The bug giving incorrect lenths of frames created on internal cutouts with fillets using merge hasnt been fixed in 2011 SP2 (64bit). Base part attached for testing.
Any chance of a hotfix?
I am creating an assembly where I need to add a light probe that is length X from a sensor to an LED. I would like to create a cable modeling this transition to make sure it can be routed around other components. I can't seem to find how to lock the length for the cable from point A to point B, it only changes based on what points I add on its path.
View 1 Replies View RelatedI just missing something or is there no way to get frame generator parts to list their lengths in feet?
I have authored some structurial parts and everything was done in feet, when I insert them directly from the Content Center, everything work like I want it to, but when I use frame generator they lengths are always in inches.
I know I can change it in the BOM but I'm trying to make it more consistant for everybody.
Inventor Pro 2013 (PDS Ultimate)
Vault Pro 2013
Windows 7 64
Xeon 2.4 Ghz 12GB
The frame generator gives the wrong cut length (G_L) when using double end treatment "Trim and Extend to Face"
See attached screen shot: The correct length of the diagonal RHS should be 1852 mm after trimming the RH end to btm and rh member. As far as I remember this is an old problem never been fixed. Is a lot of work manually altering the cut length of 20-30 member in the BOM.
If it is possible to set a fixed length to a "Hose" hanging from one point to another? So that when hang-off point's are adjusted (any direction) the hose act pursuant to the fixed length.
View 9 Replies View RelatedI have a feeling this goes way back to the first release of INV we had (release 14?). Basically the merged FG member length seems to be calculated using the member centre line instead of real lengths. See the attached Pack-N-Go.
The view on the left is a Merged FG member. The view in the middle is individual FG members based on a line of symmetry in the same sketch. Both are placed using the mid point option in the FG dialogue. The views on the right are the 3 separate members used for the middle view.
The Merged length shows 722 mm whereas adding the 3 member lengths (RH view) equals 740 mm. 18 mm short, or 2 sets of 9 mm (shown in the middle view) which represents the end cuts to the middle member in the RH view.
Windows 7 x64 -64 GB Ram, Intel Xeon E5-1620 @ 3.6 GHz
ATI FirePro V7800 2 GB, 180 GB SSD & 1 TB HDD, Inv R2013 PDS Premium SP2 Update 3 (Build 200), Vault 2013 Workgroup Update 2 (Build 17.2.9.0)
I have an OS plan with the 100 metres squares marked.I want the ruler to coincide with the known 100m length.Then I can mark on layers various lines of say 7m or 25m long.How can I set the ruler and guides to enable me to draw lines such as this.
View 9 Replies View RelatedAfter using Custom Profile for Frame Generator, the Part List will show total length, not individually. How to split these frame members?
View 2 Replies View RelatedI created an extruded aluminium profile (attached file: Item Profile 8 80x80) which I published into the Content Center. When using this profile in a frame design, and using the Trim To Frame command, the profiles are trimmed at a weird angle (attached pdf file).
View 2 Replies View RelatedAfter using Custom Profile for Frame Generator, the Part List will show total length, not individually. how to split these frame members?
Inventor Professional 2013 SP1.1
Windows 7 Pro 64-bit, SP1
HP EliteBook 8460w; 8 GB RAM; i7 - 2.0 GHz; AMD Firepro M3900 -1 GB
There should be a way to Notch a straight frame to a curved frame! I want to laser cut the tube, so I really need to trim one tube to a curve tube.
View 8 Replies View RelatedI come across this problem from time to time and generally either just ignore it, if the detail is destined for in house manufacture, or alter it in autocad if it's destined for exterior suppliers.
Our guard frames are manufactured from extruded aluminum section (made by a company called palletti) I have when needed created a new frame generator frame member for each new x-section that we wish to use. I then draw a 2d sketch for the base frame skeleton and then a 3d sketch for all the frame work above. This I then use in an assembly to create the framework. This framework assembly then goes into a second assembly where the framework is then adorned with all the accoutrements that make up a guard frame that we can then order as an assembled frame, panels feet, hinges et al.
When placing the views for the detailing of the second assembly sometimes the view will show the wrong length for one or some of the frame members.
;note how the left and right views are different and how some of the frame members are elongated on the lh view.
I'm guessing its because of the home grown frame members but all seems to work well other wise and this only happens infrequently.
HP z210 16Gb ATI FirePro5800
Autodesk Produst design Suite 2012
Why can I not constrain placed objects with three constraints? Anything I place constrains with one constraint then is virtually fixed (without being) and cannot even be moved to allow for further constraining.
View 9 Replies View RelatedI created a sketch on a 'fixed workplane' and extruded it. I would like to know if it is possible to move the workplane? I understand I can change the workplane if it is a 'plane by offset from plane'.
If moving a fixed workplane is possible, does the extruded features move along together?
How does Inventor "Remove fix constraints" so quickly? Can this be replicated in iLogic?
