AutoCAD LT :: Create Template For Cutting Square Hole 125 Mm On A Side?
Jun 29, 2012
Here's something that should be simple, I want to create a template for cutting a square hole 125 mm on a side.
I have gone into Drawing Utilities and set the units to millimeters. I drew a square 125 units on a side.
In paper space, I selected a template that is 11" X 17". I set the scale to 1:1. I thought that that would give me a sheet I could print out ledger size with a 125mm square drawn on it, but no, it is not even close. As near as I can figure, the square is 125" on a side in paper space.
View 5 Replies
ADVERTISEMENT
Jun 18, 2012
put a hole through the side of a 3d cylindrical part?
..___________________
/ ........ __ .................
...| ....../... ..< There....|
...| ......\__/ ................|
/___________________/
I had trouble uploading a screenshot of the part, awful drawing. Essentially the hole through the side of this crudely drawn cylinder is what I need to add. I am using AutoCad 2000.
View 9 Replies
View Related
Oct 29, 2013
I'm making a throttle body spacer in 2013 For some reason I can't get a hole made on the side of the extruded side.I place a general point on a new 2d sketch and no luck.
View 7 Replies
View Related
Mar 8, 2008
Ok so i am making a signature with a video included and i want to cut a rectangle into a box that i made so that the middle is transparant.
whenever i use marquee and select over the area i want to delete and press 'delete' it deletes the whole box.
I am selecting the right layer i know that for sure. Wondering if its something i have enabled maybe.
View 1 Replies
View Related
Apr 6, 2011
I have 2 pieces of round pipe meeting in a V shape, one of them being cut to sit on the other. I need to make a template so the shop guys can put on the pipe for marking the cut, so if i get the section of pipe modelled in 3D, can i then unroll it to procuce the template ?
View 9 Replies
View Related
Oct 15, 2013
The objective is to section a part, selecting a center of the hole (side view, not top view) to attach the section line.
In the hole's top view we can select the center hole to attach the section view, but in the side view, i can´t find any attach point, even if i have a center line.
I know we can edit the section line later and create some construction lines to center the section line with the hole, but i wonder, there's a better process, more automatic, to achieve this?
View 3 Replies
View Related
Jul 5, 2006
I want to cut out a face leaving a hole. Then, I want to drag whats left and drop it over another face. I've tried using the pen tool but I cant seem to discard the face to leave the hole.
View 1 Replies
View Related
Apr 19, 2007
How in the world do I cut a box in half so I can have 2 objects I tried using the slice tool, but not working.
View 4 Replies
View Related
Jan 3, 2005
I want to crop a square section from an image, using the rectangle tool, under options i choose square but then it blacks out the section of the image and is not movable, in PSP7 when doing a similar action, this square part of image is movable, how can i make this the same in photoshop?
Or is there a different action that i can use?
View 4 Replies
View Related
Dec 1, 2010
Is is possible in InDesign to have a stroke on only one side of a square? And if so, how do i go about doing that?
On Mac OSX 10.6.4, InDesign CS5
View 17 Replies
View Related
Sep 17, 2013
I have two picture files and I just want to create one file, displaying both pictures side by side. I have been reveiwing all of the functions in my Adobe Photoshop Elements Version 11 and I can't figure out how to do it.
View 2 Replies
View Related
Jan 13, 2014
I want to create a banner heading from two pics side by side, but mixing together at the centre with about a 15% overlap into each other.
View 1 Replies
View Related
Oct 25, 2012
I am cutting a dormer in a roof with a square rafter cut. I want the dormer to be plumb cut. Is there any way to do this? The property seems to be set for the entire roof.
View 3 Replies
View Related
Oct 9, 2012
I am starting a football pool and I can't find a PSD template. where I can find one?
View 4 Replies
View Related
Jul 25, 2012
I am making a video in Nero Vision 10 and need to cut out the screen of a tv so that I can layer the TV over an image/video so it looks as though it is on the screen. I enclose a screenshot of the project. 'Transform-tools-crop' only cuts in straight lines so I wonder which device I should use which can cut out an odd bespoke shape? You can see in the uploaded image from the project how the image currently cannot fill the frame without covering it.
View 7 Replies
View Related
Dec 27, 2003
I have these two pipes, one is 4" diameter (running horizontally) and the other is 6" diameter running at a 30degree from horizontal angle. eventually the two hit, and at that intersection I need to make the 4" pipe join to the 6"' pipe, which then continues on its merry way farther down the structure. So I can extrude the two pipes, and I can even make a union and then remove the excess of the 6" pipe, because what I am really looking for is: a cutting diagram for the joint where the remaining 4" pipe hits the 6" section. A cutting diagram for the short piece of a Y joint.
I can make this image appear on my screen, but I am then stumped as to how to unwrap the pipe into a flat section so that I can see the curvature of the cuts required in planar view, for the real pipe that I have on my shop floor.
