AutoCAD Inventor :: Move Part Along Curve With Chain Drive In Assembly
Oct 4, 2012
I have two set of chain drives connected to each other through a common axle. The motor (which is not visible in my assembly) drives the yellow sprocket.
The two sprockets mounted on the grey axle is attached with a key way so when the yellow sprocket turns, the two chain drives turns.
I want to attach the blue sled on the blue chain, the red sled on the red chain and then rotate the yellow sprocket so both of the sleds moves with their chains (at the same speed/ time).
The blue sled is going to move a rolled bar (the orange one) on the floor (glass square) a certain length and then the red sled is going to "take over" and continue to move the bar on the floor.
I want to make sure I´ve got the spacing between the sprockets in the short chain drive (red) correct so the red sled takes over when the blue sled disappears under the floor.
[URL].....
[URL].....
[URL].......
[URL].......
Edit: I use IV 2012, but I also downloaded IV 2013 professional (trial) so I can use the dynamic motion.
I have finished all my parts and now i have to assemble them. I normally just use the constrain tools, but this time i need to set a part in mid air. I would like to use the move tool, but with exact xyz coordinates. I only seem to be able to do that with an UCS (coordinate system), not the part itself. I guess it's just a button i'm missing somewhere.
I noticed when creating assemblies, applying a positional constraint, the parts don't move. In order to get the parts to "move" to their constrained position I have to try and drag them with the mouse then they snap into place. Also updating the assembly works as well.
What setting could I have changed so that once I press apply on a constraint it moves the part immediately?
Dear Sir, In particular project, when I insert part in Assembly file, It is inserted as a Tube & Pipe run part. so that It is not Grounded automatically. What is the settings by which I can insert as a normal part in assembly file ? I have attached herewith the JPG file also.
I`m looking for the iLogic code that can change one parameter (user defined) for each (ipt) part in assembly (iam)
The one below doesn`t work.
Sub Main Dim oApp As Inventor.Application = ThisApplication Dim oAssy As Inventor.AssemblyDocument = oApp.ActiveDocument For Each oSubDoc as Inventor.Document In oAssy.AllReferencedDocuments On Error Resume Next Parameter(oSubDoc, "FH") = 15.26 Next End Sub
I would like to simplify this assembly into one seamless part for FEM calculation:The assembly consists out of parts that, in reality, will be welded together. Due to their form, there is no way to place them exactly onto each other, therefore there are slight gaps between the parts:
Now when I try to merge the assembly into one part via "simplify" --> "create simplified part" and choose "single solid body with seams between planar faces merged", Inventor does not fill these gaps (even though it displays only one part in the bottom right corner of my window). Unfortunately, the remaining gaps brings "contact" problems in the FEM simulation.
how to close the gaps and really merge the assembly into one part?
I have a part that has protrusions. When i mate that part up to another part that second part needs to have cutouts/holes to receive those protrusions.
i mainly use it in sheetmetal parts. and use the rectangular protrusions on de contour to mate up with corresponding cutouts in the other sheet. this works with positioning and also makes for a nice weld spot/area.
But also for making holes to accommodate a mold pin used in custom punch dies. I want the intervening part to receive a corresponding (propperly tolleranced) hole automatically. Much like a bolted connection does.
same for parts like circlips. i want them to automatically generate the seat in the part it's mated to. Rather than using the axle generator.
Ofcourse one can place the parts and do an in assembly interpart projection and go from there, but i want the part to generate the (predifined) modification to the other part. It would save time and also reduces problems as the parts are moved about or even removed.
I have an assembly with 10 parts in it. We use many assembly features at the assembly level (Revolve cut, Extrusion cut..etc). How to find the mass difference of each part by comparing at its parts level and its assembly level.
I have a two part duct fire damper assembly. The IDW has the combined two part assembly, which I know how to turn the CoG on, so that it can be dimensioned. The problem is each piece will more than likely be hoisted separately so I would like to show the CoG for each piece, not the combined master assy.is there a way to do this?
Inventor 2014 Windows 7 Pro SP1 Intel(R) Core(TM) i7-3770k CPU @ 3.50GHz 16GB RAM NVIDIA Quadro 4000 3D Connexion SpaceMouse Pro
Why when I mirror a part in an assembly the mirrored part gets a new part number? I want to mirror only the position of the part which is always the same part. Is it possible to do that in Inventor?
