I have a bar and I want to place there several clips so that they are only moveable in one direction. Both of the parts have fitting iMates. When I place the first clip it works fine and the iMates get connected. But when I place the second the clip is draw elsewhere. Is it possible to use one half of an iMate more than once?
View 1 RepliesOkay so i saw a video on how to set up iMate for Vex Robotic parts (circle and square fitting), and i cant get the circle to do a surface extruding. Any reason whats going on? I followed the video's instructions perfectly, and still nothing is working. URL...
View 2 Replies View RelatedIs there a way to put a bunch of imates under one line code?
I have imate iInsert:1 thru iInsert:49 I need them all suppressed when an event happens.
I can get it to work one by one but that would be a lot of code.
Tried a few other thing but seems not to work.
2012 Factory Design Suite ( will not load 2013)
i am trying to add some items in the iMate matchlist. But with the code i use below i recieve a runtime '10' error:
This array is fixed or temporarily locked.
Function PlaceiMates()Dim oApp As ApplicationSet oApp = ThisApplicationIf ThisApplication.ActiveDocumentType = kPartDocumentObject Then Dim odoc As PartDocument Set odoc = oApp.ActiveEditDocument Dim oInsert As Object Dim oInsertiMate As InsertiMateDefinition Set oInsert = ThisApplication.CommandManager.Pick(kPartEdgeFilter, "Pick Edge for Imate") Set oInsertiMate = odoc.ComponentDefinition.iMateDefinitions.AddInsertiMateDefinition(oInsert, True, "0mm", , "Test") Dim ml(1) As String ml(0) = "pl" oInsertiMate.MatchList = mlEnd IfEnd Function
I'm working on a project in wikiHelp under Inventor tutorials, Content Center, Create iMates. When I pull the object up in an assembly I can create an iMate and it will show that I made one. But when i go to the next page (Place Content Manually Using iMates), I can't get the bolt to snap to the iMate inside the object, the bolt just stays in one position the whole time.
View 2 Replies View RelatedWhen I place a part, such as a bolt, from the Content Center, it's immediately looking for the other half of an insert iMate. How do I make a part I created do that? I put an iMate in the part, but it had no effect.
It sure would save a bunch of time if this would work.
Infrastructure DSP '14 / Product DSP '14 / Vault Professional 2014
Dell Precision T1650
Windows 7 Professional SP1 64-bit
Intel E3-1270 V2 3.5GHz / 32G RAM
Nvidia Quadro 2000, Driver 331.82
Space Navigator, Driver Version 6.17.7
When I am inserting in an assembly two parts with I-mates and the name's of the I-mates are not matching they are acting of the name's are matching. So the two parts are constraint with the not matching I-mates.
View 7 Replies View RelatedHow to derive only referenced imates to the solid from multi body part.
View 6 Replies View Related(Inv Pro 2012, XP64, Vaulted Project and Content Center)When I'm placing hardware, the Autodrop function is really convenient. Even better when the "multiple" pickbox is active, which from what I understand is when Inventor finds similar features on the same plane that the selected autodrop component could potentially mate to.
This is a huge time-saver, since I often have lots of bolted joints that all terminate on the same plane. Sometimes however, even when the parts lie in the same "plane", the plane isn't contiguous in that a feature breaks it across. No biggie, it just means I have to do two or three "multi-autodrops".
Once I put washers at the back side of the connections (which multiple works like a charm on), all of a sudden when I go to place nuts, each washer surface is now it's own plane, and multi-drop no longer recognizes all the other parts. This can be a real pain manually placing 30 or 40 nuts at a time.
I think the "Bolted Connection" option might work, but I really don't have a need to store all those subassemblies, name them, keep them vaulted properly, etc. That would be almost as much of a headache.
Also, most of the features that I'm connecting through are created as Hole features and as "nominal" oversized bolt holes as Inventor suggests when the "clearance hole" option is used for hole creation (not randomly extruded islands), but they aren't patterned as they don't follow a prescribed circular or rectangular pattern.
Am I missing something that I can do (like something stupid simple such as holding down the "alt" key or some crazy thing like that) that will allow inventor not just to suggest CONTIGUOUS planar features, but also CO-planar features so I can place all these nuts at once?
Short of creating a custom Content center part that consists of a nut / washer assembly I can't think of anything. And creating and publishing the nut washer assemblies will eat up some time too, since I have about 50 different combinations (some SAE washers with normal hex nuts, some SAE washers with ESNA hex, some USS washers with jam nuts, some USS Type B washers with all-steel locknuts, etc...)
