I am trying to place a tubes cylindrical surface to another tubes cylindrical surface using add constraint. How do I specify which side of the target surface to apply the constraint ?
View 4 Replies
Is it possible to apply a tangent constraint to an edge of a cylinder at an angle to the revolved side of another cylinder? I wan't to avoid applying a specific angle constraint if at all possible.
View 3 Replies View RelatedWhy can't Inventor constrain an ellipsoidal contour with a line? We have pressure cylinders which uses a 2:1 ellipse. These cylinder get welded to a base stand fixture. The surface of the ellipse nestles in between contact points of the base stand, in this case lines of geometry. Yet Inventor can't constrain them as such. Any good workflow (at the assembly level) so that we don't have to ground components and use the Analyze Interference tool to make sure we are right on the surfaces? I don't understand why it will work for a cylindrical surface but not an elliptical surface.
View 7 Replies View RelatedI am trying to create a dimension in an .idw that goes from a line to the tangent of the outer diameter. I have tried several approaches but I cannot get it to work. Essentially I am trying to replicate a drawing which was created in Solidworks but I am having trouble with this dimension.
View 4 Replies View Relatedafter the first constraint I can't drag the part,
only thing i can do is use the rotate command
I am designing a vertical axis wind turbine just for some practice (just started using Inventor) and everything was going smoothly until I tried to "animate" it spinning. First, I set up a work plane that goes through the center of the structure, and then I clicked angle constraint "explicit reference vector." After watching several youtube videos, I figured that I should click on the work plane, click on another reference point, and then click another point that would be orthogonal to those two (right?). Well after I choose the first point, Inventor will only allow me to choose the center axis as the second option (which I think should be the third option).
View 6 Replies View RelatedThis is probably a simple one, but when I dimension from an edge to the tangent of a radius or circle. It always snaps to the center. How do I get the dimension to snap to the tangent point?
View 9 Replies View RelatedI am still making some adjustments to our standard drawing template and I ran into another issue..
I want the tangent edges to be displayed automatically when I insert a drawing view rather than clicking the Display Options tab and checking the Tangent Edges box every time I make a new drawing. Is this possible? If so, how?
I tried inserting a view, checking the Tangent Edges box, then deleting my view and re-saving the template but it still went back to the default.
I have a roller pin which follows a certain path using transitional constrain in an assembly. A box is attached to the roller pin which move along with it. My problem is that I want one face of the box to be tangent to the path which the roller pin is following so that the box moves according when it is on the curve. I have attached the file with the message.
View 2 Replies View RelatedSince switching over to Inventor 2012 I have been having trouble snapping to tangent points on a curve or circle to pull dimensions. I would do it manually but if the dimension is not referencing a specific point in the model it turns pink to identify an error.
Is there a setting that may be not allowing me to snap to tangent points?
I am having trouble with a part that I am working on. Trying to trim to the tangent edge. I cant post the part that I am actually using, but here is an example of a similar problem. In the attached file, open the "Negative Part.ipt". The sketch 2 contains a line (unconstrained). I need this line to be tangent with the curve below it.
I can project the edge of the curve to my sketch plane, but not the tangent of the radius.
Windows 7 x64 -12 GB Ram
Intel i7-930 @ 3.60ghz
nVidia GTS 250 -1GB (Driver 301.42)
INV Pro R2013, SP1.1 (update1)
Vault Basic 2013, SP1
Looking at a side profile of a channel in a drawing, you will usually see a top and bottom edge, as well as some nominal flange thickness.
In Inventor, all you see is the top and bottom edge...because the channel's shape is really radiused on the flange.
So I turn on "Tangent Edges" in the Display Options of my view...now I see three lines representing the flange. I can manually hide the other lines, but this option creates a TON of lines in my views that I would have to manually hide.
What is the quickest and cleanest way to represent a channel without seeing a ton of extra tangent lines?
In my drawing, of either a part or an assembly, how do I display tangent lines?
Windows 7 SP 1
64 Bit.
Inventor 2013
ACAD Mechanical 2013
Is it possible to have a tangent constrain on multiple curves?
see enclosed rough sketch, i would like the curved free end or the arm to be in constant contaced with the wavey top line on the other part, the wavey line is constructed as 3 curves but i can only get the tangent constrain to apply to one of the curves.
i would like the tangent constraignt to move between the curves so the part stays in constant contact with the wavey line. this is just a mess about sketch i suppose a real world instance will be a wheel following a shaped cam plate.
How can I create a workplane with the API that is tangent to a surface and passes thru a workpoint. It is easy to create a work plane of type kPointAndTangentWorkPlaneDefObject by point and click in Inventor 11, but I can't figure out how to do it in the API.
View 5 Replies View RelatedI have 2 different diameter cylinders and I would like to create a plane that is tangent to both.
