How do I remove or filter out all of the others such as 1:100 3_1_1_1_1_1? I don't even know what that notation means.
View 9 Replies View Relatedwhy when i try to plot a scale drawing my profile loses it scaled size and all texts and images are huge.
See attached.
Doc1.pdf
why the drawing plots results using the viewport scale in the layout is not accurate?
View 1 Replies View RelatedI have one drawing per file at model tab. When I need to plot a multiple page file, I use:
Print > Batch Plot.
The problem is that I have to set plot configurations ( plot style table, plot area, paper size, etc) in each file before use Batch Plot.
Now I received 722 files with a wrong Plot Style Table. For this time I change the associated *.ctb file at Plot Style folder, but I will need to associate the right *.ctb to each drawing. It's also common to have to change other properties.
I am a Mac user and new to AutoCAD. I am enrolled in a CAD class this semester and the instructor for my session is requiring Windows. Supposedly this is because AutoCAD for Mac does not allow for proper printing on their plot style setting.
I understand that I can install Bootcamp and Windows on my computer, but I'd really like to avoid that if I can. If I were to do my work on my Mac and then digitally transfer my files to a PC for printing purposes, would my files become corrupted or compromised in any way?
Where else do they keep this setting? I only have found it in Active Layout in extended dada
(entget (vlax-vla-object->ename(vla-get-activelayout (vla-get-activedocument(vlax-get-acad-object)))) '("*"))
The last pice of extended data is:
("PLOTTRANSPARENCY" (1071 . 0))
When i change it to 1
(setq layout(vla-get-activelayout (vla-get-activedocument(vlax-get-acad-object))))
(vla-getXdata layout "PLOTTRANSPARENCY" 'type 'data)
(vlax-safearray-fill data '("PLOTTRANSPARENCY" 1))
(vla-setXdata layout type data)
it stays there (extended data), but the setting in Plot dialog box doesn't change!!! And it still prints no transparency.
It takes to save the drawing and reopen it again to see the change.
The command -PLOT does not have this setting as well, so my options back to VBA or Lisp, but HOW?
I have a problem to plot thin lines and dots when Plot Transparency option is On in the Plot dialog box.
The lineweight is a half of the original. I think i have tried everything.
It shows correctly in the Plot Preview but when printed there are no dotted hatches and lines are much thinner.
Can users with a 64 bit computer share pc3's and pmp's with 32 bit users without adverse effects?
View 1 Replies View RelatedWhen I publish a drawing as a multipage DWFx (or PDF for that matter) with "Include Layer Information" selected, the Plot Stamp (Simple Date/Time and Text) comes out but on different layers on different layouts.
Example:
First Layout : Plotstamp resides on Layer 0
Second Layout: Plotstamp resides on Layer 3P
Third Layout: EQPT-VC
etc
Some general information:
Autodesk AutoCAD 2011 64bit
Autodesk DesignReview - 2012
Adobe Acrobat X Professional
Layer 0 Is thawed/plotable and on in all layouts, viewports all layers, viewports. It has at least one entity per layout
Is there anyway to rectify this and still use the built-in Plot Stamp?
So the firm I work at has AutoCAD 2000 and 2007. 2000 is installed on 5 out of the 7 computers, and 2007 installed on 6 of the 7 computers. 2 of the computers running just ACAD 2007 are Windows Vista, while all the other computers are Windows XP. We have an OCE TDS320 CAD Printer, an HP Wide Format Printer and a Panasonic 330 Copier/Fax/Printer. Our Problem is that When you try to plot an ACAD2007 drawing it will only plot it in color. This problem did not exist before 1/12/12.
When I select the Plot Style to print I select "monochrome.stb" which has always worked, now all of a sudden it doesnt. The only way i have found to fix this problem is to change my drawing to layer "0" which is white, so when it tries to print in color it will print black. Another Guy in the firm i work at has ACAD2007 on his computer running XP, he also has 2000 running on the same computer. When he tries to plot on ACAD2007 the same thing happens, so it is not isolated to my computer.
There is a difference though between his Plot Styles on his computer and the ones on mine. His end with .ctb, which works. It only doesnt work when he tries to print a drawing i made off of my computer. Because of this we copied his Plot Style folder for AutoCAD 2007 and installed it into the folder with all of my plot styles on my computer, replacing the ".stb" with ".ctb" That did not work at all. The last thing we tried was to copy over a file that plotted correctly, delete the drawing and draw what we needed, This also did not work. So basically we are thinking that ACAD2007 is not reading the Plot Styles correctly, or the Plot Styles are wrong or currupt.
I have several objects on various layers in model space and they are exposed through a viewport in a paperspace layout. I also have a corporate CTB plot style.
Here is my problem: If i plot the objects from model space, they all plot with the correct lineweights as defined in our corporate CTB, but when i plot them from the paperspace layout, some but not all objects plot with a heavier lineweight than what is defined in the CTB.
I thought the CTB was supposed to override any settings applied to individual objects, but more importantly, why the different results, on the same objects, depending upon the space from which they're plotted?