I can put a regular dimension to an intersection, but when I rmb I do not have the intersection option when placing an ordinate dimension. Is there another way to go about putting an ordinate dimension to an intersection?
View 9 RepliesThere was a message on here about using Ordinate Set to create an ordinate dimension to an apparent intersection and I've managed to do that, but is there a way to use just Ordinate to dimension to an apparent intersection? I've tried dragging and right click menu but no luck.
I'm using Inventor Professional 2012.
Inventor 2009....how to remove an Ordinate dimension (not Ordinate Dimension Set). It seems you can only make one per view. And you can only edit the dimension, i.e. the Origin symbol, but not delete it !? Don't know if there is a change from previous versions of Inventor to 2009.
View 9 Replies View RelatedI am running Inventor Professional 2011 and I have horizontal ordinate dimension, and what I need is to have Text above the Dim line and dimensions beneath it.
View 5 Replies View RelatedI am using inventor 2012. Is there a way to ordinate dimension angles? For example dimensioning an irregular bolt pattern in a flange.
View 3 Replies View RelatedHow do I rotate my value(s) on the vertical ordinate dimension vertical?
View 9 Replies View RelatedHow could I edit each ordinate dimension to basic or add for the selected dimension a tolerance? Is it possible to edit each ordinate dimension individually? How could I get the value of the selected dimension?
View 2 Replies View RelatedHow to rotate ordinate dimension text in Inventor 2014? Currently the dimensions are horizontal but I would like them to line up with the dimension lines (top and bottom dimensions are vertical)
View 1 Replies View Relatedhow to set my origin point to a hole center. When you create the first ordinate dimension, you have to set the origin marker. For the upper view, I want to set the origin to be the same as the view below it. I can set it to the end of one of the hidden lines from the hole, but I can't seem to set the origin to the center of the hole.
View 5 Replies View RelatedI'm trying to place my ordinate dimension to a theoretical sharp corner and the dimension will only go to the end of the arc (see pict). I try and drag the dimension end point by selecting the end of on line and dragging it over, select the other line and drag it till the two yellow dots meet at the intersection.
When I let go of the mouse button to place the dimension it pops to one side or the other of the arc.
When I place a centerline (or include a workplane from the ipt) is there ANY way to dimension to the intersection of this centerline and the edge of an object?
Like in this image above, I would like a horizontal dim between the vertical centerline and the intersection of the centerline and the edge of the part.I know that I can create a sketch on the view and project geometry/draw geometry... but that is such a pita.
How do we create dimension at an intersection point between arc and line?see attached picture. I need to create dimension as red line.
View 3 Replies View Relateddimension bend parts with corner intersection. Is there any option in Autodesk Invenor Drawing so that i can give dimensions as shown in attached image.
View 2 Replies View RelatedI am working with a point cloud and want a dimension that will call out the Z value of a selected node. Is there a way to adjust an ordinate dimension to report the Z value instead of Y? If not, is there another way to do this?
View 4 Replies View RelatedI am drawing ordinate dimensions in blocks and then I am getting the geometric extents of these blocks, if the block contains the dimension, the extents are much larger than expected. What may be the cause?
See the attached drawing, the lines are connecting geometric extents MinPoint and MaxPoint. For the blocks that don't have dimension in them, the extents are correct.
Currently, when I do drawings, I give my machinists drawings with each point, and they program their machines. To do that, they calculate the round part diameters, which is basically 5" - 2x<Dim>.
I'd like it if I could give them drawings with the real number, and in parenthesis next to it, 5-2x<Dim>.
I've attached a jpg of what I normally give them and how I'd like it to look. Is this something do-able via a macro or something?
We're having a problem with Ordinate dimensions. When we dimension to a radius corner, we dim to the "implied intersection" of the two lines, rather than to the center of the radius. We make a sketch with the two "tick marks", then dim to the intersection of the tick marks.
