Is there a way to print out the exact scale just like using manual printing or I just can use
// a 1 inch: 2 units scaleacPlSetVdr.SetStdScale(acPlSet, 0.5);// a 2 inches: 1 unit scaleacPlSetVdr.SetStdScale(acPlSet, 2);
By the way, setting for example (acPlSetVdr.SetStdScale(acPlSet, 2.04);
I get eInvalidInput error.
I have just bought and installed Lightroom 5 and need to set my print size to A3 and in the future even bigger. I do not have the facility at home and need to have them sized correctly for the print shop so they do not have to waste time resizing them. I am at a loss how to do this. I cant find any settings for this size print. A3 is roughly 42 x 29.7 cm.
View 2 Replies View RelatedI am rebuilding the entire back porch.
I would like to set the scale so i can visually see where my joists , hangers , tiers, etc go.
How do i set an accurate scale for a drawing such as this?
Setting Scale .porch.dwg
THIS DRAFT is most certainly NOT TO SCALE.
As usual, i am NOT sure i am asking the right question.
I am trying to use the smallest of the squares in GRID to equal "X" amount of inches so the entire drawing will fit. I do NOT need to use grid if it there is an easier way. No contractor...I am the only one using this and its just to make my initial materials list and get a picture of how things will go....
There are several ways a user can set the scale of a paper space layout viewport.
Properties palette.
ViewportScale_Properties.PNG
Quick Properties.
ViewportScale_Quick.PNG
From the Taskbar. You'll find this in the lower right-hand corner of your screen.
ViewportScale_Taskbar.PNG
Via the Viewport Toolbar.
ViewportScale_Toolbar.PNG
Or manually using the Zoom > Scale > nXP option at the Command line. This method requires the user to enter a scale factor.
For a list of frequently used scale factors, both imperial and metric, refer to this thread. [URL] .......
I can read a view scale with:
BaseViewScale = oDoc.Sheets.Item(1).DrawingViews.Item(1).Scale
But When I try to use the following line to change the scale, I get a compile error.
oDoc.Sheets.Item(1).DrawingViews.Item(1).Scale = BaseViewScale
What type of variable should BaseViewScale be (single, double, string)?Inventor Routed Systems 2010.
Subscription Advantage Pack SP3
Vault Collaboration 2010
Windows 7 x64
Dell Precision M6400 Covet
My viewport scale list only has metric and I would like to add a list of imperial scales for general use. So far I can only add, through Annotation Scaling panel and Scale list for an individual drawing so once it is closed I lose the scales.
how do I list my imperial scales permanently for use throughout the program.
I'm on Autocad 2010.
When setting the viewport scale how do I know if I'm scaling to an A3 plot or A1 etc.
View 9 Replies View RelatedTrying to set the scaling of bitmap images and the scaling is stuck in in(chess). As I am working in metric with everything set to metric why is in still in imperial and can this be changed via a setting?
And what happened to the 'fit to gismo' setting? How are you supposed to do this now?
How to set the view port scale setting in autocad civil 3d i need to print using plan production template.
View 1 Replies View RelatedI'm drawing something much larger than the paper so I would like to chose paper size A(8.5x11) set the scale then print it out on A(8.5x11) paper. For example: my desk is approximately 65inch x 30inch and I want to draw and print it on A(8.5x11) paper. I want it to print with the drawing being accurate to scale...how do I do this?
View 9 Replies View RelatedI am using version B.219.3 (UNICODE) of Autocad Civil3d 2008 with service pack 2 loaded.
I am putting together some plan and profile sheets for a civil roadway job.
The annotation scale setting of the text in the profile xref and alignment xref is being ignored in the sheet file viewports. This text should be appearing at 1:40 scale, automatically, same as the viewport scale, but they are appearing very small instead. According to the way annotation scale is supposed to work in Autocad2008, this annotation should be appearing at the correct scale, automatically.
If I try to adjust the annotation scale to a ratio I think will work, it automatically adjusts the viewport scale to match whatever I enter for an annotation scale. What to try next.
Can files become corrupted in AutoCAD? If so, are there utilities to repair corrupt AutoCAD files?
AutoCAD to draw various drawings, my issue to set scale.
1. what are the procedures of setting scale in modal space? say if is 1:1 then how to make 1:2 or how to recognize if someone has set a scale say 1:20 in modal space so that you return it to 1:1?....( here i need the procedures)
2. what is different among the following, one using mm, another using cm and the third one using m when drawing in modal space, do these people face different if they decide to use the same scale in layout to print? say if they us 1:50xp, what will happen, in their output.
I have imported a ISO Shipping container but the scale is to large. How can I scale it down to architecture setting standard not metric. When I try to use the scale option all it does is makes it larger? I have not search yet do to time restrictions.
View 4 Replies View RelatedSUBJECT: Annotative Scales.
I have a drawing with a 2 viewing ports
Port 1 is at 1/4"= 1'-0"
Port 2 is at 1/2"= 1'-0"
What should my Annotative setting be in model Space?
IN this drawing, I want the 9.00 to be either 4 ( feet) or 48 (inches).
How do I set the correct scale in this or any drawing?
I set up a new page thus (I live in a country which uses metric units, so ...):
Drawing Units Setting18-07-2013 9-24-06 AM.jpg
Then:
Command: '_limits
Reset Model space limits:
Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0.00,0.00
Specify upper right corner <3.5000,2.7000>: 3.65,2.74
Command: C
CIRCLE
Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 1000,1000
Specify radius of circle or [Diameter]: 250
Command:
and I get:
Range Problem 18-07-2013 9-36-57 AM.jpg
The circle was centred at x=1000 metres, y=1000 metres, yet it displays right down at the bottom left of my screen. Compare the radius of the circle to the distance from the centre to the origin - it's nothing like 1:4! Look at the coordinates for the cursor!
