I would like to measure the distance in assembly.
The distance is between two hole axis.
I use Measure Distance tool.
I do not have the “Select Other” option to choose axis supposedly pop up ofter the preset delay time. Seems like Application Option – General – Selection is responsible for that?
But it is checked to ON as on pic attached. My laptop machine works fine with the same settings.
Is there a way to get the dual unit option to read in both feet and inches....for instance 32.75 to read 2'-8 3/4" instead of 2.729 ft?
View 3 Replies View RelatedI have a VBA form coded that we use to generate part numbers and descriptions that then populate the iProperties. We often use the part sizes in the description. I would like to be able to put a button on the form that allows users to use the "Measure Distance" tool so that they can measure the part while they are creating the description.
Any code that I could use to activate the "measure" tool while a vba form is active?
in 3D - Section Box all measurement tools are grey indication of no use/doesn't applay/stay away/? Using 3D-SB you can have a glance insidea 3D modell and there be objects that only have a elevaton and no other properties except New Constuction (Specialty Equipment). So confirming space is a pain.
View 6 Replies View RelatedI'm just playing with a rotor head of a model helicopter (see picture). For proper initial alignment, all main parts shall be setup parallel against one-another. This can be done by aligning the length of the ball linkages.
But therefore I need to know the distance of the ball centers. How can I do that? (STEP file for testing with different Inventor versions is attached).
I want to add the Measure (Distance) command to my quick access toolbar. When I right click on the Measure button the "Add to quick access toolbar" is grayed out in 2013.
Also why can't they make it so when I add something to the quick access toolbar stays added to all file types. I have to add it to .ipt, .iam, .dwg...
BTW Not real impressed with 2013 so far.
Using Inventor 2013
I need the perpendicular distance between 2 polylines. If I was doing this manually, I would draw a line perp from 1 side and extend it to the other side, check it's length, and delete it. These are pipeline r/w's that quite often have variable width, and are not always parallel.
I am asking the user to select the pline 1st (GetEntity) to get some object data. Then I prompt for a point on the pline where a block will be placed. The block contains an attribute definition for the width. I check to make sure the point is on the pline. I was hoping I could get the user to select a point on the opposite side and force that to be perp. That would give me the width but it doesn't work. I have looked at GetFirstDerivative and rotate that 90 but the examples I found use a certain length. The perp length is what I need to determine.
When I use the measure distance command, I have to exit out of the command before I move on to my next command. I'm used to measuring once and the command automatically exits (in previuos releases). Is there a variable that will exit the command after one measurement?
View 4 Replies View RelatedWhenever we use measure tool it will show the a dialog box with valves of x,y,z, delta X, delta Y & delta Z. I want to customize the same as per the attached image.
Customize this, dialog box will not disappear(modal) after entering into any other command so no need to remember the values of x,y....etc.
Is there any way of displaying the geodetic distance(ie "mapdist") with the dimension tool instead of the normal distance?
View 2 Replies View RelatedCan we use measure tool without having to open the part file?
Say directly in the viewer or in vault viewer.
C1
Inventor Professional 2013
Vault Collaboration 2013
I reset Photoshop's preferences and the specific tool and all tools twice to no effect. Shift works fine to select for a perfect circle or rectangle the option tool is just not working to select from the center.
View 3 Replies View RelatedHow to keep a section view of an iam active when accessing the distance tool? As soon as I click on the distance tool, the half-section disappears. This makes it difficult to measure relationships from one component to another. I am using Inventor 2013 which was recently installed on our workstations.
View 3 Replies View RelatedIm trying to show some measurements in layout view. But when i dimension between 2 points i get the number 71,84. When i use the measure tool in model view i get 1150mm which is the correct length.
Sure there is some simple reason why the two arnt coming in with the same value. Also it isnt an issue with Units as i have checked both and they are both in millimetres.
I trying in max 2012 to select some object(object count 600)by select from sence option but this selection process is taking long time.
View 2 Replies View RelatedFound that in certain drawings, the measure area tool will just suddenly stop working? It's very odd. It let's me pick points, but won't let me press enter to see the total.
Closing and reopening AutoCAD doesn't work. It seems to be a permanent thing to the affected drawing.
It's happened to me in a few drawings, but only in those specific ones. Other drawings are fine. I'm guessing it's a setting I've changed somehow?
I've been getting round it by creating shapes using the polyline, and then looking at the area in the properties window. It's an ok solution, but not ideal.
I have a big problem with the viewport in 3ds max 2011/2012. On each viewport I have a black or white bars on right. these bar make the mouse become inaccurate for example when i want to select a vertex I can't drag the mouse on it and click. I have to move the mouse away from it a distance to select it (see my attachment image). I tried to update the graphic driver and the 3ds max 2012 SP1 but the problem's still there.