View 7 Replies View RelatedI'm designing a part, and am having trouble creating a plane tangent to a curved surface. One option for creating a plane says "Tangent to Surface through Point", which in theory I should be able to use, but I can't figure out how to actually place a point there before in order to create a surface at the point.
Basically I am trying to cut a circle into the curved right side of the part
I've attached the part file for reference.
Is there any way to have Tangent Edges to show within all view's created on my idw automatically within the my template file or do I have to remember to double click on each of my created views per page, select display options and make sure Tangent Edges are checked on.
*See Computer Mouse is Attached Photo
IV 2012 Pro-Suite / VP 2011
Windows Vista Enterprise - 64 Bit
Precision Workstation T7500
Intel (R) Xeon (R) CPU - E5504 @ 2.00 GHz (8 CPUs)
12284 Mb Ram
Dual Quadro FX 5800
I used Solid Edge for my entire professional career. One thing that is driving me batty is how, when necessary in a view for clarity, tangent lines are displayed and how to change them, or at the very least, come up with a work around to display them how is needed. In general, tangent lines are first, supposed to be of thinner lineweight, but also, are not supposed to extend all the way across the surface of a part, they are to leave a small gap.
I have found and tried the option of displaying tangent lines, and also have checked the for shorten option. The issue is, in many of the parts the gap produced in HUGE. So I've spent a few hours tinkering, and I finally decided to try and define a new linetype using autocad express tools. So I tried this, but to my dismay I haven't been able to set up a linetype that only has a gap at the end. See attached jpeg for illustration.
Does the action (look in .ipt file) shown in the attachment is appropriate and complies with the autodesk wikihelp?
Windows7 64b; GIGABYTE EX58-UD5; Intel Core i7 920 (2.66GHz)
DDR3 3x2GB Kingston, HD ST 750GB+320GB
NVIDIA Quadro FX1800 (1680x1050) + SpacePilot PRO
APDSUltimate 2014
In other softwares when you creat a spline you are able to adjust the curvature between points by dragging the slope handles at a node. In my file, I have thus far been unable to fair my splines with any kind of consistancy. Also, it should be possible to place a tangent constaint to a straight line at a point, yet I haven't been able to do that either. According to the help files this should be an easy thing to adjust, Why am I not able to?
View 9 Replies View RelatedI have created a bin/vat/tub using sheet metal. I started with a contour flange. I then copied the sketch and pasted into a new sketch off the flange for a contour roll feature. Then a flange, roll, flange, roll, flange and roll. My trouble starts at the last flange. I'm trying to construct the flange exactly as I have created the features before. I set the distance, select the profile (it shows the flange on the screen), hit apply and that's when my message shows up. "Non-tangent curves found in path: flat pattern cannot be correctly created. Edit sketch and add constraints to the curves. The sketch is fully constrained according to the lower right hand corner and the auto constrain button.
View 2 Replies View RelatedHow to correct length line Tangent Edges, Foreshortened (sheet metal drawing) ? I didn't find option to correct length line Foreshortened (sheet metal drawing) .
View 1 Replies View Relatedi have problem with the Application option settings for sketch enviroment: When i draw a line in the sketch, i am not able to do the "click hold for a tangent arc to the representing line" it just starts a new straight line.
I know it has something to do with the settings, but can figure out what the correct settings are...
I want to be able to turn off the "show tangent edges" option in a drawing I'm creating. The problem is that it looks fine for some items and bad for others. Is this an all or nothing command?
View 2 Replies View RelatedIs there a way to use the curve driven (rectangular) pattern referencing two tangent curves (an arc and a tangent line). I'd like to be able to create this pattern of slots in one pattern, otherwise I'll have to make two cut features at each end and use one pattern for the straight and another for the curve.
View 6 Replies View RelatedHow to turn on by default the tangent lines and thread features (and any other options) on all new base views in a template idw?
View 2 Replies View RelatedI have an assembly which has components mated to a radial surface, I need to locate the center of a round slot against an axis, I have X Y coordinates, how can I constrain that part to those X Y coordinates?
Attached is a picture of the assembly.
I am currently creating a chain block to be animated later on. But, I do not know how to constraint it.
I have attached a zip file of the .ipt and .iam
Maybe I've just been doing it wrong for the last 5 years, but the Angle constraint is obnoxiously unpredictable. When I constrain a part in an assembly with an angle constraint from the assembly origin plane (or anything else), Inventor always has two solutions; a positive and negative.
Is there something I'm missing here, or is just a design flaw we have to live with?
I have a question regarding a transitional constraint between a pin and a surface within an adaptive assembly.
I would like the pin and the surface to be transitional only when the two parts "interfere" with each other.
At the moment with the example attached part A is remaining tangent to part B, restricting the necessary movement of part B to function properly in the mechanism.
In simplified terms I need part B to be able to break free of the "transitional constraint" of part A under certain movement conditions within the mechanism.
