How to plot my drawing in scale.. i always print in A3 and A4 size paper. i wanted to know how to do this.. ex.. 1:100 , 1:200, etc. 2nd:
Here is the scenario.: i have an forwarded drawing then i wanted to print/plot it in scale of 1:100 it is possible to do that?
I have a problem when I am trying to plot auto-cad drawing. I have tried to set the scale in layout to 1/8" : 1' and I create a page set up and choose 24x36 paper size then when I try to print leaving the scale at the printer window to be 1:1 but when I press preview to see how the plot going to be, the drawing became very small at the lower left corner of the paper.
View 9 Replies View Relatedwhy when i try to plot a scale drawing my profile loses it scaled size and all texts and images are huge.
See attached.
Doc1.pdf
why the drawing plots results using the viewport scale in the layout is not accurate?
View 1 Replies View RelatedI am working on automating page setups in model space and am looking for a way to set the plot scale equal to the annotation scale for scaled drawings with
(setvar "filedia" 0)
(setq a (getstring (getvar "cannoscale")))
(command "-plot" "YES" "MODEL" "" "" "" "" "" "" !A "" "" "" "" "" "" "_Y" "_N")
Setting the plot scale with !A causes the lisp to fail. However, when running each prompt through the command line individually, !A works fine. what is missing?
I have a block that i would like to scale based on the plot scale when plotting.
We set up our drawings full size and occasionally we want to plot them at half size. We do this by setting the plot scale to 1:2 (custom) in the plotting dialog. We have a few blocks that we want to print at the same size on paper, essentially become twice as big.
Is there is a way to fix the size or just set a few scale states and have them automatically adjust based on the plot scale (not drawing/annotative scale)?
I work in autocad 2010 and I draw in scale 1:1 . What an annotation scale is, moreover I have never used annotative objects in my drawings.
Nonetheless, when I try to plot a drawing, while I am in the model view, I choose the scale in mm/units, I select the plot area and when I press preview or plot, I get the message THE ANNOTATION SCALE IS NOT EQUAL TO THE PLOT SCALE. DO YOU WANT TO CONTINUE?
I press yes, I print it and the outcome is always a bit smaller than it should be.
When i am in the layout mode and I try to plot, I dont get this message. But I dont know how scaling works in this case. For example I want to plot in a A4 paper, scale 1:100. So I type 1000mm/100units, as I did in the model mode, but the result is wrong.
I do warehouse layouts: circles, squares and rectangles. I don't know a thing about these scales.
I get this message when i try to print D-size drawing. Received this drawing from outside source and need to print.
We do most of our drawing in 2D – quaint I know, but that’s the way the office works. On occasion we’ll do something as a solid model to guide a client understand a complex roof or a clearance problem. We started a model for a project we are working on and ended up using it as building elevations.
The problem is with plotting. If I use our standard office CTB (which is set to print as black), I get color printouts no matter what I try. I have tried using an STB and changing all our layer colors to “7” in an attempt to make it print black, but I'm getting extremely undesirable - seemingly random - line weight results.
The client wants the next project done in 3D as well and I’d like to be able to have the elevations look right.
Is there a way to apply plot styles and line weights to a dwg file like 'dwf ePlot' does but keeping the results in .dwg format?
View 4 Replies View RelatedAutoCAD 2011 - XP - 2 Machine office
When I use the pdf plot drivers from AutoCAD or the export to pdf option the resulting pdf is not available to the other computer trying to access it through a shared folder.
When I plot to pdf with batch plot or export the drawing to pdf and save the file in the shared folder, the other computer can not open the pdf (file not found) or attach the file to an email (you do not have permission)
Why is this? All other files share and open fine. Only pdf files from batch plot, plot to dwg to pc3, or export to pdf. This is a pain and I still have to use another plot driver (cutepdf) to get a fully useable pdf for our office.