I'm designing a part that in Autodesk Inventor 2013 that is constructed from several layers laminated together. I have 4 layers:
F (front)
M1 (middle, variation one)
M2 (middle, variation two)
B (back)
The final solid will lhave 17 layers laid out like this:
F | M1 | M2 | M1 | M2 | M1 | M2 ... | B
I currently have a part file containing
F | M1 | M2
What's the best way to create this solid if I want to a) keep all instances of M1 and M2 in sync, and b) make it easy to work on all 4 layers. Do I have to export F, M1, M2, and B as individual parts and import them into an assembly or can I keep them in one part file? I really like the ability to be able to work on all the solids at the same time because they're visually dependant on each other.
From all our parts of an assembly we made 1 IDW with multiple sheets. Now we want to convert this IDW to PDF's and in such a way that we have one PDF for each sheet, and each PDF files needs the same name as the sheet.
View 5 Replies View RelatedWe have a frequently used bearing assembly for dampers, mounted to plate consisting of a shaft hole w/ 2 countersunk holes for flat head cap screws to mount the bearing.
I have a stamp for the hole array into the plate, and can individually i Mate each FHCS into said holes after placing in the assembly onto the plate.
Is there a way to set up the iMates so that the bearing assembly would plop in automatically into the two separate countersunk holes? Not sure if you would have to create iMates in the stamp...or if thats even possible.
Sometimes the damper may have 2 bearing assemblies @ opposite side of the frame for one blade shaft, sometimes we may have as many as 4-5 blade shafts (10 bearing assy's). So Im imagining dragging the thing to each iMated array and dropping it in.
Inventor 2014
Windows 7 Pro SP1
Intel(R) Core(TM) i7-3770k CPU @ 3.50GHz
16GB RAM
NVIDIA Quadro 4000
3D Connexion SpaceMouse Pro
Is there any way to cause Inventor to convert a multi-sheet IDW to an Autocaf DWG file that puts each IDW sheet on it's own tab in the dwg?
IDW ---Sheet 1, Sheet 2, Sheet 3, etc
DWG - Tabs for Sheet 1, Sheet 2, Sheet 3, etc ALL IN ONE DWG FILE
This so we can do batch printing and not have to maunually assemble dwg file with multiple tabs from the individual dwg files generated by Inventor - as near as I can tell, there is no way to get Inventor to NOT create a separate dwg for each sheet in the IDW???
As the subject line says, when multiple instances of Inventor are open on the same machine, the addin will only show in the first one. I do not see any errors generated and tried many approaches. I tried to use the ribbon abpannelcontrol
created by the first instance. Or in every subsequent instance of Inventor to delete the existing ribbon abpannelcontrol, and recreate them from scratch. Both approaches did not work.
I have a spring that is used in multiple assemblies and in each assembly the compressed length is different. Plus the amount of compression is different.
What is the best way to model the spring so if I change the WD or OD, etc. all assemblies would update?
I tried adaptive, but that seemed to limit the relationship to a one-to-one not a one-to-many.
If I used iPart or the spring was derived from a table, where the OD & WD were constant, would the assembly models change when I changed these values?
I have attached a pic of what I am trying to accomplish.
The part was done in SW, but I am now needing to do it in Inventor.
I have a flat plate, 12" square, that I am needing to bend the 2 corners up, with 10 1/2" between bend lines.
I tried using the "BEND PART", but I can only select one line. What should I use so I can bend all four sides up?
Lenovo Think Pad
Windows 7 SP 1
64 Bit.
Inventor 2013
ACAD Mechanical 2013
Is there any way in inventor to use one extrude cut feature on two different solids at the same time?
View 9 Replies View Relatedi'm looking for a command,activex,plugin,vba ,c++ ,any external program or cut a solid object in multiples slices using paralel and equidistant cutters planes, like a tomography.
View 3 Replies View RelatedI have a project and I use dynamic simulations to check the working of the model. I want to use different simulations, with different forces on different parts.
But I see no possibility to create different simulations like a can create different FEM analysis situations. So can I create different dynamic simulations for one project?
I have an assembly with multible parts which all have iLogic rules in them. I want to controle when the rules are executed in each part, thus I have set them as "Don't run automatically". These rules are iTriggered by the top assembly, if they are active.