Zooming in and zooming out has no effect on the huge dimensions indicated by the coordinates.
I know this must be simple because it is not mentioned in any textbook or tutorial I have been able to find. Authors don't seem to think it is important, but it's driving me nuts! The question is this:
How do I set the page size and grid scale to something sane?
I am pretty sure that this scale problem is at the root of many of the other problems I am having. A14 is doing it's job faithfully but the display is so small that I cannot see what is happening !
I have a problem that I cannot seem to solve. I have a drawings with a whole bunch of layout tabs that have a few viewports in each tab. One of these viewports on each layout tab is on the layer VIEWPORT. I did this so it would be easy to filter out the other viewports in the drawings. I am using the code below to change all of the viewports with the layer VIEWPORT to the Custom Scale 0.020833. This works for all of the layout tabs except the first tab. It will not for some odd reason work on the fist tab.
(setq vieportfilter (list (cons 0 "VIEWPORT")))
(setq ssetvp (ssget "x" vieportfilter))
(setq cntrp 0)
(while (< cntrp (sslength ssetvp))
[code]..........
Setting the scale in a view port in paper space? 2010
View 3 Replies View Relatedcalculation a viewport scale of 1"=30'.
I've looked around and only find nearly what I looking for. For 1"=20' I have a value of 0.004167 Paper Units = 1 Drawing Units, but what is the formula to calculate 1/30"=1'-0"?
This is not a 2012 problem it happened to me with other 3ds max version, well my problem is im working with unit scale in meters, so when it comes with small geometry it disappear when i zoom in which made dealing with small details are hard to model and to see.
View 5 Replies View RelatedI want to create a scaled drawing. I make geologic cross sections with drill holes that are 500 to 1000' deep. I would like to set the drawing scale to something like 1"=250'. So a 1000 foot drill hole would be a line 4 inches long on the screen. I have gone to the Drawing Scale List and figured out how to create a new scale, but nothing I try allows me to change the drawing scale from 1:1. I can edit the list, but I can't change the 1:1 default.
I have tried right clicking, double clicking etc. It seems that the drawing area stays at the original 1:1 scale. What am I doing wrong? I want to make a drawing where I can give the Line command the coordinates 250,0 and it draws a vertical line 1 inch long.
I receive drawings from a company that uses a custom color of 0,0,255 in their drawings and it plots out blue even on monochrome. How can I make a pen setting so this plots out black?
View 5 Replies View RelatedI just got Autocad 2000i as an upgrade from 13 and 14. I have a summagraphics HiPlot 7200.It was set as a windows system printer on the old autocad versions, 2000i will not accept the widows driver (which works great on the old systems) and i have to use hpgl emulation wich sucks on 2000i
View 2 Replies View RelatedI have to set up my drawing on the model page so that I can save it as a PDF and then transfer it into adobe illustrator. My scale is 1:1, and when I put it on the model page I'm doing a 1/8" : 1' scale. It should fit on the page no problem, its only a 9" model plan on 1/4 scale, so it should be 4.5" on the page. However, it's too big for the page.
View 1 Replies View RelatedI'm doing some building drawings for Uni using AutoCAD 2010 and what is the best way (and process) to set line weights and types (dash, dot) for printing. What I’m currently doing doesn’t seem to be working and seems a bit inefficient.
The way I am doing it at the moment is that I have put all the various drawing elements on different layers with varying colours. I am then going through each layer in the layers dialog box and setting the line weight and line type as required.When in paper space or plotted the lines all come out solid/continuous and with same weight. (Note: I have used LTSCALE so that the dashes are viewable in model space). So here are the questions: Does the line weight and line type you set in the layer properties equal what should be printed? At the moment it does not for me. It is best to create all your layers and individually edit each layer for line weight and type, or is there a quicker way to assign line properties? I think I read that you could assign different properties to colours, but not sure what this means.
Just wondering what the best way is to set-up my units and scale preferences in 3dsmax. I would like to have my units in mm or cm so that when I import an object with known and precise measurements, it will stay consistent in 3ds max. So that I can visualize the objects in the correct scale and make measurements with the right numbers.
Of course I dont want to mess with results ofmy textures, animation, camera and anything else in 3ds max and would want to have everything behave normally if my units were in cm or mm in stead of the default.
Win7 Pro 64bit
I7 3680 6 core 12MB cache w Corsair H80 liquid cooling
ASUS P9X79
32 GB DDR3
NVidia Quadro 5000
3TB WD
AutoCAD 2013 crashes during the plot configuration for our printer. When I select Custom Properties for our Kip 5000 Series Printer I get an Unhandled Exception popup. When I click continue I get a message that "AutoCAD Applicaiton has encountered a problem and needs to close", the program crashes. AutoCAD 2013 will not let us select the kip 5000.pc3 file we used for Autocad 2012.
How can I set my printer up if it keeps crashing the program. Is there a new driver for 2013, if so where do I find it. Is it from AutoCad or the printer company Kip America (who have yet to reply to my email).
I have attached the error message
I've been trying to print an A3 pdf from autocad and I've realized the drawing it's not properly dimensioned...
It's a few millimetres less than it should be. How can I sort out this issue?
I am currently printing/plotting a ANSI D size drawing to 1:2 scale but whether I plot directly to the printer or publish to PDF I lose the drawing border.
View 7 Replies View RelatedCould we can use 1 ctb file for all drawing scale? The problem is the lineweight at 1:100 is OK but at 1:5 it is quite light.
Could we use scale lineweght?
Why in some of my drawings I am not able to select the "scale lineweights" check box in the plotting dialog? I am using 2002. I can't seem to find any differences in these dwgs?
View 2 Replies View Related