Can I use the spring generator to design a spring for me? I know my spring rate, my loads and my dimensions. I don't care how many active coils the spring has as long as it performs to the specifications I've calculated.
View 3 Replieshow to design and simulate a extension spring (not compression spring) in Autodesk Inventor 2012.
View 5 Replies View Relatedi have created compression spring under design and how can i simulate it under dynamic simulation? I cant create spring in dynamic simulation.
View 1 Replies View RelatedI'm given this data to generate my worm gear set with:
Worm Gear Data:
Diametral Pitch: 8
Number of Teeth: 27
Pressure Angle: 20 Degrees
Pitch Diameter: 4.219
Base Circle Diameter: 4.523
Circular Pitch: .491
Circular Thickness: .246
Root Diameter: 3.906
Face Width: .783
Worm Data:
Number of Threads: 5
Pressure Angle: 20 Degrees
Pitch Diameter: .938
Lead Right Hand: .375
Lead Angle: 169 Degrees
Addendum: .156
Whole Depth: .313
Chordal Thickness: .204
Inner Diameter: .619
Outer Diameter: 1.244
Center Distance: 5
My problem is it keeps changing data and/or failing. It particularly hates the 27 teeth (always changes it), never shows a 5.4 gear ratio (probably because it hates the 27 teeth), and won't accept an addendum of less than 1. Is this feature limited to only certain set gear setups? the automated tool won't accept these values (which I have to work with)?
When I try to create a pinned joint, I can't select the end plane for the vertical bar. Am I missing something? I've used this DA before, but it was quite some time ago and in IV2013.
Inventor 2014 64-bit SP1
Win 7 Pro 64-bit SP1
I have some problems with Bolt Connection Component Generator. For placement I choose Concentric, i choose all references, but I can't select Diameter. It is stuck to 10mm and i can't change it.
I am using Inventor Profesional 2013
We are having an issue when we replace a component in Inventor Pro 2012. When we replace a component, the name in the browser does not update to the new component. We've even tried to close and re-open the Inventor assembly and that does not work. We end up manual double clicking the name in the browser and type in the new component name.
Inventor Product Design Suite Ultimate 2012
Dell Precision T7500 Workstation
Xeon Processor
16 GB of RAM
Nvidia Quadro FX 5800
Windows 7 x64
II need a way to tell if a component occurence is a virtual component.
I'm using a For Each loop to cycle through all of the components in an assembly, and if the component is itself an assembly to set the LOD to "Custom". I'm using the definition document descriptor object for this. It all woks fine until the loop comes across a virtual component which doesn't have a definition document, so I need a way to check if the component is virtual and needs to be skipped.Here's the
Option ExplicitImports Inventor.LevelOfDetailEnumSub MainiLogicVb.UpdateWhenDone = TrueDim doc As AssemblyDocumentDim oLOD As LevelOfDetailRepresentationDim oAsmCompDef As ComponentDefinitionDim oComp As ComponentOccurrenceDim oComps As ComponentOccurrencesdoc = ThisDoc.DocumentIf.
[code]....
I am trying to make port rims for pipes that can be swapped in and out of an assembly. However, the ports will all be different sizes and located differently so I need the cut to be part of the port rim component, but affect the entire assembly it is part of. I've been trying to get this to work for the better part of a day now,Here's a picture of what im talking about. I'm running Inventor 2008 by the way.
View 2 Replies View RelatedHow do i get the spring to have a compressed look with flat end....i try different settings but not able to have the spring rings to touch for a compressed look.
View 8 Replies View RelatedI created a spring but when I try to assemble it with constraints it appears to lack a centerline.
View 7 Replies View RelatedI have to make a spring for an engineering class I have yet me nor the teacher know how to make a rectangular spring.
View 3 Replies View RelatedI can't make a spring moving according to other parts' behaviour. I use Inventor 12. by the way I sent two photos (scanned by Microsoft Security Essentials-no problem), the spring in the photos was made by design accelerators-as compression spring. I want from spring to move with the other parts but it doesn't. For instance when I pull the blue part down, blue part, and the spring go the into of each other.
View 3 Replies View RelatedI have cut out a spiral from top on a cylinder, now I want to make a nice finish. And cutting with a conical spring profile is the way to do it.
View 5 Replies View RelatedHow can i draw a SPRING around a circle ? like Attachment picture. (not in the Sketch) in the Part Modeling.
View 1 Replies View RelatedInventor offers us several options to design a coil of constant pitch with a tapering diameter. However, I am unable to create a coil with a taper and a changing pitch at the same time.
We are using Inventor 2013. I would like to produce similar parts as the attached 2D drawings in 3D, only with a changing pitch (distance between revolutions) per revolution. Can it be done? There is software for the CNC spring manufacturing machines to produce such parts. Therefore the proper inputs to produce these effectively and efficiently, are available somewhere.