When I record an animation in .avi using the Drive Constraint command here's what pops :
-The codec you selected to compress this AVI video stream cannot handle the current screen color depth and/or the graphics frame size. Please try another codec.
-Then I press OK and it records but the AVI file is empty and no video is watchable.
What can I do?
I'm using Autodesk Inventor 2012 ans a windows 7 64bit brand new computer with Nvidia graphic card.
I have a frame generator assembly that I created to take advantage of the frame analysis tools. This assembly was later broken down into the main fabricated assemblies (for drawing purposes) using the "demote frame generator component" tools. The basic question is this: can I take one of the "demoted" sub-assemblies and move it to another assembly file all-together?
best way to move the four legs from the platform assembly to the tank assembly after the fact? I was thinking I would just place the leg sub-assembly into the tank assembly and then delete it out of the platform one but I'm not sure of the ramifications.
Inventor Professional 2013 (SP-2.3), Product Design Suite Ultimate Desktop: Intel Core i7 3.4GHz, 16.0 GB RAM, Windows 7 Ultimate SP-1, 64-bit OS, (2) GeForce GTX 580 (331.81), Space Pilot Pro (3.16.1) Laptop: Intel Core i7 3.9GHz, 16.0 GB RAM, Windows 7 Pro SP-1, 64-bit OS, GeForce GTX 780 (331.81), SpaceNavigator (3.17.7)
I have a sub-assembly that is flexible, (constrained properly, not grounded) and when I try to move it in the main assembly, I get the "universal NO" symbol attached to my cursor. There are no constraints preventing the movement in the sub, since I can move it however I want when the sub is opened.
I insert parts in an assembly, new parts from content center or from a library, without projected edjes, they are free to move until i impose the first constraint, the axis to axis alignment of round parts, then i cannot move them anymore in order to continue constraining them
I have an assembly of stair made from steel. There are lots of part the same. Is there a way to make a hole (inside assembly) to one and that hole would appear on all of them.
And another problem, how can I made cut (inside assembly) through more then one part so that would affect a part also when I open it alone.
I am capturing a book-case design that I made long ago into Intentor. I am almost finished, and I want to produce .dwg files and a bill of materials of parts that can be held.
For various reasons, almost all the items in the existing design are assemblies, and the underlying parts correspond more or less to half of physical parts that are contained inside a repeating cell. I will almost certainly continue using this approach.
A simplified design that shows this is at [URL]..... in the file Display.iam
I created the file Slat.ipt by using derive (Slat.iam).
If I replace the Slat assemblies with the file Slat.ipt, the bill of materials will show parts that correspond to physical parts that I can hold in my hand, or list on an invoice. I can do this with many, many mouse operations.
To make this modification quickly, I attempted to do Component -> replace on the Slat assembly. I use this operation a lot to replace one version of an assembly with another. When I do it with a .ipt file, the system pauses for some tens of seconds, then crashes.
A brute force work around is to use the mouse to do the replacement, essentially rebuilding the entire project in place.
as you can see from the image, the blue cone isnt transparent. i set the material properties to "clear blue" to make it "see through", i want to show whats under the cone. however the cone isnt transparent. how can i get the cone to be transparent? is there a step im missing?
I have written a program where i will copy inventor assembly tree to custom form in tree format. Now my problem is whenever i click a part in tree i must edit the part. I am trying to access the Fx parameter/IAssembly to use it but not getting desired results .
I need to use parameters of a part in an assembly. How to do this? Do i need to define a rule? How is this done?
Can i do it without using an Excel sheet as a parameter source for both the assembly and the part? The target is to have inventor update an array of assets as soon as the width of a part is changed whether in Excel or in the Factory properties of the asset.
I have an assebly where i have imported parts and other assemblies. Unfortunatly during process of assigning them together they have rotated by various angles.Is it possible to somehow "reset" the rotation of part according to global xyz?
My need is to assembly parts into an assembly by a known position in the assembly. The part has a UCS and I create UCS on the assembly programatically. What I cannot do is to constrain the two UCS. I tried this (Inventor 2013 x64 on W7/W8 64, c++ 2010 by the way DEBUG mode is not working from the IDE):
