In Solidworks I can emboss a sketch into a 'wavy' surface without difficulty.
If I try to do the same thing with Inventors 'Emboss' command It fails with "Only planar, cylindrical or conical faces are supported."
Surely there must be a way to achieve the same effect as in the first illustration, in Inventor ? Am I missing something obvious?
I've attached the file (Inventor 2013). The sketch shown is a raised lip I'd like to have around a future opening. I actually want that sketch to wrap all the way around the body, but taper down to 0 in the rear as there are to be hinge plates. This is going to be a grill/smoker and there needs to be a 3/8" raised lip at the future seam of the top and bottom. Shown in the model is just the top portion.
View 8 Replies View RelatedIs there any way / trick to wrap a 2D sketch to a non-flat/cylindrical/conical face? See attached part. I'd like wrap the lines in Sketch2 to the ring's outer face in order to get a proper path for "engraving". I see no other way to get a proper path for sweep, because project along vector won't work.
View 2 Replies View RelatedI'm trying to build an assembly with conical rollers rolling on a cylindrical support. Refer to the attached sketch. I'd like to be able to constrain the conical faces of the roller to the cylindrical surface of the support. It doesn't seem to be possible to do that in Inventor; or, more accurately, it's not possible to put a tangential constraint on both conical faces at the same time. The first tangential constraint causes the part to place a generatrix line parallel to the axis of the cylinder. (I had to look up what generatrix means, too.) So it's not possible to make the second tangential constraint.
How I can do this? Just in case that's not difficult enough, the reason I'm doing this is because, ultimately, the support will not be a plain cylinder but actually a tube that also curves. It's the behaviour of the roller through various curves on the support tube that I ultimately want to model, but I have no hope of doing that if I can't even get the roller constrained onto a plain cylinder.
I want to find the intersection point between a cylindrical curve and faces in a body. I have the start point an start vector and a rotational velocity. With this values it should be possible to create this cylindrical curve.
Is there a function in inventor which I can use?
Currently I am using the function "FindUsingRay". But I thing that there is only the possibility to fire a linear function through the body.
Today I found the command "FindUsingVector":
Sub FindUsingVector(OriginPoint As Point, Direction As UnitVector, ObjectTypes As SelectionFilterEnum(), ByRef UseCylinder As [defaultvalue(-1)] Boolean, ByRef ProximityTolerance As [optional] VARIANT, ByRef VisibleObjectsOnly As [defaultvalue(-1)] Boolean, ByRef LocationPoints As [optional] VARIANT,
I did not find any information in the "Autodesk Programming help". what is the difference between this both functions?
Is the argument "UseCylinder" for a switch into cylindrical coordinate system?
I am Using Mental ray (max 2010). I have made a topological displacement map at a very low resolution. it is 222 pixels wide by 111 pixels tall (landscape) It is greyscale and low rez because the mesh I am applying it to is 222 faces wide by 111 faces long. (landscape also). I did this because I needed each pixel to become a "height map" in its own right. Everything is working the way i expected.
My problem is.... I need to now make each face z planar. as it stands, they are all tilted in the direction of the grey scale falloff. I have tried splitting the edges of all the faces (quad) and using the make planar (z) function of edit poly mod. No matter how I set the pivot / ucs, when I apply the make planar z , they all average out to the same z plane. I need them to adopt the average of their individual z planes. I can do this but have to do it face by face. That's 24642 faces.
i got Inventor recently, and i've been working on a model of a longboard just to teach myself how to use the tools in Inventor. right now i'm trying to color areas for the griptape pattern so i drew the 2D pattern and projected it onto the 3D model of the longboard. but when i tried to split the faces of the model along the projected pattern only a few of the projected lines split the faces. for other faces i kept getting these errors:
Create parting line failed Crane.ipt: Errors occurred during update Split11: Could not build this Split The attempted operation did not produce a meaningful result. Try with different inputs.
Is there a way to print planar surface of any model in inventor 2012? I know that autocad is able to print planar surface, but inventor is much better to use.
View 9 Replies View RelatedI am not sure what I am doing wrong but when I use the bend tool I am getting weird results. Does the surface to be bent have to be planar? See photo attachment.
View 4 Replies View RelatedI am creating a fan wheel (see attached). The fan blade needs to be extruded to the inside surface of a 2 piece cone assembly. To make it even more difficult, the inner portion of the blade needs to be cut at an angle so that the extrusion ends at the cones. See attached pdf reference sketch. The result for the flat pattern blade edge should be two parabolic curves.
View 9 Replies View RelatedI have cut out a spiral from top on a cylinder, now I want to make a nice finish. And cutting with a conical spring profile is the way to do it.
View 5 Replies View RelatedI created a part that spans between two other pieces. The original part model does not have a twist in the "flat" surfaces, so it unfolds just fine, but it also does not represent the way the actual part fits, so it is difficult to determine if any other parts are fitting correctly up to it.
I had a problem getting a part to unfold before, and I was shown a method of creating a surface body and a thicken, which I have done with this part, but as of yet have had no success unfolding this part.
Is there anything that I can do since the sides are twisted and not planar?
I need a conical spring that can change in pitch as it tapers. Basically the spring starts in a compression style and tapers down to an expasion style. The CNC spring machines are capable to produce it, but am I able to, through Inventor? If not when will we have this feature capability?
