AutoCAD Inventor :: Home View After Finishing A Sketch
Feb 5, 2011
i can't find where to tell inventor to not switch back to the home view after finish a sketch edit. sometimes it is handy but often it is nice to see the part update after doing some sketch editing rather then the home view spinning the part away. i think we are capable of hitting F6 ourself if we wanted that view.
i have found that inventor 2011 will always do this when you are looking square onto the sketch and then finish the sketch . am i right to say that this is only a 2011 thing? i cannot recall previously this happened. i am finding that i am always finishing my sketch and having to hit F5 after inventor swings away to home view.
I've checked everywhere else for a solution but none apply to me it seems. My keyboard shortcut for returning to the home isometric view (F6) is not working. F3, F4, & F5 all work fine. I've tried returning the cursor focus back to the model window and that doesn't work. I also made sure the shortcut is actually listed in the Customize menu, I even reset all to default in case something was changed.
I'm trying to retrieve a Camera Object for the "Home View", without setting the view to Home.
I use the "UserInteractionDisabled=true" in a addin to make sure the user doesn't mess with the inventor while my addin is doing some time consuming work.
When documents are open in this mode, the view is set to front. The only way I have found to get the camera for Home View, is to use the GoHome method on the ActiveView, but this is slow since it is running an animation...
Roughly im doing the following:
Inventor.UserInterfaceManager.UserInteractionDisabled = true;Document invDoc = Inventor.Documents.Open("c:\somefile.ipt");View v = invDoc.Views[1];v.GoHome(); //would like to not do this, it is animatingCamera cam = v.Camera;//cam.ViewOrientationType = ViewOrientationTypeEnum.kDefaultViewOrientation; //<- this will fail.. Point eye = cam.Eye; Vector up = cam.UpVector.AsVector();Point target = cam.Target;
Is it possible to get the Camera object for Home with "going" home?
I need an urgent solution to my issue.I have created section view from a sketch (a line constrained to the projection of a work plane) from my derived part to my drawing using the "Get model sketches ". When i update the iassembly and update the the view using model state the view tries to update but throws an error see attached document.When i delete the section line and create a section line manually ie. by creating a normal sketch in the drawing the same model gets updated without any error.
When I edit a part directly in an assembly, clicking on 'edit sketch' (frequently) changes the view from the one I had set while looking at the assembly. Is ther any way to turn this OFF?
I just installed the trial version of Inventor pro, 2013. I'm having a problem with the view changing on creation of a sketch. It goes to the home position. The "Look at sketch plane on sketch creation" is un-ticked in options.
Click on Component->Create. Once the Component is created, click 2D Sketch. View spins to the Home position. This is really annoying. I learned Inventor 2010 in school. I don't remember this ever happening.
If I select a plane from the browser prior to clicking the Create 2D Sketch, the view remains the same as expected. This is only a problem if you want to create the initial sketch using a face of another part as the sketch plane. Is there an option I'm missing?
I attached a sketch to a view, fully constrained the lines in the sketch to the PG from the lines in the standard view.
Everything looks good but when I click "Finish Sketch" and it leaves the sketch environment the lines from the sketch shift slightly out of alignment.
The dimensions I have to these lines are in the right locations so it looks like they aren't going to the sketch lines. But if I try to "connect" the dimensions to where the lines are actually being show it gives me errors saying there is nothing there to connect to.
Using Inv 2013 and VB 2010. I am trying to reference a sketch within a drawing view, but I am having a hard time figuring out which view number and sketch number to use. I thought I had it figured out, but apparently I was wrong.
For example, see the 2 attached pics, Drawing A and Drawing B. For Drawing A I had the sketch reference set as
Dim oSheet1_View As DrawingView = oDrawDoc.Sheets(1).DrawingViews(3) Dim oSketch As DrawingSketch oSketch = oSheet1_View.Sketches.Item(1)
Drawing View 3, as it was the 3rd Drawing View in the list, and Sketch #1 within that Drawing View. I thought this was how it worked, because it worked with my code and it hid the sketch. However, moving on to Drawing B, I used the same code, and it does not reference that sketch at all. It did nothing to it. Even though the Flange_Holes sketch is in the same position. 3rd View down the list, 1st sketch.
So how does Inventor reference these views and sketches? Is it in order of creation? Is there a way to reference it by the what the sketch is named instead of trying to decipher the number it's assigned? I have a lot of drawings already made, and I'm not positive the views were taken and created in the same exact order each time.
Is there any way to stop the flipping of the solid/sketch view from iso to normal?
its annoying to make changes to a sketch and constantly have to re orient the part after finishing a sketch, I dont want the solid model to return to iso view after sketching, is there a setting for this?
I can "Get Model Sketch" to make it appear visible in a drawing view. But I can find no way to use these "edges" or "lines" or "entities" or whatever they are, later in a drawing view sketch. No way to project them from Model Sketch to Drawing View sketch. I can attach leaders and dimensions to these Model Sketch entitites but I can find no way to use them in a sketch owned by the drawing view. Am I missing something?
