I'm trying to constrain a length of ACME threaded rod to a nut so that when the rod is spun or threaded it shows it traveling into the nut as it will be grounded. I would like it to work as a driven assembly or if I was to turn or spin the rod by the mouse. I've reseached this for the last 2 days and can not spend any more time on it so time to ask the experts.
View 4 RepliesI have some problems with Bolt Connection Component Generator. For placement I choose Concentric, i choose all references, but I can't select Diameter. It is stuck to 10mm and i can't change it.
I am using Inventor Profesional 2013
After I create bolt connection by select the "termination" and all the fasteners, the length of bolt is fixed. How can I change the length of bolt?
View 1 Replies View RelatedI am trying to animate a couple slides in to show their motion. I setup each different position in a positional rep in my iam. They work correctly. Next I went to Studio and created an animation that went from one PR to the next. I am using the sequence like PR "A" to "B", then PR "B" to "C", then PR "C" to "D".
The trouble is in studio it does not work like it does in the assembly. Watch both videos to see what I mean. It is difficult to explain without being lengthy.
The video shown here is what I am trying to show in Studio. See the reply to this message to see my clip taken from Studio.
I made this sketch and the two marked dimensions were added when i pressed the Automatic Dimension and Constraints tool, because, in spite of all the dimensions i put manually, the sketch wasn't fully constrained.
Why wasn't it? it seems to me that i gave all the necessary information.
I need to have one assembly constrained to three places on along a bar. Should I ( and how would I?) open another assembly drawing, insert said bar and some how insert those three assemblies into the drawing?
View 7 Replies View RelatedIt seems there is a problem with Inventor 3D Sketching. I have a 3D Sketch, with 1 fully constrained vertical line, and another vertical line with an open length. I then join the 2 lines with a line on the top. When I give the top line an angle dimension, I expect it to be fully constrained, but it appears not as the line remains "green".
See attached file.
Windows 7
Inventor Suite 2011
Dell Precision M6400
Intel(R) Core(TM) Duo CPU 2.40GHz
RAM 12 GB
NVIDIA Quadro FX 3700M
Spatial Feedom - Astroid
i am beginer in Assembly,How i come to know whether my assembly is fully constrained or not?
View 2 Replies View RelatedThis assembly has piping parts that are not filly constrained yet will not move. For example a Tee that has only its centerline mated to a pipe centerline acts like it is fully constrained or grounded. I can demote those parts into a sub-assembly and then they behave normally. I'm wondering if this assembly has some kind of bug, even though no errors are reported and rebuild all doesn't work. Is there any kind of other program that goes through an assembly file and cleans up bugs? The pack n go is 65 MB.
View 9 Replies View RelatedI'm having trouble extruding a fully constrained sketch. The sketch is a cross-section of a hollow cylinder that is splined on the inside surface (see attached part file). The line segments that create these splines seem to be grouped together because moving one line moves the others, however the sketch will not extrude.
I can't use the coincident constraint button to group the lines because they don't separate from each other. I also tried to use the close loop button but was unable to select all the necessary lines.
how I can extrude this sketch or make an equivalent sketch that is easier to extrude
I am trying to constrain a point(on a different part) to the sketch(yellow) on the inside surface of the triangle part. If I try the constraint like how it is now, it only allows me to select one segment, not the entire triangular shaped line. It would work if inventor saw the sketch as one single element, but it of course does not. I tried making a 3d sketch of the inner surface and then constraining to that, but it did not work.
View 3 Replies View RelatedI read what is in the picture in a skill builder, which is:
[URL]
When is a sketch that is copied to another part file linked to the source file?
I tried it, i copied part of a sketch, some lines, from one part file into a sketch in another part file and there was no link
Coming from a background of ProE, Usually a mirrored group of constrained parts would mirror with alternative constraints locking them in place. Is there a way to do this in Inventor?
Every time I mirror constrained parts through a Datum plane, the results are loose components that could be dragged anywhere. I might aswell have just placed them again, though it gives me a good idea of where they should be.
Without grounding them, is there someway of locking these compents in the mirrored position.
