I'm trying to cut across bend in the attached part. Usually this thing works quite good, but for some reason it's not letting me do it. What Am I doing wrong? How can I do it?
Inventor 2012 Pro.
I7 workstation
I have a structrual rectangular tube as shown in the picture below. I need to fold the four flanges inward to create a sort of point or pyramid.
View 9 Replies View RelatedI am trying to model a plastic part which is attached to each other on one side of the edge and it snaps into each other on the other side. I was able to manage the hald section of this part but not sure how to do other half.
how to do these plastic parts?
When I create part .ipt directly in assembly .iam, I can make it adaptive. I'm doing the projection of geometry. Detail goes adaptive. Geometry appears as a link.
But if I put in the assembly finished parts or remove part created in the assembly, and then insert it back, the adaptability of parts did not get to create. Then the projection geometry inserts usual nonadaptive geometry without reference.
Can I make a finished part adaptive, without creating a component at the place in this assembly?
Is there any way to create flat pattern of a part I attached ?
View 3 Replies View RelatedI want to create a structure using the attached part geometry, what would be the best way to make the crosses coincident with the two long columns? (just like the 2 at the top but without having to manually trim each line, if it could be constrained to variable parameters even better)
The structure has the same geometry on all four sides so i intend to circular patern the frame generator components around the Z axis, any better workflows?
Can a curved section with bend be applied to sheet metal part.I make extrusion for easier clarity.I am wanting to place the curved section (extrusion for demonstration purpose) with bend in sheet metal part but all created in the sheet metal environment.
View 6 Replies View RelatedI'm trying to create a content center part with a decal attached to the model. The problem I am facing it that the decal is not adjusting in size when the ipt is placed from the content center. The decal does adjust in the original ipt.
View 2 Replies View RelatedI've attached an example of a workflow we use to make different instances of products.part1 gets assembled in assembly1 which then gets derived in part2 to receive a bend.We use assembly1 in one place and part2 in another.(this is a simplified example, made with IV2013 SP1.1)
In part1, if you add the thread feature, the "bend part" feature in part2 fails after updating.This also happens if you try to add a "bend part" to part1 AFTER the thread feature, if the bend is present beforehand it does work.
Having the bend before the thread feature in part1 doesn't work with our workflow, because we need the assembly1 to be straight.In short, the thread feature is causing problems with "bend part".
I can't say if this problem was present in previous versions or even in the previous service pack since we don't use this workflow that often, especially with threaded parts, but i hope this can get fixed with a hotfix.
Using IV2014 Pro SP1 update 1, Win7-64bit
I have attached and image to a surface of a part and when I bring it back to AutoCad I can not see the image.
View 1 Replies View RelatedI'm trying to use the cut across bend feature on a sheet metal part. However, when I check cut across bend, it grays out all of the other cutout options, and only has thickness as the only option. This is perplexing to me, because I can't think of too many times I'd need this option other than when there is more than one thickness of material I need to manipulate the profile onto.
I was to understand that this "cut across bend" is for use similar to the "normal cutout" command in solid edge? Keeps the cut perpendicular to the sheet face in a sheet metal part.
Cybertron PC
Intel Core i5-3470 CPU @ 3.20 GHz 3.60 GHz
16.0 GB RAM
Windows 7 Professional 64 Bit
3D Connexion Space Pilot
Inventor Professional 2014
Autocad Mechanical 2014
I attached an IPT file that a customer sent us to manufacture for them.It's a rectangular aluminum tube with two bends.In the IDW when I try to place center points and dimension the radius it is not recognized.The original file was a STEP.
View 9 Replies View RelatedUnder the modify tab in a part file, I can drop down and click "bend part." We have a bunch of frames made out of stock tubing that are welded together, then bent as a whole. Is there a way to bend at the assembly? I want the model to represent the production process. I don't want to have to bend each tube alone, then reassemble. That would double my parts/part numbers.
View 9 Replies View RelatedI have a sketchedsymbol with leaderline. How can I get the BOM of the item this is attached to? I don't see any referenced way to do this. I assume it's possible because a balloon can get this info.
The full extent of what I want to do is to create a split balloon symbol. The top portion of the balloon with hold the detail number, the botton half will hold a user prompted text entry.
Win7 x64 - 16gb ram
i7 3610qm
FirePro M4000
Inventor 2013
ETO 6.1
I have been trying to bend a larger radius on a corner bend but i can not seem to be able to . I start out with a face of 46" x 82" i want to put a 1/2" bend up then a 1/2" bend out to make a z shape i'm using as a material .109 stainless steel and i want to end up with a 1/2" on the inside corners so that when i'm done i can flatten it out to get the proper sheer size for the piece the metal brake i'm using has a 1/2" die in thats why i trying to figure this out is their any way to put this kind of radius on the sheet metal bends.
View 2 Replies View RelatedUsing Inventor 2012 is it possible to change the down 90 to Bend FarSide 90?
