AutoCAD Inventor :: Dual Dimension A Bend

Apr 11, 2013

I cannot figure out how to dual dimension a bend like so:

DIRECTION DEGREES RIMPERIAL [RMETRIC]

e.g. DOWN 90 R1/2"[13]  preferred

or   DOWN 90 R1/2"[R13] okay

 There should be a degree symbol after the 90 in my examples but I can't figure out how to type it here. I can get DOWN 90 R1/2"[DOWN 90 R13] but it's too long.

View 3 Replies


ADVERTISEMENT

AutoCAD Inventor :: Can't Dimension A Bend

Jun 7, 2013

I attached an IPT file that a customer sent us to manufacture for them.It's a rectangular aluminum tube with two bends.In the IDW when I try to place center points and dimension the radius it is not recognized.The original file was a STEP.

View 9 Replies View Related

AutoCAD Inventor :: Dual Dimension Display

Oct 9, 2012

Any way to show dual dimensions as shown on the right rather than the one which we get on the left 

Config :: Intel (R) Xeon (R) CPU E31245 @ 3.30 GHz, 16.0 GB, 64bit win7
Inventor 2013 and Vault Basic 2013

View 9 Replies View Related

AutoCAD Inventor :: Show Angular Dimension In Dual Units?

Sep 9, 2012

is there any way I can place dimension on drawing that would be in dual units (in decimal degrees and in deg min sec)?

I did not find this possible so far.

View 2 Replies View Related

AutoCAD Inventor :: How To Convert Normal Dimension To Driven Dimension Through ILogic

May 28, 2013

I have one problem in ilogic "How to convert the normal dimension to driven dimension through ilogic"

View 4 Replies View Related

AutoCAD Inventor :: Best CPU To Use For Inventor Between I7 And Dual Xeon System

May 16, 2012

Upgrading to a new computer.

1. What is the best CPU to use for Inventor between the i7 and the a Dual Xeon System

2. Would 32GB of memory easily cover all modelling such as assemblies?

3. Any advantage of having 2 x SSD instaed of 1 x SSD

4. Looking at the Nvidia GTX690 graphics card....this should be a good card

View 4 Replies View Related

AutoCAD Inventor :: Make Radius Dimension Diameter Dimension?

Feb 23, 2013

how to make a radius dimension a diameter dimension? I have Inventor Profession 2013.

View 1 Replies View Related

AutoCAD Inventor :: Override A Dimension To Create A Basic Dimension?

Jun 27, 2011

Is there a way to override a dimension and have it shown as a GD&T Basic dimension. I can override a dimension with the text option but not with a box around the letter. It sounds strange to do this but the letter represents a dimension in a chart format that are Basic dimensions.

View 9 Replies View Related

AutoCAD Inventor :: Make Linear Dimension A Diameter Dimension?

Jan 27, 2012

Is there a way to make the linear dimension a diameter dimension?

View 9 Replies View Related

AutoCAD Inventor :: Dual Weights On IDW?

Apr 5, 2013

It it possible to create a design spec table so that it can import the weight from the model and display it in both kg and lbs?

View 5 Replies View Related

AutoCAD Inventor :: Cut Across Bend Feature

Dec 27, 2013

I'm trying to use the cut across bend feature on a sheet metal part. However, when I check cut across bend, it grays out all of the other cutout options, and only has thickness as the only option. This is perplexing to me, because I can't think of too many times I'd need this option other than when there is more than one thickness of material I need to manipulate the profile onto.

I was to understand that this "cut across bend" is for use similar to the "normal cutout" command in solid edge? Keeps the cut perpendicular to the sheet face in a sheet metal part.
 
Cybertron PC
Intel Core i5-3470 CPU @ 3.20 GHz 3.60 GHz
16.0 GB RAM
Windows 7 Professional 64 Bit
3D Connexion Space Pilot
Inventor Professional 2014
Autocad Mechanical 2014

View 3 Replies View Related

AutoCAD Inventor :: Is There A Way To Bend At Assembly

Feb 14, 2012

Under the modify tab in a part file, I can drop down and click "bend part."  We have a bunch of frames made out of stock tubing that are welded together, then bent as a whole.  Is there a way to bend at the assembly?  I want the model to represent the production process.  I don't want to have to bend each tube alone, then reassemble. That would double my parts/part numbers.

View 9 Replies View Related

AutoCAD Inventor :: Dual Dimensions In A Sketch

Jun 6, 2012

How do I change one of the dimensions in my sketch to be metric while maintaining the rest as a standard dimensions?

See attached pic.

View 9 Replies View Related

AutoCAD Inventor :: Dual Dimensions In Drawings?

Apr 29, 2012

How do I show dual dimension in Inventor drawing?

View 5 Replies View Related

AutoCAD Inventor :: How To Change Radius On A Bend

Oct 21, 2011

I have been trying to bend a larger radius on a corner bend but i can not seem to be able to . I start out with a face of 46" x 82"  i want to put a 1/2" bend up then a 1/2" bend out to make a z shape i'm using as a material .109 stainless steel and i want to end up with a 1/2" on the inside corners so that when i'm done i can flatten it out to get the proper sheer size for the piece the metal brake i'm using has a 1/2" die in thats why i trying to figure this out is their any way to put this kind of radius on the sheet metal bends.

View 2 Replies View Related

AutoCAD Inventor :: Change The Down 90 To Bend FarSide 90?

Dec 2, 2013

Using Inventor 2012 is it possible to change the down 90 to Bend FarSide 90?

View 4 Replies View Related

AutoCAD Inventor :: Cut Across Bend Around A Rolled Tube

Feb 14, 2012

I'm trying to do a usable and real flat pattern for a laser cut on this type of part and I'm not able to do a cut across bend or other wrap around face feature.

Any method to do such a feature ?

View 7 Replies View Related

AutoCAD Inventor :: Bend A Cylinder At Several Places

Dec 27, 2012

I want to do a simple bend of a cylinder. That is, I have made a 40inch length and want to bend it at several places. 

I keep finding a reference to bend part but the tool does not exist in Inventor. 

View 3 Replies View Related

AutoCAD Inventor :: Retrieve A Bend From Sweep?

Oct 4, 2012

I have created a pipe using sweep through 2 planes and 3d sketch. I want a specific bend on that pipe to be extracted for drawing purpose. How do I do that ?

View 9 Replies View Related

AutoCAD Inventor :: How To Perform Bend In Flat Bar

Feb 21, 2012

If i have even used the correct technique but how do i perform the bends in the flat bar so as the bottom and top section are vertical and the small mid section is on the angle. At the moment the mid section is displayed vertical when using the cub please see attached files.

View 4 Replies View Related

AutoCAD Inventor :: Bend Extents Not Visible

Oct 21, 2013

I have unfolded a 3D model into a flat plate, however the bend lines/extents do not appear in ISO.dwg

I doubled clicked into the view to access 'Display Options'. However, I cannot tick the box to display bend extents as this option is shaded out (refer to attached screen dump).

View 7 Replies View Related

AutoCAD Inventor :: