Is there a way to force Inventor to dimension without snapping to various Z heights within a drawing view? I have basic top and side views created however when trying to dimension overall lengths and widths i'm snapping to high and/or low points of the model and getting screwed dimensions.
View 4 Replies
I have a VB program that auto updates the size of a door and frame assembly, and in turn, updates the shop drawings to reflect this change. I have a view on my shop drawing that I have drawn a sketch in. I start the sketch, add my dimensions, and I use 'Project Geometry' to project the edges of the actual part around the sketch to constrain my sketch and keep it in place. The problem is, as the program runs, and the door/frame changes height, the sketch loses it's dimensional references to the projected geometry. When I go back and reopen the drawing after running the program, all the dimensions that went to the projected geometry are gone.
Is there another way to anchor a sketch to a drawing view part instead of dimensioning to projected geometries? This doesn't seem to be working, and I've tried it every which way I can think of. Oddly enough, I have another sketch in a different view that is set up the same way, and it never misses a beat.
unable to select an edge in the drawing view to create a general dimension.
View 1 Replies View RelatedAny way using autoCAD LT 2014 to get CAD to display the elevation heights of survey points without having to type the heights in text bozes next to each individual point. i can insert a field which displays the elevation of the point but doing this again i would have to do every point individually.
Another words is there a way to select all the survey points required and get CAD to display a certain property, which in my case is the elevation height of that survey point, next to it? so it looks like x 23.35 x 23.57 etc..
I have a detail view of a groove on a cylinder. I want to dimension a diameter in which I only see one side, the other side is not in the detail view.
From some posts I see that I should auto insert a centerline then dimension from centerline then choose options "dimension linear".
First when I try to auto insert centerlines it does not insert the centerline for me. Perhaps because my detail is smaller. If I make the field for the detail view larger it makes a centerline, but I dont want to do that. I have tried making a sketch of the other side and the centerline. When I dimension from here I do not have the right click option of dimension linear, instead only arrowhead options.
Using Inventor Professional 2012
Is it possible to have the parent view for the section in one drawing and the child views in another drawing?
View 2 Replies View RelatedAfter upgrading to Inventor 2014 we notice that the graphics do not work properly, and that the overall performance in drawings and modelling bad compared to 2013. Then we installed SP1 and now drawing views are disappearing, however when we select "shaded" view the view reappears and works perfectly..
Any workaround regarding disappearing views?
Each time when I place a part in base view, have to follow few steps; go through view label, format Text, than choose type option - [Properties-Model] and its property - [Part Number], than placing dimensions. it takes long time and very repetitive, especially, when placing a hundreds of parts and I was wondering if there is an option, to set up view label; [Properties - Model ]& [Part number], as a DEFAULT. So, each time placing a part, in base view it will come up with correct label. Also, overall dimensions, can it be retrieve using parameters of the part?
View 4 Replies View RelatedI have a flat pattern with ordinate set dimension, taken detail from one end.
parent view having ordinate dimension from left end and i have taken detail view of right end.
i need detail view dimension with same origin dimension as like parent view.
I'm currently learning Inventor and going through the tutorials. At present I am learning about drawings. For some reason the scale (e.g 1:1) and dimension numbers do not appear in the drawings. I can see the arrows that make the dimensions but that is all. How to turn these on? I have tried every setting I can find but it appears that I can't figure this out.
View 1 Replies View RelatedTrying to dimension a shaft in isometric view with various diameters. I am unable to find or select the centerpoints at the ends of the shaft. This causes dimensions to be crooked. How can i get the centerpoints to display so that they may be selected?
View 9 Replies View RelatedTurn off snap to objects.Now select a dimension tool and draw either a vertical or horizontal dimension line.Now notice the snapping to objects is re-enabled.How can I stop this from happening without having to keep turning of snapping while in dimensioning mode?This looks like a glitch in X4 because I don't see this problem in X5.
View 4 Replies View RelatedThe diametric dimension on the right, dia. 244.9 isn't resembling the real dimension in the weldment.You see in the sketch of extrusion 2 that i gave an internal diameter of 245.
View 9 Replies View RelatedIs there any way to highlight certain dimensions in a IDW drawing (i.e. color the background of that text yellow)?
View 6 Replies View RelatedI am using Inventor 2013. For some reason I cannot dimension some of the model entities in the drawing views in an idw file. I can retrieve the model dimensions but it is usually easier to create the dimensions I need in each view. I can select the line, curve, etc. when dimensioning but nothing happens.
After I think about it. What I cannot dimension are lofts that I created with rails. These rails were made up of lines and curves, not polylines. How do I get the sketches for the rails I used for lofting to display in the drawing views so I can dimension those sketches.
I'm using Inventor 2013. I created an assembly where I did a lot of top down modeling (meaning components in the assembly were created in the assembly. All but a handful of the components are adaptive to other components). When I went to make my drawings for having the components made, I started noticing that some of the dimension values were wrong. I could go into the model and verify the features, but when dimensioning on the drawing it would not match. Furthermore, this didn't occur on every dimmension on the drawing. Not even half of them were incorrect, but it only takes one to really mess up a part.
I've attached a screen shot of what I'm seeing. The 15.2 and 5 dimmension are correct, but obviously those don't add up to 31.37. I know I can manually override this dimmension, but only if I know to do it. I tried to do a drawing of another part in the same assembly and eventually found a similar problem.
Finally, I created a step file of the 1st part (to strip away the adaptivity) and when I created the drawing again, the problem went away.
My question is, is there something I did in the assembly / creation process that would have caused this?
I'm trying to dimension an ellipse in the Inventor Drawing Feature. I've attached the .idw files. (the .ipt is too large)I am aware that the ellipse doesn't have a constant radius and was wondering what is accepted practice for these dimensions?
I need to first dimension the external elliptical shape (which I'm struggling at), might just add a note.
Secondly I'm trying to dimension the mesh part, its not centrally align to the part and since I can't put a center mark on I'm not sure how I should dimension this...
My question is to find the dimension in the drawing area
for example
If we observe in the drawing left hand site we can see alphabets in the border area and number at top border area
if the dimension lies between "A" on left hand side and "1" on top border srea
then i want a message the dimension lies on A1
dimension bend parts with corner intersection. Is there any option in Autodesk Invenor Drawing so that i can give dimensions as shown in attached image.
View 2 Replies View RelatedSo my problem is that I need to include a line on a part drawing that isn't related to the part itself. I need to be able to override the dimension of the line I sketched so that I can include it in my drawing and update the dimension without having to change anything else on the part.
Basically, I want an iLogic rule to overide a dimension, and I don't know how to do that.
I have recently drawn a steel construction, and I am now in the process of making the drawings. A problem that occurs is the length of beams used for bracing. When I click the two outer points, the lower dimension in the drawing appears. This is the length of the line between the two points. To be able to dimension properly, I have made a sketch with a straight line, which is perpendicular to one side of the beam. This has been used, with the point on the opposite side, to find the true beam length (and is showed as the upper of the two dimensions in the picture).
View 5 Replies View RelatedI want to ask how to make the size for the angle in the distance between holes. i use the autodesk inventor 2013, I attach an example like this.
View 9 Replies View RelatedI was trying to reposition a retrieved dimension in drawing. I was able to position the text, however the dimension line however still stays in its default retrieved position. how I can reposition the dimension line as well?
Dim mydim As Inventor.ObjectCollection
Dim invDimConstraints As DimensionConstraints
Dim invDimConstraint As DimensionConstraint
invDimConstraints = invPartDef.Sketches.Item("MySketch").DimensionConstraints
[Code] ........
I am using education version of Autocad 2012 and have only around 2 gig of RAM. Whilst drawing , mainly in 3d my osnaps do not seem to work properly. In a lot of cases it is only the "nearest" snap that works. Sometimes I get no snaps when I think there should be plus I get a bunch of tiny green crosses around where I want to snap. Could my lack of RAM be causing this ?
View 4 Replies View RelatedHow do you change the dimension text size in an .idw 2D drawing? The dimension text and arrowhead size is too small and I would like to make it sligthly larger.
View 3 Replies View RelatedWe have created one Style, but within this Style are two Dimension types (Dual and SIngle)
When a drawing from a model is created it defaults to the Dual Option and we can only select the Single Dimensions by individually selecting the Dimension and editing to Single Dimension, which can be time consuming.
Is there a way to select the Dimension type for the whole drawing?
I seem to recall being able to do this in 2013...
Say you've dimensioned something but end up wanting to change the dimension definition points...drag the end point to another location that you want dimensioned.
I thought it used to snap to a new location, but now it will not. I have to redraw the dimension (including all text I added).
Here is what I get when I try to move the dimension definition point:
Here is what I get when I try the auto-reattach feature in "repair". Still nothing to snap to.
I cannot edit a dimension that I add to a drawing, IV simply ignores my request when I select Edit from the shortcut menu. This is not a retrieved dimension. My only workaround has been to edit the dimension properties in the part file to display as I would like on the drawings.
I've checked the application options, under Drawing tab, I do have "Edit dimension when created" checked, yet IV does not display the edit dialogue box upon initial creation of the dimension.
I want to change some values in the default drawing template.
But doesnt succed to save it to an existing template
Like this picture shows about the precision
I have tried to use "Save Copy As Template" but the values goes back to the default settings
how to save dimension style settings to an template?
How do i increase the dimension text height in my drawing.When i go thro the styles and standards editor and increase the text height all the text in my sheet border also increases.Surely there must be a way to isolate the dimension text from the sheet text.
View 2 Replies View RelatedHow can I load multiple dimension styles into an Inventor drawing file without loading them into a template file?
View 1 Replies View Related
