I have unfolded a 3D model into a flat plate, however the bend lines/extents do not appear in ISO.dwg
I doubled clicked into the view to access 'Display Options'. However, I cannot tick the box to display bend extents as this option is shaded out (refer to attached screen dump).
If there is a way to remove the bend extents line when you create flat pattern. I don't mean in the drawing, the actual flat itself. My reasoning for this is when i transfer the flat into my nesting program, the bend extents lines transfer too. See attached img.
View 1 Replies View RelatedI have some users that use Solid Viewer that I am cosidering switching to Inventor LT. I use Inventor Pro. There is a feature in SolidWorks that let's them quickly display the overall extents; length, width, and height for quoting purposes. The tool creates a transparent box around the 3D model and displays these dimensions.
View 6 Replies View RelatedIs there some method to get the extents (i.e. bounding box) of a sketch? I'd like the vertical and horizontal dimension.
View 1 Replies View RelatedI am using IV ultimate 2013
just found about this add-in:[URL]
But its not working for me:
I ran the installer, created a sheet metal part and hit rebuild all, it did not create any proeprties, also tried to manually create the properteis then hit rebuild, no go.
I also did a search on my hardrive for the ApplicationPlugins, and placed the sheet metal folder in all of them(there were 3) tried again noto.
The add-in also does not appear in the add-in manager.
Or is there different what to get the flat pattern dimensions in 2013
When you create your own template part file and change the "Initial View Extents" setting in Document Settings on the Modelling Tab. Does this affect the behavior of the initial view extents when re-opening a part file created from this template?
FYI - I recently created a new template part file so that the sketch gridline spacing was more relevant to the size of parts I create. I like to use gridlines while in sketch mode because it is a good visual indicator that I'm in sketch mode. On opening a new part file that referenced to my new template, I noticed that the initial view extents meant only a couple of gridlines were visible due to the zoom level. I therefore tweaked my template file by increasing the initial view extents by a factor of 4 (400mm x 200mm).
The problem now is when opening a part file created from this template, the zoom level seems to snap to the customised view extents and not to the physical extents of the part. Right clicking the View Cube and re-setting the "Fit to View" has no effect. This feature seems broken now that I use modified initial view extents.
When I first upgraded to Inventor 2012 from Inventor 2010, I found that Inventor automatically created and populated three custom iProperties in the sheet metal environment. The props contained information for sheet metal style and sheet metal extents (width and length).
With a fresh installation, Inventor does not seem to be creating the custom props any more. Did I miss a setting or has the feature been discontinued already?
How to make Automatic Update propeties for Flat Pattern Extens. I have write code and setting rules trigerred by event (Before save, Any model Parameter Change) but if some parameter change properties isn't automatic update. So could some one tell me how to solve this problem.
Part with iLogic code is attached
We use the snippets from iLogic on all of our parts to measure the length, width or height of our parts. However, we have noticed that when a 'Move Face' operation or a 'Replace Face' operation is used, the length measured does not seem to take into account the Move/Replace operations.
Are the Move/Replace operations different than other features like Extrude/Revolve? Is there something "ghost-like" about them??? The edges work fine on the drawing side, so I'm not sure what is different. Maybe it is the iLogic snippet?
In regards to it being the snippet, is there another code I can use that doesn't require specific feature or part information built in?
Inventor 2013 Product Design Suite
Vault Professional 2013
Windows7 x64
Autodesk Inventor Certified Professional
I'm trying to use the cut across bend feature on a sheet metal part. However, when I check cut across bend, it grays out all of the other cutout options, and only has thickness as the only option. This is perplexing to me, because I can't think of too many times I'd need this option other than when there is more than one thickness of material I need to manipulate the profile onto.
I was to understand that this "cut across bend" is for use similar to the "normal cutout" command in solid edge? Keeps the cut perpendicular to the sheet face in a sheet metal part.
Cybertron PC
Intel Core i5-3470 CPU @ 3.20 GHz 3.60 GHz
16.0 GB RAM
Windows 7 Professional 64 Bit
3D Connexion Space Pilot
Inventor Professional 2014
Autocad Mechanical 2014
I attached an IPT file that a customer sent us to manufacture for them.It's a rectangular aluminum tube with two bends.In the IDW when I try to place center points and dimension the radius it is not recognized.The original file was a STEP.
View 9 Replies View RelatedUnder the modify tab in a part file, I can drop down and click "bend part." We have a bunch of frames made out of stock tubing that are welded together, then bent as a whole. Is there a way to bend at the assembly? I want the model to represent the production process. I don't want to have to bend each tube alone, then reassemble. That would double my parts/part numbers.
View 9 Replies View RelatedI have been trying to bend a larger radius on a corner bend but i can not seem to be able to . I start out with a face of 46" x 82" i want to put a 1/2" bend up then a 1/2" bend out to make a z shape i'm using as a material .109 stainless steel and i want to end up with a 1/2" on the inside corners so that when i'm done i can flatten it out to get the proper sheer size for the piece the metal brake i'm using has a 1/2" die in thats why i trying to figure this out is their any way to put this kind of radius on the sheet metal bends.
View 2 Replies View RelatedUsing Inventor 2012 is it possible to change the down 90 to Bend FarSide 90?
View 4 Replies View RelatedI'm trying to do a usable and real flat pattern for a laser cut on this type of part and I'm not able to do a cut across bend or other wrap around face feature.
Any method to do such a feature ?
I want to do a simple bend of a cylinder. That is, I have made a 40inch length and want to bend it at several places.