Ordinate dimensions are not allowing us to pick the intersection: it wants to put two (or three) dimensions, one to each end of one or the other tick marks (see attached). We use Ordinate dims about once a year, but I'm sure I remember being able to ordinate dimension to the tick marks.
I have had to revise a part that someone else created at some earlier date.They used the ordinate dimensions, which works perfectly and looks good.
I have had to add some holes to this part, but can not figure out how to add more dimensions to the existing ones, outside of deleting the dimensions and dimensioning them all over again.
How do I add more ordinate dimensions to the existing?
I design molds for the rubber industry and I was using Acad 2000; I am just now starting to use inventor. I need to used the ordinate dimensioning although I need the dimension to be given as a diameter and not as a radius. Is there anyway to scale the ordinate dimension automatically as 2:1? This way when I give the prints to the tool room they don't have to manually double every diametrical dimension. The prints that I draw only show half of the mold, there for needing a 2:1 dimension scale.
View 9 Replies View RelatedI use ordinate dimensioning on most all the drawings that go to our shop, but I've run into a problem setting 0,0 on one part.
Along the left side, is a straight edge, but the zero point along the bottom will be a point.
How do I use the point as my zero surface?
Lenovo Think Pad
Windows 7 SP 1
64 Bit.
Inventor 2013
ACAD Mechanical 2013
I have been using the ordinate set command to place set dimensions on an Inventor drawing in version 2012, I was looking for a similar way to rapidly add dimensions for hole diameters .
View 5 Replies View RelatedWhat distinction is between “intersection” and “apparent intersection” in snaps,. I’m not sure what difference is between the “intersection” and “apparent intersection” in snaps.
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
I am trying to create an intersection design using the Intersection Tools in C3D 2012. I followed the steps in the tutorials, created a corridor on the major road, splitted the regions, created the intersection and added it to the major road corridor, and connect the regions with the intersection portion.
I used the same assembly throughout the design just for simplicity, however, i notice that there are gaps of curb between the curb return section and the through section (as outline in red rectangles).
We use ordinate dimensions for all holes in parts. Unfortunately there seems to be features frequently left out of ordinate dimension mode. For instance, by default Inventor uses center and quadrant object snaps. Unlike in normal dimension mode, there is no right click option for disabling quadrant snaps. This is a constant annoyance, especially when dimensioning a print with a lot of holes. Is there any other way or hidden setting to disable the quadrant snap? In addition, add member is missing from the new "marking menu" completely so we have to enable the old right click menu to get it back. Are we the only ones using ordinate dimensions?
Inventor 2013 SP1.1 update 1
i am using inventor professional 2013.iam trying to align dimensions (ordinate) using ARRANGE COMMAND but not getting the result i desire.
i tried arrange command but it always aligns with respect to the square brackets .
I'm detailing a simple square plate with a good number of holes in it. I create an ordiate set running vertically along the LH edge and select the holes that are close to that side. Origin is the lower LH corner. Works great, easy.
The holes that are closer to the RH side though I'd like to show on that side. So I go to create a second ordinate set for the RH side and choose the lower RH corner as the origin and choose my holes that are close to that edge. The 2nd set will automatically show a second "0.000" dimension on the bottom edge and I can't supress it by right clicking.
Is there a better way to do this? What I've done now is to not use a set but just choose ordinate dimension and go from the opposite edge, which works.... But alignment is better with a set.
I have one problem in ilogic "How to convert the normal dimension to driven dimension through ilogic"
View 4 Replies View Relatedhow to make a radius dimension a diameter dimension? I have Inventor Profession 2013.
View 1 Replies View RelatedIs there a way to override a dimension and have it shown as a GD&T Basic dimension. I can override a dimension with the text option but not with a box around the letter. It sounds strange to do this but the letter represents a dimension in a chart format that are Basic dimensions.
View 9 Replies View RelatedIs there a way to make the linear dimension a diameter dimension?
View 9 Replies View RelatedWe need to be able to use intersection with radius... In doing, it just snaps to the center not intersection.
View 9 Replies View Related