I have just upgraded to 2013, and there is one "feature" I find kind of distracting. When working in a part, I create a new sketch. When I extrude that sketch, Inventor automatically switches me to an Iso view. I don't want that. I would prefer to stay in the view that I established.
I have a VB program that auto updates the size of a door and frame assembly, and in turn, updates the shop drawings to reflect this change. I have a view on my shop drawing that I have drawn a sketch in. I start the sketch, add my dimensions, and I use 'Project Geometry' to project the edges of the actual part around the sketch to constrain my sketch and keep it in place. The problem is, as the program runs, and the door/frame changes height, the sketch loses it's dimensional references to the projected geometry. When I go back and reopen the drawing after running the program, all the dimensions that went to the projected geometry are gone.
Is there another way to anchor a sketch to a drawing view part instead of dimensioning to projected geometries? This doesn't seem to be working, and I've tried it every which way I can think of. Oddly enough, I have another sketch in a different view that is set up the same way, and it never misses a beat.
I use the same sketch to create a break out view in one type of drawing. I may be blind, but I can't seem to find a way to save that sketch and reuse it when I want to create a break out view.
If I zoom in on a small detail in a large sketch and then issue the "edit sketch" command Inventor changes the view to where the origin is visible on the screen. Is it possible to disable this?
I'm using Inventor 2012, and experiencing some trouble with certain types of projected geometry that I'm using in a sketch associated with a view in an .IDW file - but only when the view involves a break (or breaks).
I'm generating section views to show the layout of hole details at various axial locations along the part. When placing a section line, I can't "pick up" any appropriate locating geometry from the view. So, after creating the view (using just a vertical section line), I edit the sketch that defines the section line. Project some geometry (the edges of the holes, in the attached example), draw some additional geometry constrained to that, then constrain the section line to that. That works fine; if I move the view around, the section lines stay attached to it. This is what is shown in the attached "before break" picture.
When I apply a break to the drawing, though, the section lines don't follow the changing view. They stay right there, as if the view had not been broken at all. This is what's shown in the attached "after break" picture. Move the view around, and they track with it - but always staying the same "real" distance apart from each other. It is as if that projected geometry were completely ignoring the break.
I observe something similar if I start with an IDW view with one or more breaks, then create a sketch associated with the view. If I project geometry, some of it projects where it should, but other geometry projects elsewhere on the page - as if no breaks were present in the view.
The part I've shown here is something I put together as a simplified example of what I'm observing. The part I'm actually trying to detail is more complicated (many more details), and much longer (so breaks are a requirement to put it on paper).
Any time I click on "Create 2D sketch" when editing a part in place in an assembly, the view moves to an isometric view. It happens as soon as I click on the button. Is there any way to stop this happening?
This does not happen when I'm editing a part (.ipt) on its own. I'm aware of the "Look at sketch plane on sketch creation" issue: this is not the same thing since it happens as soon as I click on the button, i.e. before I actually create the sketch.
I want the view to remain as it was before I click the button, to keep the things I'm looking at in view.
I just installed a student version of Inventor Pro on my comptuer. I have used this and several other similar software packages before. My problem: when I open a new part file, it takes me to a gray screen. No coordinate axes, view cube, nothing. When I click "Create 2D Sketch," still nothing. Same gray screen. If I draw a line, it doesn't show anything.
I've gone to View -> Object Visibility, and everything seems to be checked off as it should be. I've also clicked User Interface, and it shows the View Cube among other things as being selected.
The software didn't prompt me for an activation key, not sure if that may be relevant to the problem?
I've created a shared sketch and have used it with various features. Sometime those features are suppressed. The model works fine but the shared sketch generates a sketch doctor error because the feature that created it has been suppressed. Is there anyway to make the sketch suppressed so it doesn't trigger a sketch doctor error? Inventor 2013
How do I duplicate the 2D line work from a part level sketch into a drawing level (overlay) sketch?
I started a simple 2D piping system diagram sketch by opening a new part file and using a sketch to stick draw the system schematic including some annotations. Then I opened a new drawing file and made a base view of the part file to bring a view of the original sketch into the drawing.
I realize now that it would have been much easier to have created the schematic directly in a 2D sketch at the drawing level, which would have made editing the annotations much easier at the drawing level, and there is really no need for the part file to exist. I have no intention of creating a 3D model or "real" part in the .ipt file, was just using it as a jumping off point to sketch.
I was thinking that I could correct my error in judgment by just copying the sketch and pasting it into a new sketch on the drawing, but it doesn't want to work that way. I have tried copying both the whole sketch at the browser level, and the entire sketch contents (all of the lines and annotations) from the opened part sketch, but when I attempt to paste either of those into the drawing, paste does not seem to be an option. I'd rather not have to draw the whole thing again, as in typical fashion, my once simple sketch has grown in proportion and complexity from its simple beginning.
I'm having trouble with constaints, I'd like to constrain my sketch to a point in another sketch on a different plane. Is this posible in Inventor? If so how? If Inventor works differently how would you get a points in one sketch to be linked to points another?