When I open a new drawing in my AutoCAD 2013 that I just recently installed last week, I encounter a problem that I am not familiar with from previus versions of AutoCAD I have worked on. First of all, the units default to decimal, and I want them to default to architectural, with feet and inches. I have to type UNITS in the command line every time I open a new drawing in order to adjust this. I have AutoCAD for Architecture 2012 on another computer, and the program automatically defaults to architectural units upon opening up. Just to let you know, the program I am having this difficulty with is part of a package called Autodesk Building Design Suite 2013. I was under the impression that it included AutoCAd for Architecture, but I think it has only standard AutoCAD.
The scale of the objects I draw vs. the scale of the drawing field is very out of proportion. What I mean is, when I open a new drawing and draw a 30' -0" line, the line appears so long on the screen that I cannot see the whole object, even if I zoom out to the maximum. I should be able to see the object in it's entirety. In fact, when I draw a line that is only 12" long, even when the zoom is all the way out, the line looks huge in length. I have tried adjusting the units to the architectural/inches setting of course, and I have tried adjusting the scale in model space from 1:1 to 1/4'=1'-0", but nothing is working.
I am having some problems getting the hang of applying the drawing scale to my assignment. I understand the scale factor that is applicable to the printing only and that AutoCAD doesn't care about the units used...but something is not clicking here and I'm sure it is pretty simple. My assignment requires me to draw 3 simple structures at 1/8" scale on 11X17 paper. Each house is 20' long with 10' walls and each is done in absolute, relative, and polar. I actually completed the work with all 3 formats without specifying the scale or paper size, just to get familiar with the commands. But now that I am trying to set the dimensions correctly, I cannot replicate my work because I'm getting lost in the way things are defined. I am using AutoCAD 2005, also have a 2002 version to which I can defer.
View 9 Replies View RelatedI am using autoCAD 2011. I have a problem. If I do a drawing in autoCAD in mesarments that they should be in real life. For example if wall is 9000mm long I type in 9000. Building plan like that is easier for me. But problem comes when I try to plot it to scale 1:100 for ISO A3 paper (420x297) How Can I make it fit perfectly and be in-scale?
And another question. If I want to have a frame around my drawing and corner frame with name of the work, who did it etc etc. so I don't have to do it over and over again on every single new drawing. How can I do it? I heared I can use blocks. But how do I fit my block to a certain scale? If I make my block in 420x297 which is A3 standard and do a drawing with 1000- mesarments than it simply will be small for it.
where should i set the scale in the page setup manager or in the layout after i double click on the viewport i get the scale in right corner.
and iam working on the metric units.
I don't know how to plot/scale from layout. I have drawing in model that wont show in layout. Drawing is in scale 1:1 in mm. i have to plot it on 36" paper in scale 1:500. I saw someone scaling it with commands something like, z-s-1xp, an ucs.
View 9 Replies View RelatedI have a drawing I want to plot to 1/8" Scale. I'm drawing at 1:1 scale and When zooming in to draw my line weights look accurate, however when I zoom out to view my whole drawing lines are to thick/blotchy and shapes are distorted. I've played with plot styles, dimension styles and my line weights ... nothing seems to solve this. I believe it has something to do with the size of my drawing.
I attached a drawing.
I have several dxf files that were provided for laser cutting purposes. I have attached one file as an example. I am able to open the file and choose layout 1 and print. If I choose a 1:1 scale the image is very tiny in the corner of the page. If I leave the settings alone and just print, it is a full page, but the part on the paper is not the correct dimensions. The dimensions are in the gif file I also attached.
When I print the dxf file the gap between two of the holes, for example, that should be 70mm is actually like 95 or so. I have acad lt 2004 but also trueview 2011.
Am configuring many page setups and when printing/plotting there is a checkbox to scale lineweights. Was wondering what the consensus is on this. Should the check scale line weights box be checked, or not?
View 5 Replies View RelatedI'm trying to plot a set of drawings that need to be set at 1:1. Every time I pick Custom or 1:1 and set it to 1mm = 1unit, AutoCAD immediately switches it to whatever 1:1_6 is, leaving me with a bunch of empty space around all my viewports.
I'm fairly new at using paper space, and I've never used a plot scale that have underscores in them, so I don't even know what they're representing.
Could we can use 1 ctb file for all drawing scale? The problem is the lineweight at 1:100 is OK but at 1:5 it is quite light.
Could we use scale lineweght?
Is there a way to scale from D size to E size when creating a pdf?
View 4 Replies View RelatedI am trying to plot a map at on 24 x 36 paper and keep it to scale. It appears I have all of the correct settings including 1"=1', fit to paper is unchecked, etc. My print preview comes across correctly but when I go to plot a message appears in the command line stating
Effective plotting area: 26.00 wide by 18.00 high
Effective plotting area: 13.63 wide by 6.22 high
Plotting viewport 2.
Effective plotting area: 13.77 wide by 6.25 high
Plotting viewport 3.
Plotting viewport 1.
The plot then comes out on paper way larger then 24x36 and the area plotted is limited to the 13.77 x 6.25. My co-worker opened the drawing and printed it to scale on 24x36 no problem. What gives? I cannot find a setting to get it to plot correctly.
I'm using autocad 2000 and I have a problem printing & plotting. The print, plot preview only shows a section of the drawing. What settings do I need to change for the entire drawing to print for the paper size I need.
View 3 Replies View RelatedIs it possible to change a drawing using named plot styles (.stb) to colourdependent plot styles (.ctb) within the drawing itself? The variable'pstylemode' comes up as read-only.
View 6 Replies View RelatedI realize it may be a Civil3D question. When I change my drawing scale in the "Drawing Settings" dialog box to 1"=40', for example. The Annotative scale in the Properties Palette changes to 1"=40'_XREF.
View 2 Replies View RelatedWhy in some of my drawings I am not able to select the "scale lineweights" check box in the plotting dialog? I am using 2002. I can't seem to find any differences in these dwgs?
View 2 Replies View RelatedI'm using 2004lt- I have current .dwg in modelspace and set up to plot in PS@ 3/23"-1'-0". I'd like to create a second set of PS tabs to plot portions at 1/4"-1'-0" on the same border when needed.
In its a single viewport in MS and PS the current scale is 1:1 but if i change it to 1/4"-1',etc the plot preview appears wrong
Plot scale / Annotation scale / Viewport scale
I couldn’t figure out how these three types of scales are correlated with one another. For example, my drawing unit in AutoCAD is meter. And thus if I need to print my drawing with a scale of 1:200 then I set the annotation scale to be 1:2viewport scale to be 1:2plot scale 100:1000
if I need to print my drawing with a scale of 1:20 then I set the annotation scale to be 5:1viewport scale to be 5:1plot scale 100:1000
I couldn’t derive the rule that controls these three types of scales. This is also quite confusing when working with C3D! Sounds not the same logic is applied.
I am working on an AutoCad drawing (Vers. 2013) that I got from someone else. I am setting up my drawing and right clicked my sheet tab as usual to go to the page set up manager. I set up my printer, ctb, paper size etc. But when I try to set my plot size to 1:1 it won't retain it and reverts to 1"=1'. It will however let me switch to anything other than to 1;1 (ie 1:10). I checked some existing drawings and the problem doesn't show up. So it's just this particular drawing that's messed up. I checked my drawing units and drawing setup commands and they are the same as I always use.
So the question is why won't let me use a plot size of 1:1?
I have recently started working on a project in metric and have a weird (to me) issue when I try to plot. There are literally hundreds, of scale options in the Scale popup, most of which make no sense to me. I know that I need 1:25, or 1:100 to fit on the page I am printing to. How do I remove or filter out all of the others such as 1:100 3_1_1_1_1_1? I don't even know what that notation means.
View 9 Replies View Related