I have a .iam and .idw that i copied/designed from vault. The .idw has a sketched symbol that has a text box with the mass property. When update mass is applied the mass property in the text box does not. I ran into this once before and got it to work by re-inserting the symbol into the .idw but I can't get it to work. The orginal that was copied from works fine.
IV2013
Vault Collaboration 2013
I have recently made a bucket for chain (linked) and was looking to put the chain in the bucket for visual purposes and to see if the capacity of the bucket is correct.
I can get the chain linked together, however when rotated round it passes through another piece of chain.
Is there a way in inventor to tell a part/assembly of it’s physical/mass properties? I know you can make something mild steel and get weight etc, however if not constrained it still passes through as if it’s a ghost.
I am having a problem with an assembly not showing the correct total mass of all of its components and sub-assemblies. The value is out by nearly 20%, over 3000kg!
I have narrowed the mass discrepancy down to a derived part of a sub-assembly. But this incorrect mass is only present when I navigate to the derived part's iproperites via the browser tree of the higher level assembly where I am having the mass problem. It is as though the top assembly got some of its mass property information from a previous point in time, i.e. possibly before the derived part's mass properties were updated, and now refuses to look at the current information.
By the way, I have opened up and checked the mass properties of each sub-assembly and the derived part; and when opened individually these show as correct. I have also tried 'Rebuild All' with no success.
Is it possible for mass properties in an assembly to become corrupted?
I've has Inventor tell me this for thin walled tubes with holes in them, but not for a simple part like the attached one. Autodesk are you listening yet? This has been an issue for a long time. Mass calculations for parts with holes on curves do not work properly. On many parts the error comes up with "low" selected. By default each time I try to save the file, the error window pops up.
View 8 Replies View RelatedI have an assembly that I am trying to get the weights every time I update parameters.
View 3 Replies View RelatedHow would i insert the "variable name" of a custom iProp to a sketched symbol definition (in an idw)?
I can plonk the value of the iProp in no worries, but to make it "live" is a bit beyond me...
Sub WeldNote()On Error Resume NextDim oDoc As DrawingDocumentDim SketchedSym As SketchedSymbolDefinitionDim oNoteDef As SketchedSymbolDefinitionDim oDefSketch As SketchDim oTextbox As TextBoxDim SNewText As StringDim sNoteText As StringDim oReffedDoc As DocumentDim lReffedWeldType As Long'Err.ClearIf
[Code].....
As this software continues to change it's behavior of function over nite. I am assuming due to new updates in inventor. I can no longer get my drawing to update per changes made to the model. This started about 2 weeks ago.
Change are completed perfectly, I open the drawing and it still has the old model represented. When I right on the view and open the model. Model contains all of my changes, but the drawing does not seem to care or notice that changes have been made and saved. I even closed inventor and reopened.
Even though I'm paid by the hour I really do not want to delete all views and start all over.
So the only answer is to delete all views replace them re dimension them and of course add any time consuming sketches.
10-15 minutes change now is going to take 3 hours. WHY can't autodesk make a stable piece of software?
I am having trouble with dimensions disappearing in the drawing when I update my model.
I add the correct dimensions then when I update my model, all dimensions on the drawing disappear and I have to make them all again.
A little more info:
I am using the tube and pipe feature to drawing tubing inside of an assembly.
Process:
1) I draw the tubing routes and populate them (to show an actual swept tube)
2)Right click on the newly created route in the explorer and open the tube.
3)File->new->drw.
4)Add necessary dimensions to the tube drawing.
5)Save and close drawing
Up until this point everything is fine.
6)Edit the tube route in the assembly and save
7)Upon opening the drawing of that tube route ALL dimensions have disappeared.
I'm using Inventor 2011 and when I go to change parameters using iLogic in an assembly model, (sometimes it is a component suppression, other times it is an iPart component change) it won't update the associated drawing file. I need to go into the BOM on the drawing and renumber the balloons, or change something else in order for the custom iProperties to update in the drawing template. If I just change the iPart component, then the BOM doesn't need to update making the renumbering of balloons redundant.