View 4 Replies View RelatedI'm trying to do a usable and real flat pattern for a laser cut on this type of part and I'm not able to do a cut across bend or other wrap around face feature.
Any method to do such a feature ?
I want to do a simple bend of a cylinder. That is, I have made a 40inch length and want to bend it at several places.
I keep finding a reference to bend part but the tool does not exist in Inventor.
I have created a pipe using sweep through 2 planes and 3d sketch. I want a specific bend on that pipe to be extracted for drawing purpose. How do I do that ?
View 9 Replies View RelatedIf i have even used the correct technique but how do i perform the bends in the flat bar so as the bottom and top section are vertical and the small mid section is on the angle. At the moment the mid section is displayed vertical when using the cub please see attached files.
View 4 Replies View RelatedI have unfolded a 3D model into a flat plate, however the bend lines/extents do not appear in ISO.dwg
I doubled clicked into the view to access 'Display Options'. However, I cannot tick the box to display bend extents as this option is shaded out (refer to attached screen dump).
I cannot figure out how to dual dimension a bend like so:
DIRECTION DEGREES RIMPERIAL [RMETRIC]
e.g. DOWN 90 R1/2"[13] preferred
or DOWN 90 R1/2"[R13] okay
There should be a degree symbol after the 90 in my examples but I can't figure out how to type it here. I can get DOWN 90 R1/2"[DOWN 90 R13] but it's too long.
Is there a way to make Inventor automatically add a note, along the bend line, indicating bend direction, number of degrees and bend radius?
Also, in 2013, where are the bend tables located? I've checked the help file, and it's telling me cprogram filesautodeskinventor 2013design data
I followed that path, but I do not have the "design data" folder it's calling for.
Inventor 2014 LT / have run into a problem in a throw-away project I"m working on.
A simple example is to create a piece of 3x5x.125 flat bar, add a sketch giving you a bend line and bend the end of it. Now try to mirror the whole thing giving you a 3x10x.125 flat bar bent on both ends.
FWIW: My project isn't this simple - I know I can just make the FB and bend both ends ... this is an example of mirroring a bend not working.
I am trying to save copy as dxf without bendlines so I can directly import the file into my waterject CAM software. There has to be a way to tell it not to add the benline layer.
View 7 Replies View RelatedI have a sheet metal door with a little bracket that gets welded to the inside lip through a cut-out in the face of the door. (see assembly)
I can't get the cut-out to line up flush with the inside lip of the door, as that is where the brackets gets welded to. the current aseembly is set-up the way I want, but I can't get a flat pattern on the door, becasue of the cut going across the bend.
I have checked off the "cut across bend" in the cut dialogue box, but this leaves a small (~1/32) lip in the cut-out and runs interference in the placement of the bracket.
Inventor Pro Suite 2013
Sean Farr
Product Designer at TESInc.ca
Inventor Professional 2014-Update 2 - AutoCAD Electrical 2014
Win7-x64 | ASUS P8Z77-V | i7 3770 -3.4 GHz | 32GB RAM |
240GB SSD | nVidia GTX 670 4GB - 320.49
I am not sure what I am doing wrong but when I use the bend tool I am getting weird results. Does the surface to be bent have to be planar? See photo attachment.
View 4 Replies View RelatedCreate a new sheet metal part make it a box of any size add four flanges then create a flat pattern. Save the file then create a drawing view of the flat pattern. All well and good so far... Now create a Table using the flat pattern view as the source, which creates a Bend table just fine.
Place the table on the sheet and Tags are added to the bend lines which is wonderful and great. Now try to move a tag.... BZZZZZZ your time is up you can't.
Yet in your Sheet Metal Annotations in Drawing - Wiki Help page in the Procedures - Create or edit a bend table - Create bend tags section it states:
Tip Drag the bend tag text away from the original position to add a leader to the bend tag. Is this a bug or something not set right on my system?
Manufacturer: Dell
Model: Precision T3500
Video Card: NVIDIA Quadro FX 3700
Video Driver: 8.17.12.6779
Processor: Intel® Xeon® CPU
W3503 @ 2.40GHz 2.40 GHz
Installed memory (RAM): 4.00 GB
System type: 64-bit Operating System
How do i get the bend order annotation # with vba?
View 1 Replies View RelatedI have some code that find the length of a bend and it works great until there is a cut operation that passes through the edge of the part and through the bend. When this cut exists the systems recognizes the single bend 2 times which is fineand it should, just that it should also then be able to determine the length of each segment. It appears to be providing the length of the first segment twice. Any way to get either the segmented lengths or the length of the bend without the cut? I need a total length and the code below gives wrong data for the one edge length. the attached file shows what I mean.
Sub Bends()
Dim oDoc As PartDocument
Set oDoc = ThisApplication.ActiveDocument
[Code]....
I want to make this part that bend 15 degree at 800 mm from bottom. In my attempt.
First, I bend it 15 degree.
And, make flange from Face and upper flange then I stuck with error.