View 7 Replies View RelatedI have the German version of Inventor 2014, so some translations may be different.
I want to project a text on a sketch onto a conical surface. The error message is that the chosen surface wasn't tangential to the profile plane. I found no way to rotate the plane.
How do I project my profile onto the conical surface or How do I make the profile plane tangential to the conical surface?
I am drawing a fan wheel. The fan blade is curved intersects the shroud, consisting of two cones. I do not know how to trim the blade to the cones. I tried to "split" the blade at the cones and then "delete face" but then the "Go to flat pattern" section on the ribbon is missing. If I suppress the "delete face" feature the "Go to flat pattern" re-appears.
View 1 Replies View RelatedIs it possible to create a transition when the backplate shown in the picture is a cylinder?
I have tried several options, with 3Dpaths both nothing worked so far.
Inventor 2014 sp1 | Vault basic 2014 | HP Elitebook 8670W | win7 64b | 8Gb | GMT +1
I need to model up a length of rod with a cylindrical end with a hole in it. The cylindrical end needs to be flattened slightly where the rod meets it. How to do this ? See attached picture.
Autodesk Inventor Professional 2013 SP2 64-Bit Edition
Windows 7 HP Z400, Intel Xeon W3550 3.07GHz
12.0GB RAM, ATI FirePro V4800 (FireGL)
i drew a cylindrical cam using the inventor tool then i also drew the actuator ( a simply plate rounded on top) but when i add the contact tangency link between the two surfaces and i move the cam , the two objects interpenetrate!
i'm using inventor professional 2012
I need to drawing something similar to the attached image on either side of a "U" shaped rod.
The "U" shape is drawn using a sweep of a circle (the hatched section on the atatched image illustrates).
I just can't fathom how to draw the solid at the top oneiter side.
I've been trying to add a plane at an angle, then draw a circle & try to sweep that for each half of the "u", but after a few hours, total fail
On the module generating inventor springs 2012 can generate a conical spring?
View 9 Replies View RelatedHow can i get the length or diameter of a cylindrical face by selecting the face as shown in the attached picture.
View 4 Replies View RelatedIs it possible to show the deformed nature of a shaft after loading along its axis and simulation of the part. If you take as an example a rod of Plasticine and stretch it you will see the center section thinning,the same laws apply to a rod of steel during stretching,why is it that this is not shown during the
simulation of the part,is it mesh settings or something that is not built into the analysis. When one applies loadings to sheet metal the deformation is clearly shown.
I need to draw a cylindrical cam in Inventor Professional 2013. I tried using the cam module but it is not what I need. My cam can be generated by a third-degree polynomial. You could use the new "curve from equation"?
View 1 Replies View RelatedI'm trying to constrain the green cylinder to move between the red frame. The red cylinder is constrained on the surface of the larger gray cylinder, which moves around the grounded red frame. When the green cylinder goes up hill/down hill the larger gray cylinder is supposed to rotate around its own axis.
When I choose transitional constraint I'm only able to pick one face on the red frame, and not the whole face. I think it's because the face is not planar, but varies in z-led.
Neither am I able to use the Contact Solver, it seems like the friction is too high. The green cylinder doesn't slide that well when using Contact Solver.
I am really struggling in trying to revolve around cylindrical body on a specified angle. I understand the degrees of rotation angle, but i am looking to revolve or extrude a certain shape for the length of the shaft. Like trying to make a coil or a set of threads.
I have tried to use sweep but sweep doesn't work with two sweep lines.
I have just created a cylindrical object with an extrusion length of 300 mm and then created an assy(.iam). On to this cylinder i have placed a plate at right angles to the axis of the cylinder
What i wish to do now is mirror this plate.
It would appear the best way would be to create a work plane(mirror plane) thro the centre
Of the cylinder,however, how can this be done if when requested to create the plane 3 points are required,am i missing something here.
I'm currently detailing a part that's about one-third of a cylindrical piece (the part is lathed as a whole and cut into thirds). I'm trying to project the centerline onto the section view so I can ordinate dimension to it.
View 3 Replies View RelatedI have 2 separate sketches which will be used to EMBOSS on the curved surface.I can get them to work except i want 1 sketch to be Green when Embossed on the surface in color and the other sketch to be red in color when Embossed with the back ground Black.I can only get it to work as 1 color.I tried with Split command but still no luck.After both sketches EMBOSSED to the surface i can only get 1 color for both EMBOSS
View 1 Replies View RelatedIs there a way I can use the emboss feature in an assembly? We typically laser mark during final assembly and would like to show that as a step in the assembly instructions.
I typically create a sketch with the text and extrude(cut) in the assembly. It works fine for flat surfaces, but cannot do it for other surfaces.
The one way I can think of doing it would be creating ipart with text and using it in the assembly. I would rather not do it this way. Is there any other way to accomplish this with out altering the components (.ipt)?
In a part, I create a sketch, add annotation Type in the file name. Then create an Emboss feature using this sketch.
How can I add the file name property to the text. I want the the emboss to update to new file name if I rename the file.
How to emboss scale on the cylinder? Please see the file attached. The arrow is the portion I want to created in my part file.
View 9 Replies View Related