I'm using iLogic to update all of the iProperties and component references, then reattach balloons. What I would like to do is automatically update the custom iProperties drawing template fields, and renumber the drawing BOM.
I am developing an simulation application, leveraging on using Space objects and applied additional Property Set Definitions for Space objects where I introduced a new Property "Value".
I applied a display theme to my DWG, and based on the value of the Property, different colors will be displayed according to the display theme.
For a single DWG file containing the building, I am able to simulate the color changes by updating the “Value” Property in the Spaces using .NET APIs functions such as PropertySet.SetAt, and committing the transaction.
However, one building can consist of many different levels, and I have split up the modeling of the building into its separate levels. For example, a 3 storey building, I will have 3 DWG files for each individual levels.
A main empty DWG was then used to XREF the 3 levels, to combine the different levels into a whole building. I would like to simulate such colour change through the main DWG which references my individual level DWGs.
what .NET API I can use to access the XREF DWGs in my main DWG, so that I can update the "Value" property in all my Space objects?
I've been looking for a solution to remove the unit string ie Lbs, g, kg from the value given from a 'Mass' value in a text string.
As you may all know, creating text and having a 'physical property - mass' value...the unit string is there...
Lots of people on here have the problem...no-one has got a solution.
Until now...
Basically...open the part you need to get the mass property of in your text string.
Follow the instructions on this webpage...this is the first part...
[URL]
Basically, this creates a Mass property value in the parameters table that you can call on as a text parameter.
It's similar to the custom iproperty model - mass but NOT the same.
Once you have done this, you can go to the drawing of the part and create a text string in the drawing and call it up as shown in this procedure. BUT it still has the unit string.
Here's the best bit that you want to know...
To get RID of the unit string...open up the part again from the drawing...click on the parameter icon...find the user parameter...in the Nominal value column, right click on the value and you get a pop-up that gives you 3 options...
Custom Property Format, Make Multi Value & Delete Parameter.
Click on Custom Property Format.
The pop-up window comes up...showing you the property type...in my case...the 4 left columns read Text, g (grams), Format & Precision...
On the right hand side I have a Preview of the text...then 3 check boxes...Units string, Leading Zero's, Trailing Zero's.
Units string is checked.
Uncheck it.
Close it...Save your part...go back to the drawing and hey presto!...the text now shows the weight you require as a straight value...no units!
I clicked on Auto Hide in property palette settings, and now can't bring it back. I click on ribbon where is the property icon or type in command line, the property palette doesn't show up.Reinstalling program didn't work either.
View 2 Replies View RelatedI have problem when i try to use function analyze mass model in revit building they show message like attached file.
View 1 Replies View RelatedCurrently I am using I-logic and a form. I have an assembly that I am pushing a volume from a part to the main assembly. The volume updates in the part fine. The issue is with the form is not updating when the file parameter updates. If I exit the form and run the rule manually then the form updates. how to update the form at the same time?
View 1 Replies View RelatedTwo questions.
Is there a way to add new materials to physical properties?
Is there a cloud feature in Inventor for drawings, or is that something that can only be done in Autocad Mechanical and Mechanical Desktop?
I'm now working on my diploma work and I need to model a gridshell construction in Conceptual mass.I created the form and made adaptive component -a glass panel.I uploaded it in the family and now I need to load that family into the project space and I don't know what to do..I will have to remove the mass eventually before rendering but then the gridshell structure will disappear.I don't know how to make it real,I cannot use massing and site with this, I'm obviously missing some steps and i don't know which ones..
View 1 Replies View Relatedhow I can update the physical properties for a part or assembly, from a drawing? My drawing template is showing the total weight for the current part/assembly, and I would love if Inventor could update this using iLogic, so I don't get the "N/A" value all the time.
View 5 Replies View RelatedI have some issues with the notation for physical properties in the Inventor 2013 material editor.