View 9 Replies
View Related
Apr 2, 2012
I am basically new to inventor and I would like to get any tips from this forum on how to go about creating a pocket hole like the Kreg Jig. I am a woodworker so this would come in very handy when I am building furniture sketches.
View 9 Replies
View Related
Aug 6, 2012
I have one part like below attachment image.in this part using patten in part level in single pattern only how to maintain different types of pitches.
View 1 Replies
View Related
Nov 9, 2012
is it possible to create a hole note without pitch.
i use standard thread in most cases so i just want the thread to be shown in the holenote tool on drawings (like M8 not M8x1,25)
View 1 Replies
View Related
Mar 8, 2013
I need to create a hole table for a part. I would like the origin to be at the center of the part. Problem is there is not a round hole at that location. Attached is a similar part. The one that I am doing is much larger and has many more holes... this is just an example.
How can I pick this as the origin of my hole table?
View 3 Replies
View Related
Jan 29, 2013
I created a cylinder with a hole through the center and need to add holes through the face into the center hole and I can't figure out how.
View 9 Replies
View Related
May 26, 2013
Im new in Inventor and I have a problem with creating a hole through two parts beacause they are a bit angled. Im creating the holes part by part and Im using the work point method. But unfortunately this is the result:
Im wondering if there is any other methods so I can get the holes coinciding?
View 1 Replies
View Related
Dec 20, 2012
what ive been trying to do is make a helix that sweeps around a rectangular prism i was able to make it in solid works but i cant find a way to do it in inventor.
View 9 Replies
View Related
Jul 3, 2012
I'm trying to create a hole in a sheet-metal part so that a pipe can be welded in it, see attached picture. What's the best method to do this? Because the flat-pattern of this hole isn't an ellipse-shape (more like an egg), it seems it's very difficult to do.
Product Design Suite 2014
Inventor 2012 SP2, Vault 2014
HP Workstation Z220
Intel Xeon 3.4GHz
16GB RAM
Nvidia Quadro 4000
Windows 7 Professional (64bit)
View 9 Replies
View Related
Jul 10, 2013
How to create hole or drill chart table in AutoCAD LT 2014
View 3 Replies
View Related
Sep 28, 2012
Press/pull has been working fine up until now. When I try to press/pull a boundary, it creates an invisible extrusion rather than cutting into the object.
View 3 Replies
View Related
Feb 5, 2013
I am currentrly trying to pattern a series of square holes that form a simple aztec pattern (attached). I am planning to fill the holes with black dye/paint in order to represent the aztec pattern (hence the holes need to only be about 5mm deep.
The pattern itself should be about 2cm*2cm.Is there a way to use an image such as the one attached and make it automatically translate that into holes, or do I have to draw it all manually? If I do have to do it manually, c how to create square holes?
View 2 Replies
View Related
Sep 3, 2013
In order to reflect production process, I have to create holes on the bent pipe at assembly level after 2 bent pipes are welded to the straight pipe. Now when I suppress holes, it does not suppress only at LOD or view rep but throught the whole assembly.
Is it possible to suppress features such as hole using LOD or view rep, which are made at the assembly level? or I have to use another method? See below in highlighted.
View 1 Replies
View Related
Dec 15, 2011
I want to create a pyramid with a base of three sides with different lenght. In the end i want to have a solid where i can drag and move the notes to change the hight,lenght and the angle of the sides.
I already managed to draw it in 3d but now i want to convert the drawing into a solid and keep it flexible to change the parameters by draging the notes.
I also tried to extrude a triangle with a specific angle but then i was only able to move the top note up and down changes the hight. Doing it this way the top note also kept beeping in the center-point of the triangle.
View 7 Replies
View Related
Nov 6, 2012
I've got a template with a set of Object defaults for an Inch drawing and a set for a Metric drawing. I've just noticed that within my metric set, if I insert a hole table with tapped holes, the font on the tapped holes doesn't match the other hole types. I'm searched around, but all the settings for the hole table style reference the same text style. (Please see the attached image.)
So is there a way to set a certain hole type to have a certain font or size within a hole table? Because if there is, I'd obviously like to remove it..... But I can't seem to figure out where the issue is.
View 5 Replies
View Related
May 22, 2012
I am trying to add a hole to an existing hole chart. I drop the part into a new drawing, set the ordinate "zero", and add a hole chart by selecting a few holes. When I attempt to edit the chart: click chart, right click "edit", click add hole, select new holes, right click to create, the "create" selection is greyed out and all I have to choose from is cancel. I searched the forum here but could not find a reference to this a know issue. Am I doing something wrong or is this a glitch of 2013.
We are running win7 x64 machines and this happens on both the 2013 Ultimate and Premium editions of the product.
View 9 Replies
View Related
