I have an assembly of parts that are on a stand thathas four (4) legs. If you were to distribute the load from CoG there will be vertical forces as well as moments on each pad that will support this assembly. Is there a way for Inventor to show the distribution of the CoG load on the given points?
View 1 RepliesI have an assembly that i need to know the mass of, easy enough, however the assembly needs to be weighed without some of the parts in it. I hought i could simply uncheck "enabled" of the unwanted parts and re check the mass, however it does not change. Any solution besides adding the wanted parts individually?
View 6 Replies View RelatedHow I can get my parts list to show a total weight? Obviously, getting the weight of each part into the parts list is easy. However, I have not been able to find a way to automatically get a total weight for the entire assembly.
View 5 Replies View RelatedI need to have a sub-assembly (named ass1) with two different BOM structure: one should be normal and the other should be phantom.
The normal one I need to use it in main assembly (named assy2). In the drawing of assy2 I need to show the assy1 in the Part List.
The phantom one I need to show in another assembly (named assy3). In the drawing of assy 3 I need to show the components of assy1, not the assembly.
I have a wall of frames, if you will, and some frames within this wall are different sizes. When doing the BOM, I want to be able to combine anything that has the same stock number as well as the same cut length. The only way I have thought to do this so far is to cycle through each stock number and if the cut length is the same, I override the quantity of one and change the BOM Structure of the other to "Reference".
How can I change the BOM Structure to reference without selecting the part or going through the BOM Editor? Is there some VBA code I could utilize? I am striking out by solely using iLogic.
The weight of the parts is correct but if the quantity is greater than 1 in a weldment the BOM collumm does not do the math and multiply the quantity X the weight. If it is a formula what is the syntax?
View 1 Replies View RelatedIf I pattern a feature in two direction, say 1 copy in both directions, I get 4 features. Is there a way to "turn off" one or more of them. If I patterned a whole field of features, can I turn off some of them? Again, there was a way to do this easily in Pro-E, but I have not found it in Inventor.
View 2 Replies View RelatedSee attached,
My section lines "legs" are coming in very long in idw.
I unchecked "show entire line" and it still leaves a massive line away from the arrow.
We have a 3rd party developing some marketing drawings for us and they are using a font that does not come with AutoCAD OOTB. When we couldn't see the text because of this "unknown" font, they sent us zip file with all the "Gotham-*.otf" files to load on our computers. My concern is probably obvious, that any customer of ours who downloads these drawings from our website will have the same problem with missing fonts. I suppose they could use the substitute font but then we would have no control over what they see.
View 5 Replies View RelatedWe use C3D 2012 (metric only) - We are attempting to customize our list of structures for Sanitary Sewers. The structure list shows sizes we do not use and we would like to modify them. However, when we try to select the "Inner Diameter" it displays a list of sizes that we can not seem to modify or add to.
I have looked at some of the XML files to try and modify or add new sizes (example: AeccStructConcentricCylinder_Metric.xml) , but they do not seem to be recognized even after I restart the program.
Here is what the file looks like:
<ColumnConstList desc="Inner Structure Diameter" dataType="float" unit="mm" name="SID" id="CCL1" visible="1" context="StructInnerDiameter" index="0">
<Item id="i0">1200.0000</Item>
<Item id="i1">1350.0000</Item>
<Item id="i2">1500.0000</Item>
<Item id="i3">1800.0000</Item>
<Item id="i4">2050.0000</Item>
<Item id="i5">2300.0000</Item>
<Item id="i6">2550.0000</Item>
I tried modifying the last line replacing 2550 with 3600.
I also tried adding a line <Item id="i7">3600.0000</Item>
I saved the XML file and restarted the program with nothing changing that I can see.
Looking for correct file(s) to edit so I can modify the LISTS that come up in the piping modules.
One good thing about null structures is the way they display in 3D. They cover that gap in the pipe segments. Can I steal that shape?
I am currently using a simple cylinder for water pipe "joints" and turning it off like most people do I think.
Take a look at these two pipes and let me know why they each have a different mass when they can be overlayed and appear the same?
View 3 Replies View RelatedI have a drawing where it is difficult to get length, weight, or cut out of an ipt.
Or how do you get it straight up for a presentation drawing?
(you can see the image in test1.bmp (our see the part in test1.ipt
I have drawn a pipe network with multiple concentric sturctures. I need to make them all eccentric now. Is there an easy quick way to do this, or do I have to redraw all of them. When I go to the properties, I cannot find an option that allows me to change this.
View 2 Replies View Relatedwhy this difference in weight is appearing? Obviously i probably did something wrong. But what?
Inventor Version: 2014 SP1
Config : Intel (R) Xeon (R) CPU E5506 @ 2.13 GHz, 24 GB, 64bit win7
We have the weight inour title block tied to the mass property.It is set to populate automatically and it does very nicely.
The issue comes when I have an assembly and in the BOM I set certain components to be reference. When I go to Iproperties and then under the Physical tab select update,
the value updates there, but not in the associated drawing title block.