Instead of displaying the obvious first choice metric SI notation kg/m^3 or something similar it display a self made? and awkward N*s^2/mm^4. I don't want this notation. How can I change to something more user friendly? It can be a bit hard to distinguish if a material have 0.00000000001 N*s^2/mm^4 or 0.0000000001 N*s^2/mm^4.
The document properties "units" folder have mm, seconds, degree and kilogram as default.
I'm trying to add some material properties to a STP or IGES file I've received from a customer (in Inventor 2011). Is there any way to add a density for example, so I can obtain the mass of the model? I've tried doing it through the iProperties menu but it's not giving me a mass.
View 3 Replies View RelatedWe recently moved from Inventor 2010 to 2013. Since then we have been having alot of lag problems. One major problem we have found that is giving us lag is our RAM usage. Inventor continually steals more and more ram until its starts to lag out. When I open a large assembly inventor goes from useing 1.2 GB to 4 GB of ram. When I close the assembly the RAM usage stays at 4 GB. If I open another assembly it just builds onto that and can go up to 6 GB before it starts lagging badly. Closing inventor dumps the physical memory.
System:
windows enterprise (no service pack) 7-64 bit
intel(r) Xeon(r) CPU (2 processors)
9 GB RAM
Nvidia Quadro FX 4800 graphics card
When I duplicate the Material in the Material Browser all appearance and Physical properties are duplicated too.
So I must accept or assign the new unique names for appearance and Physical purposes of Material.
In my case I need, for example, the same Material with different appearance, for example knurled and regular.
I cannot save the new Material with existing Physical properties name and it makes unwanted copies like Steel(1), Steel(2) in Assets.
After I made a copy I can reassign the Physical properties back to existing but it takes a time of replacing assets and deleting unwanted copies.
Is it possible to make a copy within the same Physical Assets?
How do I set a constraint where 2 parts are attached to each other but do not phase through. For example if I have a door in a door frame, how do I add a constraint where the door can swing on it's hinges but get stopped by the door frame.
View 1 Replies View RelatedI am having an issue with my template that I created from an old drawing: the quick view layout thumbnail still shows the old drawing in model space. All of the paper space thumbnails update themselves as I work, however model space does not. It shows the old drawing both when I hover over the model space tab, and also when I pull up all of my quick view layouts. I am using AutoCAD 2009
View 4 Replies View RelatedWhy when I choose a new layer (which happens to have a different colour association) the colour of the new drawn line stays the same?
[URL] .....
I understand there is some setting you type in the command line to solve this problem but I am unable to find what that is.
In "Categories" of the filters window, it can be selected things which composes its mass, such as Mass Exterior Wall, Mass Glazing, Mass Roof. And these things can be clicked only after its mass become energy model.
I set up a filter rule of Mass Roof and applied it to V/G Filters of a view, but it did not displayed in Analyze Mass Model, the same as Mass Exterior Wall, Mass Glazing.
Inventor seems to do lots to allow for simulated appearance textures. However, how does one use actual physical textures, e.g. for a plastic part? I need one surface of the plastic part to be very rough/bumpy, another to be slightly rough/bumpy, and another to remain smooth/untouched.
Let me be forthright and say I have no background here in textures/plastics/molds etc.,
Al my projects, settings and templates use the Metric system.
When i open the material physical properties i see the Imperial System.
How can i change this ?
why my facial control rig is not updating my character morph targets in real time? I would have to go into the modifier in order to see changes after clicking the slider. I used both the reaction manager method and the wired parameters but neither is working.
View 2 Replies View RelatedIs there a way to control which of two 'Graphic Property definitions' are used via a formula property with a IF, Then, condition statement?
View 3 Replies View RelatedI have two related properties... One is a formula property, the other is a manual property.
In the formular property I'd like to set the value of the manual property.
How can I see the mass of a solid, or if it's not possible, at least the volume.
View 1 Replies View Related