The part I've been describing uses .09 diameter wire and has about 54 coils in about 8 inches. The starting inside diameter is about .53" and the pitch is about .27" the ending inside diameter is .109" +/- .01 with a pitch of about .091".
Here are 2D drawings of similar parts, the last (NF3) is closest to what we need.
How can i Draw a SPRING around a circle ?
View 3 Replies View RelatedI have a piece of steel that I need to flex. It is a piece of blue tempered spring steel pressed against the corner of a brass pressure transfer. The opposite end of the transfer is tangentlly constrained to a latching mechanism. When the latching mechanism is lifted, the transfer rotates slightly around a screw (made invisible) and the spring is flexed. When the latch is released, the spring returns the latch to the closed position. I have several other assemblies that use the same principal, but some with just a piece of mild steel used as a cover as well as a spring.
View 5 Replies View RelatedIs there a way to create a Coiled spring of 26 coils on an arc radius of 3.781inchs arc length of spring is 13.706inc
The major dia of the spring is 3/8 inch with the wire dia is NOT given
The original Hand done drawing are attached in PDF version 6 format
As for Inventor I'm using 2012. It is the first time I have come across this sort of problem I thought of doing a single coil and creating a sub assemble of it around a construction line arc rad with each coil mated and rotated at an angle to the other but then thought that there must be an easier way of creating this spring.
Inventor 2013 Pro
how can i make each end of the spring flat.How best to cut the end sections so the wire is flat
Invenotr 2012
I use inventor 2011 and i want to create a spring animation. I followed this video step by step but when i constrain the upside and the downside of the spring to those plate objects i get an error.
this is the video i followed:
[URL].....
I cant seem to find out how to assemble the spring to the rest of my item.
Will you be able to use the assembly if I do not provide the parts used(maximum 3 uploads)?
I have an assembly which has a few components suppressed.
My end results is another copy of the assembly (with copies of the all the parts) in another directory
Now i am able to create copies of un-suppressed parts using; (this allows me to SaveAs assembly components which are not suppressed)
DocumentsEnumerator = ThisDoc.Document.AllReferencedDocuments
And save a copy of the assembly using
ThisDoc.Document.SaveAs
I also added the fllowing snippet (which I am not sure what is does), but it does not work for me
Component.SkipDocumentSave = true
When I open the newly created assembly, I still see the suppressed components in the model browser
I want to either;
Skip saving the of the components in the model browser (i.e. the Assembly)
OR
Delete the suppressed parts in the Assembly, so that they do not save altogether
A multi-part question:
1.) How do you recommend I model a rectangular spring?
2.) How do I apply the concept from the initial question and apply a curve to the spring?
3.) How do I mimic the properties of a spring in animation?
I have a unique part that needs to be generated in IV. It is a sping that follows a curved path (see attachment). I do have complete information, just need to draw it in.
View 8 Replies View RelatedI would like to animate the model so that it moves like a whip antenna.
I would like to show the spring flexing back and forth with everything above the spring moving side to side as spring moves.
I have tried several ways to do this but have not had any luck. I haven't done a lot of animation.
I have attached the assembly and parts.
It doesn't have to perfect it's for a presentation.
IV2012 Product Design Suite
Windows XP Professional 32 Bit
I'm designing a hinged cover for something right now that will use a pair of gas extension springs for assisted opening. I'm currently working to figure out how much force it will take to open the cover using different values of spring - it's available in 50, 100, 150, 200, etc., lb versions.
I've tried running simulations using a force applied to the moving end of the gas spring, and I've trued running simulations using a spring joint applied between the fixed and and the moving end of the gas spring, and I'm getting dramatically different results between the two. For instance, using a 200 lb force shows me that I need about 25 extra lbs of force applied to the handle of the cover to open it, where when I use that same 200 lbs on a spring joint, I need 50-75 lbs to keep the cover closed, because it will open on its own.
I want to insert a spring in an assembly, and for that i will make a spring with the coil command. if i will squeese it between surfaces, will it resemble a spring? will the bindings come closer (i hope they are called bindings, otherwise tell me how they are called)?
View 2 Replies View RelatedI need a conical spring that can change in pitch as it tapers. Basically the spring starts in a compression style and tapers down to an expasion style. The CNC spring machines are capable to produce it, but am I able to, through Inventor? If not when will we have this feature capability?
View 7 Replies View RelatedOn the module generating inventor springs 2012 can generate a conical spring?
View 9 Replies View RelatedWhile using the frame generator's "Trim - Extend to Face" command on short members, the wrong end of the member is being trimmed. Is there a way to choose which end to trim on short members?
View 9 Replies View Related