Also, bolted connections pick up on patterned holes and populate them, yet there is only one constraint to the original hole and the rest can rotate around it.
How to add a Thread to both the Nut & Bolt....i always use the Thread Tool but i would like to also know how to add an actual thread.
View 2 Replies View RelatedHow to use dynamic simulation, i am creating a bench vise and woud like to animate it going in and out how would i do that?
View 1 Replies View RelatedI've assembled a bolt and a slide block that is constrained to a base plate and am able to put everything in motion. I have the slide block constrained to slide the distance of the base plate and when I reach the end the bolt continues to rotate when, if this was a real part, should stop. How can I get this bolt to stop once the slide block reaches its ending constraint?
View 2 Replies View RelatedI'm working on a project in wikiHelp under Inventor tutorials, Content Center, Create iMates. When I pull the object up in an assembly I can create an iMate and it will show that I made one. But when i go to the next page (Place Content Manually Using iMates), I can't get the bolt to snap to the iMate inside the object, the bolt just stays in one position the whole time.
View 2 Replies View RelatedCurrent version INV 2012
1. When placing pumps,bolt-on walkways etc..etc..on to a metal frame at the assembly level do you place the pumps/walkways first and then add the bolt holes to the frame or do you create the bolt holes first in the frame and then place the pump/walkways on to the holes?
I want to insert from content center a screw and modify it, prolong it's thread and more.How can i do that?
In a part file i cannot insert parts from content center, should i make an assembly? and then?
When inserting a bolt connection requiring a coutersink or counter bore, the bolt is not placed flush and is left standing.
View 8 Replies View RelatedMy after effects is not showing the full bezier curve. The star is supposed to bounce from upper left to upper right.The curve is cropped. How to adjust this?
View 1 Replies View RelatedUsing bolted connection, I want to place a bolt through 3 sheets of metal. The first 2 sheets i want it to automatically place a slightly larger hole (which it does) but I want the 3rd sheet to be threaded so the bolt thread and hole thread are the same size.
View 3 Replies View RelatedI can not use rectangular pattern for bolt in an assembly.
View 7 Replies View RelatedWhen a bolted connection is used, the bolt changes in length as the stackup of hardware increases and decreases. I have noticed that if I do not grab the red arrow to adjust the length, the amount the bolt extends past the nut
seems to be only about 2 threads. What is the formula Inventor uses to determine this extended length?
I've been working with Inventor 2011 - Pro and have not had any success with utilizing a bolted connection (blind hole) in an FEA stress analysis. I have reviewed and one suggestion involved a using a bolt placed "as custom" instead of "as standard". It appears however that there is a default setting that I currently have which doesn't allow this as a selection.
View 4 Replies View RelatedI starting out new to Inventor 2013.What are the steps to place a washer and bolt from Content Centre into the assembly?
View 5 Replies View RelatedI have a ratchet plate idw that I've drawn and dimensioned, but I would like to insert two bolt circles to the two diameter dimensions that appear to be pointing at nothing. The circular pattern is not made up of circles so I haven't been able to use the Centered Pattern command in the centerline section. I'm using Inventor 2013.
View 3 Replies View Relatedis there a way to Replace the "bolt" Component Occurrence with api?
View 2 Replies View RelatedMy Stress analysis will run and process after i hit simulate but did not return result(Results tree is empty)
I'm running autodesk inventor pro 2013.
In my work i normally use our standard full threaded rods with square nuts. But, since we make the rods and nuts in the factory, they do not follow any international standard.
I wanted to add the threaded rods to the Bolted Connection menu in order to be able to automaticaly add the rod and to let inventor calculate the needed lenght.
I was able to add the rod to content center as an Ipart with all available sizes, but it doesn't appear on the bolted connections menu.
See attached our normal bolted connection, how can I add this to bolted connection so inventor will size it automatically to the needed lenght?
Im using the bolted connection tool and when i chose all of circluar reference and pick out my bolt and nut the tool will only draw one bolt and ignore all the other circular references. It previews all the bolts just fine ut will only place a bolt in one of the circular references.
View 7 Replies View Related