I am trying to include the weight for all components in assembly BOM as well as calculated overall weight in TB, but there are no available property to choose from in the drop-down list.
View 2 Replies View RelatedI would like to find the actual weight of a part in pounds.
I have attached one of the parts I would like to know the total pounds or ounces for. I’m using a specific material that I set in the Physical tab of iProperties.
Version = Inventor Pro 2009
I am using INV 2012 and I wan to to know a trick how to convert the weldment assembly back to regular assembly template.
View 1 Replies View RelatedI'm looking for the best way to create a separate assembly out of various component parts in an existing assembly so that the whole thing can be placed in an assembly as you would a part, I know it's possible to demote components within an assembly but are there any other methods similar / better ?
View 2 Replies View RelatedWe have an iLogic assembly with to parts in it. Maybe to cylindrical parts. The iLogic rules should do the following.
1. Start a Rule after open document.
2. This Rule starts a Rule in the first cylindrical component.
3. This Rule ask the user for a diameter.
4. The assembly gives this new parameter value to the second component
5. Then the assembly calls another rule in the second component to change it with the new parameter
Everything is working fine when the following combinations are taking place:
1. I open up the assembly out of vault or from a local drive or an accessible server drive
2. I insert the assembly as sub assembly in another assembly from a local drive or an accessible server drive
It don't work with the following situation:
- I insert the assembly as sub assembly in another assembly out of vault
Then the user becomes the dialog "Choose a diameter" twice.
I don't know why, but I have the idea it has something to do with the functionality of inventor to insert a component more than once. If you insert a component in an assembly Inventor gives you the opportunity to add more than one occurence after each other.
change that behaviour? Maybe a switch to change that inventor "add more than one occurence" behaviour.
I have encountered a problem with the Tube and Pipe styles.
As you can see, I have a rack assembly with a custom tube and pipe style. A wire as a tube in orange, and a tube support in white. Both have their seperate colorations at a style in the tube and pipe styles editor
When placing the rack assembly into the main assembly, it reverts to the coppor coloration I changed from the original style.
Steps I've taken:
Exported the styles .xml and Imported the styles into the master tubeandpipe.iam
Imported the user created .xml styles into the main assembly file nothing seems to work
I am trying to find the interior volume of an assembly (when am I not?!?!) by subtracting the assembly from a block that surrounds the most of it. Somewhere the assembly has a "leak" and I have been trying to use the Cross Section Analysis to track down where the inside lump is connected to the outside lump to be subtracted. Is there a less time consuming way to dynamically drag a plane across and get cross sectional views?
Even better is there a simple way to animate the analysis plane moving across the block so I can hopefully just watch and pause it when I find a leak?
Inventor 2013 (SP2 Update 2), Windows 7 Professional (64-bit), SP1, Intel Xeon 3.07GHz CPU, 12GB RAM, NVIDIA Quadro 2000, Vault Basic 2013
How do you make someone appear thinner or fatter in Photoshop.
View 9 Replies View Relatedit is possible to make a constraint that utilized a parameter of a part within the assembly.
For example, if I wanted to use the thickness of a plate, which I defined in the part, could I call that parameter in a constraint?
My assembly has grown (about 50 parts) to where I need to consolodate some parts into subassemblies for reuse and alternate iterations of the basic design.
When I import the original parts into a new assembly, all of the constrains I created are not there of course.
I've tried creating a new empty part and then deriving a new part from the assembly, but I can't add, delete or edit any parts.
I looked at using Shrinkwrap, Substitutes, iParts, Multi-body Parts, and Multiple Solids but I remain confused.
In retrospect, maybe I should have created the subassemblies between the part and assembly stage but I didn't.
I want to be able to control the location/position of a component in an assembly. This is easy enough through the iProperties/Occurrence tab and then adjust the location of the X,Y, and Z offsets. Is this possible using iLogic? I have been unable to find a function to access via iLogic. Ultimately I am trying to translate a component about an axis not a pattern.
View 1 Replies View RelatedWhen dimensioning views on idw my line weights disappear on the view I am dimensioning. The Display Line Weights check box stays checked during this.
The only way to get them to display correctly is to select a line in the view and right click select properties and hit OK.
System:
Inventor 2012 Professional SP1
Dell Precision 3500 Intel Xeon W3565 @ 3.20 GHz
12 GB Triple-Channel Memory
AMD/ATI FirePro V7900 2 GB video card
Is this possible? I have aluminum part and would like to know how much weight the thinnest area can handle.
View 3 Replies View RelatedOur Autocad parts lists used to calculate the weight of parts times the quantities. Now we are using Inventor and I see that the weight shown on a parts list is the weight of an individual part - although the quantity could be 2 , 3 (more than one). Is there a way to have the total weight shown equal to MASS times ITEM QTY?
View 1 Replies View Relatedi have an already edited part list (because there are parts that come from different assemblies and other ones that don't have to appear in that part list) and i like to show the total weight of my drawing, that doesn't correspond with any assembly.
So, there is any possibility of summing up the values of a part list column.