I keep finding a reference to bend part but the tool does not exist in Inventor.
I have created a pipe using sweep through 2 planes and 3d sketch. I want a specific bend on that pipe to be extracted for drawing purpose. How do I do that ?
View 9 Replies View RelatedIf i have even used the correct technique but how do i perform the bends in the flat bar so as the bottom and top section are vertical and the small mid section is on the angle. At the moment the mid section is displayed vertical when using the cub please see attached files.
View 4 Replies View RelatedI cannot figure out how to dual dimension a bend like so:
DIRECTION DEGREES RIMPERIAL [RMETRIC]
e.g. DOWN 90 R1/2"[13] preferred
or DOWN 90 R1/2"[R13] okay
There should be a degree symbol after the 90 in my examples but I can't figure out how to type it here. I can get DOWN 90 R1/2"[DOWN 90 R13] but it's too long.
Is there a way to make Inventor automatically add a note, along the bend line, indicating bend direction, number of degrees and bend radius?
Also, in 2013, where are the bend tables located? I've checked the help file, and it's telling me cprogram filesautodeskinventor 2013design data
I followed that path, but I do not have the "design data" folder it's calling for.
Inventor 2014 LT / have run into a problem in a throw-away project I"m working on.
A simple example is to create a piece of 3x5x.125 flat bar, add a sketch giving you a bend line and bend the end of it. Now try to mirror the whole thing giving you a 3x10x.125 flat bar bent on both ends.
FWIW: My project isn't this simple - I know I can just make the FB and bend both ends ... this is an example of mirroring a bend not working.
I am trying to save copy as dxf without bendlines so I can directly import the file into my waterject CAM software. There has to be a way to tell it not to add the benline layer.
View 7 Replies View RelatedI have a sheet metal door with a little bracket that gets welded to the inside lip through a cut-out in the face of the door. (see assembly)
I can't get the cut-out to line up flush with the inside lip of the door, as that is where the brackets gets welded to. the current aseembly is set-up the way I want, but I can't get a flat pattern on the door, becasue of the cut going across the bend.
I have checked off the "cut across bend" in the cut dialogue box, but this leaves a small (~1/32) lip in the cut-out and runs interference in the placement of the bracket.
Inventor Pro Suite 2013
Sean Farr
Product Designer at TESInc.ca
Inventor Professional 2014-Update 2 - AutoCAD Electrical 2014
Win7-x64 | ASUS P8Z77-V | i7 3770 -3.4 GHz | 32GB RAM |
240GB SSD | nVidia GTX 670 4GB - 320.49
I am not sure what I am doing wrong but when I use the bend tool I am getting weird results. Does the surface to be bent have to be planar? See photo attachment.
View 4 Replies View RelatedCreate a new sheet metal part make it a box of any size add four flanges then create a flat pattern. Save the file then create a drawing view of the flat pattern. All well and good so far... Now create a Table using the flat pattern view as the source, which creates a Bend table just fine.
Place the table on the sheet and Tags are added to the bend lines which is wonderful and great. Now try to move a tag.... BZZZZZZ your time is up you can't.
Yet in your Sheet Metal Annotations in Drawing - Wiki Help page in the Procedures - Create or edit a bend table - Create bend tags section it states:
Tip Drag the bend tag text away from the original position to add a leader to the bend tag. Is this a bug or something not set right on my system?
Manufacturer: Dell
Model: Precision T3500
Video Card: NVIDIA Quadro FX 3700
Video Driver: 8.17.12.6779
Processor: Intel® Xeon® CPU
W3503 @ 2.40GHz 2.40 GHz
Installed memory (RAM): 4.00 GB
System type: 64-bit Operating System
How do i get the bend order annotation # with vba?
View 1 Replies View RelatedI have some code that find the length of a bend and it works great until there is a cut operation that passes through the edge of the part and through the bend. When this cut exists the systems recognizes the single bend 2 times which is fineand it should, just that it should also then be able to determine the length of each segment. It appears to be providing the length of the first segment twice. Any way to get either the segmented lengths or the length of the bend without the cut? I need a total length and the code below gives wrong data for the one edge length. the attached file shows what I mean.
Sub Bends()
Dim oDoc As PartDocument
Set oDoc = ThisApplication.ActiveDocument
[Code]....
I'm trying to cut across bend in the attached part. Usually this thing works quite good, but for some reason it's not letting me do it. What Am I doing wrong? How can I do it?
Inventor 2012 Pro.
I7 workstation
I want to make this part that bend 15 degree at 800 mm from bottom. In my attempt.
First, I bend it 15 degree.
And, make flange from Face and upper flange then I stuck with error.
Is there a way to preload information into Inventor in regards to the break press such as the dies being used or the ones available so the when the computer is deciding a bending radius,it know what tool we have?
Currently the bend radius is set to "radius", which i am assuming is default, but I can't figure out how to change that either, and depending on the thickness it will change, but like today it said I would need a 1/16th inch radius, but we don't have a 1/16th inch die,it is an 85 degree air bending setup,and has a 4 way die with smaller and bigger openings.
Any way of drawing an edge bend on a flat bit of copper so I can flat pattern it for the guys on the shop floor to make.
The problem comes with the edge bend, I have provided a picture of a simple bit of copper with various flat bends and a single edge bend. As the flat pattern shows to the right the edge bend is not flattered, This was drawn using a sketch the profile then using "face" . This is why I assume it does not work in flat pattern.
Is it possible to draw an edge bend with a command to allow it to flat pattern? if so which command and how?
autodesk 2012
Windows 7.