I have some problems with Bolt Connection Component Generator. For placement I choose Concentric, i choose all references, but I can't select Diameter. It is stuck to 10mm and i can't change it.
I am using Inventor Profesional 2013
After I create bolt connection by select the "termination" and all the fasteners, the length of bolt is fixed. How can I change the length of bolt?
View 1 Replies View RelatedIm using the bolted connection tool and when i chose all of circluar reference and pick out my bolt and nut the tool will only draw one bolt and ignore all the other circular references. It previews all the bolts just fine ut will only place a bolt in one of the circular references.
View 7 Replies View RelatedI have a frame member and a plate bolted together using the bolt connection feature. I moved the frame member slightly and while the bolt and nut moved the hole in the plate did not. Do I have to redo the connection when I adjust the position of parts to get the hole to stay in line with the bolt?
View 3 Replies View Relatedis there a way to Replace the "bolt" Component Occurrence with api?
View 2 Replies View RelatedI have a problem acessing the fatigue calculation panel in the bolt connections´ tool. Whether I press enable or disable I simply can´t acess it. What should I do to access it?
View 4 Replies View RelatedHow to add a Thread to both the Nut & Bolt....i always use the Thread Tool but i would like to also know how to add an actual thread.
View 2 Replies View RelatedHow to use dynamic simulation, i am creating a bench vise and woud like to animate it going in and out how would i do that?
View 1 Replies View RelatedI've assembled a bolt and a slide block that is constrained to a base plate and am able to put everything in motion. I have the slide block constrained to slide the distance of the base plate and when I reach the end the bolt continues to rotate when, if this was a real part, should stop. How can I get this bolt to stop once the slide block reaches its ending constraint?
View 2 Replies View RelatedI'm working on a project in wikiHelp under Inventor tutorials, Content Center, Create iMates. When I pull the object up in an assembly I can create an iMate and it will show that I made one. But when i go to the next page (Place Content Manually Using iMates), I can't get the bolt to snap to the iMate inside the object, the bolt just stays in one position the whole time.
View 2 Replies View RelatedCurrent version INV 2012
1. When placing pumps,bolt-on walkways etc..etc..on to a metal frame at the assembly level do you place the pumps/walkways first and then add the bolt holes to the frame or do you create the bolt holes first in the frame and then place the pump/walkways on to the holes?
I want to insert from content center a screw and modify it, prolong it's thread and more.How can i do that?
In a part file i cannot insert parts from content center, should i make an assembly? and then?
When inserting a bolt connection requiring a coutersink or counter bore, the bolt is not placed flush and is left standing.
View 8 Replies View RelatedUsing bolted connection, I want to place a bolt through 3 sheets of metal. The first 2 sheets i want it to automatically place a slightly larger hole (which it does) but I want the 3rd sheet to be threaded so the bolt thread and hole thread are the same size.
View 3 Replies View RelatedI can not use rectangular pattern for bolt in an assembly.
View 7 Replies View RelatedWhen a bolted connection is used, the bolt changes in length as the stackup of hardware increases and decreases. I have noticed that if I do not grab the red arrow to adjust the length, the amount the bolt extends past the nut
seems to be only about 2 threads. What is the formula Inventor uses to determine this extended length?
I'm trying to constrain a length of ACME threaded rod to a nut so that when the rod is spun or threaded it shows it traveling into the nut as it will be grounded. I would like it to work as a driven assembly or if I was to turn or spin the rod by the mouse. I've reseached this for the last 2 days and can not spend any more time on it so time to ask the experts.
View 4 Replies View RelatedI've been working with Inventor 2011 - Pro and have not had any success with utilizing a bolted connection (blind hole) in an FEA stress analysis. I have reviewed and one suggestion involved a using a bolt placed "as custom" instead of "as standard". It appears however that there is a default setting that I currently have which doesn't allow this as a selection.
View 4 Replies View RelatedI starting out new to Inventor 2013.What are the steps to place a washer and bolt from Content Centre into the assembly?
View 5 Replies View RelatedI have a ratchet plate idw that I've drawn and dimensioned, but I would like to insert two bolt circles to the two diameter dimensions that appear to be pointing at nothing. The circular pattern is not made up of circles so I haven't been able to use the Centered Pattern command in the centerline section. I'm using Inventor 2013.