Is there a possibility of how I can run multiple rules simultaneously?
The code below is an example of the controle rule that determines the rules to be run but it takes one rule at the time...
IfComponent.IsActive("5580 Heating element package 1")=TrueThen
iLogicVb.RunRule("5580 Heating element basket 1", "iTriggerRule")
EndIf
IfComponent.IsActive("5580 Heating element package 2")=TrueThen
iLogicVb.RunRule("5580 Heating element basket 2", "iTriggerRule")
EndIf
.
.
.
up to x
I have also tried with For - Next statements...But the rules are run in the order that tey are written...
As the computer has a lot of memory in reserve; I want somehow all the iTriggerRules to be run at the same time as this would save a lot of time.
Is there a way to select more then one component when patterning in an assembly?
View 5 Replies View RelatedI have a BOM that shows up as in units for length items and unitless for qty items. When I change the UOM to use FT units the non-length units get inch ticks. The qty 1 which means I need one shows up as 1" where I do not require a 1 inch part but one each. How do I remove the inch ticks?
View 5 Replies View RelatedDid the ability to add multiple envelopes to a single part not make it to 2014? In the demo video from Autodesk it shows you can do that but I don't see that button in 2014?
Running 2014 Product Design Suite Ultimate
Windows 7 64 bit
90G OCZ SATA 3 SSD (My SSD is faster than your HDD)
Core I7 920 processor, ATI HD6970 graphics card, 12G Corsair RAM
I have a multi sheet drawing I am creating. My BOM is on the first sheet.
I have noticed that when I place views on my subsequent sheets, the balloons restart from item 1 again. Is there a way to link them to the BOM on sheet 1?
(Colossians 3:23-25)
How do I prevent Inventor from opening files in new Inventor sessions?
If I try to open a file from Windows Explorer or from an email attachment, it opens it up in a brand new Inventor session, even if I already have Inventor open.
If I select two or three files in Windows Explorer or from an attachment to open, it opens them all in individual new Inventor sessions.
I would like to set Inventor (or Windows) so that these files open in the already existing session or at least the same session as each other. I didn't have this problem before upgrading to a new computer and reinstalling.
I'm creating an assembly and in this assembly I need to add some foam pieces. These pieces are the exact same part number but can vary in length. How can I make such a part so that i can insert it into an assembly multiple times but have different lengths? I'd rather not make multiple pieces of foam for every single assembly for all of our product lines and am looking for the "one foam to rule them all" option. I would assume this would be an ilogic component I would have to create, but i haven't really made a part like that yet.
View 3 Replies View RelatedI need to convert some of my ipt files to stp (around 130 files). Is there any way to do it all at once?
View 1 Replies View RelatedIs there a way to allow Inventor 2013 to copy multiple objects when executing the 'copy' command ? Similar to in AutoCAD where you can continue to copy objects in multiple instances instead of it terminated after a single copy ?
Autodesk Inventor Professional 2013 SP2 64-Bit Edition
Windows 7 HP Z400, Intel Xeon W3550 3.07GHz
12.0GB RAM, ATI FirePro V4800 (FireGL)
how to cut or split more than one face of a surface model in one go. The only way (it seems) is to use the Trim command for every face you need to trim, whereas I want to choose the cutting tool (a plane or face) and then choose a whole lot of faces (by holding CTRL and clicking the faces) and trim them all in one go. Is this possible? I can do this in Fusion, but Fusion is way too slow on my PC compared to Inventor.
I also tried extruding a sketch through the surfaces to cut them, but it doesn't work (Inventor complains that there aren't any solids to cut).
Can I save multiple drawings to dxf in same time? I`m so tired to click "save copy as" with every drawigs. Autosave with flat pattern is not an option because orientation of the piece is so bad so many time of the cases
View 9 Replies View RelatedI have a VBA macro that places selected virtual components into an assembly. I can place virtual components with different part numbers into the assembly with no problem. When I try to place the second instance of a virtual component with the same part number I get an error.
For example: If I place a virtual component with the part number C123A456 into an assembly it shows in the tree as C123A456:1 If I try to place C123A456 again it errors at this line.
'Add selected line as a virtual part
Set oOcc = oOccs.AddVirtual(sPartNumber, oMatrix)
I can place multiple virtual parts if I append -1, -2, -3 etc to the part number but I would like to let Inventor use the :1, :2, :3 to keep track.