View 9 Replies View RelatedMeasure Tool Not Displaying Results In Autocad 2013 Mac
View 4 Replies View RelatedThe measure tool is not giving me the correct measurement. For example, I offset a line 24' and when I go to double check the distance it is off by .03. That is starting on the original line and doing a perpendicular snap to the other line. So I thought, wait a minute that can't be right, so I drew a line between the two lines and did an inquiry and it gave me 24'.
I also did a dimension which also was correct. I also measured a 97' line and it was off by 3 feet. Never had issues with previous versions of Autocad as far as measuring.
I've figured some things out, but am struggling with what appears to be a very valuable tool... the area tool.
I found many references to the boundary tool, but that looks more complicated.
I have figured out how to mark the corner and press enter, but the output is for example 1.7 sq ft vs. what should be approx 35K sq ft.
I tried to change the units, but that didn't seem to make a difference.
is it possible to measure the distance between two lines but is it possible to set the scale (calibrate) to customize the dimensions. For example, we have pictures with a ruler in them and we need to set the scale in PS to equal the scale on the ruler.
View 6 Replies View RelatedIn CS, I observed and confirmed with other users the following behavior:
1. Use Measure Tool to establish horizon
2. Image > Rotate > Arbitrary
3. Image > Adjust > Levels
At this point, Measure Tool reverts to Eyedropper Tool. For my workflow, this is lots of extra clicking. Would someone please check this in CS4 and see if the Measure Tool stays as Measure Tool?
Software: GIMP 2.8 part of Ubuntu software (13.04 - 64 bit)
I am unable to use the measure tool. When I use it, the distances and angles keep adding to the last reading and these cumulated readings are of no use.
How to start a fresh set of measurements within the same session?
This is most likely a stupid question but it has had me stumped for a while... Every time I close an image the eyedropper tool pops back to the top. What do I have to do to keep the measure tool on top?
View 1 Replies View RelatedI'm trying to draw a plan of my house in Autocad 2009 but I seem to be endlessly using trim and extend because I can't easily select the points that I want with osnap. Eg. imagine I have a box, and I want to start drawing another box inside it that has each side as 10 units smaller than the corresponding side on the outer box.
Step 1 - I draw a small line from the top left corner of the big box using the endpoint snap, typing in "5" for the length.
Step 2 - I then do the same at right angles to the first line to get me to the starting point of the inner box. This always leaves me with 2 small lines to remember to delete.
Step 3 - Then in order to draw the top line of the inner box I end up drawing to a random length because I can't say "draw until 5 units away from the right hand side of the big box", then I end up trimming it later once I've repeated steps 1,2 and 3 for the next side of the inner box.
I know in my example above I could have scaled the box down or something but that's not what I'm getting at. I really want a way of selecting line start and end points that are a known position away from an existing point.
I know we all love the measure tool, but if you want to stroke with it what you are measuring in a certain angle you can't do it. At least nothing that I know of. How do you trace your angles with measurement (whether degrees or radians)?
View 2 Replies View RelatedWhen I click the select tool, a brown selection type of rectangle appears in a particular area of the illustration, even though I have not clicked on the illustration yet. I assume it is some type of warning indication, but don't know what. P.S. It is draggable and scaleable - I can move it off the artboard. An example:
View 5 Replies View RelatedI know this discussion title is a bit murky, but the problem is a bit odd. I have Photoshop CS6 v13.1.2. In this version, I will activate the Select Tool, check Auto-Select: Layer, check Show Transform Controls, and then while using the Select Tool I will drag to create a rectangle to select multiple layers with content within the specified area.
Unfortunately, this action only works when I begin the selection from outside of the canvas area. If started from within the canvas area, no rectangle will appear, it will show me a measurement of my selection size, and then no layers will be selected upon release.
This cannot be working as intended right? I mean multi-select dragging cannot be intended to only work when started outside of the canvas right? Is there some way to fix this issue? Is this a bug? See the images below for more information on this issue.
I am trying to oTrack distance from the top circle edge of a cylinder to a certain distance ... whenever i try to do that ... it either track to x and y .. but not in z :/ ... the video i have on you tube he did it so simply and it seems to be easy .
I am not sure what is wrong .. but i heard parallel and perspective view could make a difference .. i actually try both :/ ...
[URL].....
I remember being able to select anything on the canvas with my Quick Select tool in CS5.5 Photoshop Extended. Recently, making the switch to CC, the Quick Select tool will show my slection as I drag along the canvas, but once I release the mouse, the selection seems to be reduced to the visible pixels. I was intentionally trying to fill the transparent sections with my effects as well.
Mind you, the magic wand will select transparent pixels just fine, but it also adds unintentional sections which is irritating. I should probably also pint out that I already looked into the "lock transparence" option in the layers, but I did not activate anything of the sort.
Can the image be saved with the annotations of the measure tool in PS Extended?
View 1 Replies View Related