View 3 Replies View RelatedMy Stress analysis will run and process after i hit simulate but did not return result(Results tree is empty)
I'm running autodesk inventor pro 2013.
In my work i normally use our standard full threaded rods with square nuts. But, since we make the rods and nuts in the factory, they do not follow any international standard.
I wanted to add the threaded rods to the Bolted Connection menu in order to be able to automaticaly add the rod and to let inventor calculate the needed lenght.
I was able to add the rod to content center as an Ipart with all available sizes, but it doesn't appear on the bolted connections menu.
See attached our normal bolted connection, how can I add this to bolted connection so inventor will size it automatically to the needed lenght?
I'm trying to assemble two parts, each of which has four matching bolt holes.So I do a "mate" between a hole on one and a hole on the other. This works fine, and the parts now behave just like two parts bolted together with one bolt - one can be rotated relative to the other around the bolt hole. So there is one degree of freedom left to be constrained.
But the obvious ways to constrain that one last rotational constraint result in overconstraint. Trying a "mate" between the circles at the ends of the corresponding bolt holes breaks the first constraint, and the non-grounded object "jumps". Trying to auto-mate the two holes results in the holes being constrained as tangent, with the holes not lined up. I've tried constraining the center points of the end circles of the holes. That doesn't work right either.
Doing the second constraint as "tangent-inside" does work. That's a 1 DOF constraint, which makes sense.It took me a while to figure that out. The help files aren't very useful when multiple constraints are involved.
I want to use a certain bolt from Content Center. Unfortunately, the particular size I want to use does not exist in the content center, but it does exist at one of our suppliers. How can I add this size to Content Center?
Or, can I somehow check out this bolt as an iPart, and then I can modify it (add any size I want, or even make it custom) according to my will?I am using Inventor 2013
I want to change the description of a bolt to be "M(bolt size) bolt. then add the length in another column. example M10 bolt.
I want to know if it is possible to do this using the Family Properties & changing the "Family Description" to something like M=<NND> BOLT. i have tried but had no luck as it only comes back with "M Bolt" & no diameter
Any other way to make it populate a BOM easily.
The problem is simply reconciling stress analysis results with hand calculations and I suspect I'm simply setting up constraints incorrectly or something.
A simple problem of an M6 bolt in single shear as in the image below. I am using the formula in image to calculate the shear stress. The diameter (being an M6 bolt) is 6mm and hence radius is 3mm with a shear force of 1000 N being used. Using the formula in the image below and the figures above, I calculate the shear stress in the bolt to be 35.4 MN/m^2 or 35.4 MPa if you prefer.
My problem is that when I simulate this problem in Inventor 2013 stress analysis the results (for any kind of stress analysis; Von Mises, 1st and 3rd principal, all the planes etc...) are way way off what the hand calculation is, ranging from 160 MPa to around 800 MPa.how to set this example up in Inventor correctly so that you get the same (or near enough) result.
At my workplace it has been standard practice in Autocad to call out bolt assemblies in a parts list as: 1/2-13 unc hex hd. bolt w/flat washer & nut. How to do this in Inventor? I know I can enter this info on the assembly iProps for the bolt assembly, I was hoping someone came up with an automated format, maybe pulling info from the bolt itself to populate the assembly iProps?
Product Design Suite Ultimate 2014
Vault Professional 2014
Windows 7 Pro SP1
HP-Z400: 2.67 GHz 12 Gb Ram
Nvidia Quadro FX1800 driver 276.42
I want to change the bolt form "M8×80" into "M8×50". How to realize the function in my VB program make use of API?
View 1 Replies View Relatedhow I can get the bolt type and sizes to show in the description of the item in a parts list when placed through Content Center! I would like the same with all fixings.
We have configured our own Content Center by copying standards and replacing the part number with our own reference number. This then shows the description as "Bolt" with no size etc.
Can Content Center be configured in a way to show sizes in description?
trying to draw a hex nut in isometric...I've got the ellipse with the inside/outside dimensions but as far as placing the lines and connecting them to make the hexagon perimeter I keep coming up wrong..
View 3 Replies View RelatedI'm trying to make a dynamic bolt that has a nut on it that can move back and forth but is constrained to the max distance set by the bolt length. I want one line type between the head of the bolt and a different line type between the end of the bolt and the nut.
Currently if I take my nut past the end of the bolt, the lines are all messed up?I'm new to dynamic blocks but liking them.