The way I've previously done this requires looping through the constraint collection and deleting one at a time which may take a few minutes on a complex sketch, but when Inventor deletes fixed constraints throught the menu option it does it in a few seconds on the same sketch so Inventor must be able to select them all at once and delete them all at once. Is there a way to do this through the API or iLogic?
FEA of a hollow metal ball.
The case is-
1. hollow steel metal ball OD 200mm, ID 190mm
2. Outside surrounding uniform pressure 10 MPa.
3. The ball is floating in a kind of liquid, so the gravity is neglected.
How to run FEA on this ball? How to add fixed constraints.
I've come across this many times now. When in an assembly, I create a sketch. I then try to project geometry and I will sometimes get this error:
"Cannot constrain or dimension reference or fixed geometry."
why I can't project edges/faces/points of certain parts?
The fixed width function did not work when I wanted to draw a fixed width rectangle. Is there a new way to do this in CS6?
View 4 Replies View RelatedI'm sure this has been asked many times but none of the queries I used brought up a similar question. My issue is that I recently spent a lot of time annotating a detail view with leaders attached to geometry, leaders not attached to geometry, and sketches constrained to geometry projected from the view.
I made some modifications to the model which didn't re-locate any of the components that I'd annotated, but somehow the detail view got shifted, and all of my leaders are pointing to the wrong place and the parts of my sketch that weren't constrained to geometry are in the wrong place as well. Some of the leaders seem to have held to their posts better than others, but for the most part my annotations are worthless and will need to be re-done.
Is it possible to change the length of a line based on the length of an attribute?
I'd like to make the line a MINIMUM length of X" (I haven't decided how long yet--but know I'll need a minimum). But then after the user fills in the attribute, I'd like the length of the line to change to the length of the attribute plus a small amount (again, I haven't decided yet how much extra).
I was wondering if there is a way with DB's to have a line "follow" or "grow" with the content/value length of an attribute. Maybe some method of linking the attribute width to length of the line? Essentially, it would work just like turning on the underline setting when typing in mtext editor (or any program with an underline option for that matter), expect that the line could be placed anywhere, and would not have to reside directly below the text.
View 5 Replies View RelatedCommand to make a line change length to match length of a line, arc, polyline or circle? Could use this when making flat patterns layouts.
View 5 Replies View RelatedWith using superelevation wizard in Civil 3d 2012, changing the lane width is not affecting the resulted values of transion length and run-off length, Is that correct ? ( as civil is using standerd AASHTO tables which assume that lane width typically is 3.6m )
Also, There is only 2 tables for 2-lanes and 4-lanes roadway, Is it for total road width or for one directon only, and what about different no. of lanes ?
I am creating a block with attributes for a standard job. I have (4) total attributes in this block (for example: panel type, qty, length in imperial, length in mertic)
I would like my length in metric attribute to automatically populate based on the input from length in imperial.
Is this possible?
I'm modeling cables running through a series of cable clamps. I'm working in an assembly with my structure as one part, clamps as seperate parts, and cables as separate parts. I modeled the clamps first and am using them to create my 3d spline to run the sweep. The clamps have moved several times and each time, the sweeps (cables) do not update to follow the new clamping path. I have tried multiple ways of solving this.
I've tried to redo the splines using "Include Geometry" and running the spline through the centers of the clamps. I've also deleted the constraints (which for some reason turn into fixed) and reapplied them as coincident constraints. However, once I setup these coincidences, they always change back to fixed.
In a last ditch method, I've created 2d sketches at EVERY clamping location (yes that's alot of sketches, time and effort) and projected the circular geometry to get a center point. This has seemed to work, but is so much work, there's no way we could use it regularly.
we are doing a customization of part in inventor , where we have done fork plate with constraints in model and extruding it with inputs from excel sheet. the plate size is getting changed as per the input given excel sheet.
but during the 2d drawing generation, if i take bom - the length and width columns are not coming.
I'm making a tube that is connected on another tube. I did this by skeleton modeling, for my tube extrusion i used Extrude To surface.
Is there any way to get the length of that extrude?
I know its possible to get the sweep length like this. Is there a way to get the extrude length as well?
'Set a reference to the active part document
Dim oDoc As PartDocument oDoc = ThisApplication.ActiveDocument
Dim oDef As PartComponentDefinition oDef = oDoc.ComponentDefinition
Dim opath As Path opath = oDef.Features.SweepFeatures.Item("TheSweep").Path
Dim TotalLength As Double TotalLength = 0
[Code]....
In authoring fasteners, what Grip Length refers to?
View 2 Replies View RelatedI would like to dimension the arc length of a radius in sketch mode. I am using Inventor simulation 2010.
View 4 Replies View RelatedI have a drawing where it is difficult to get length, weight, or cut out of an ipt.
Or how do you get it straight up for a presentation drawing?
(you can see the image in test1.bmp (our see the part in test1.ipt
I am trying to dimension a line that is not parallel to either they x or y axis. When i try to dimension the line it will only let me dimension the vertical or horizontal component and not the diagonal length. I have included a picture of what I am referring to.
View 5 Replies View Related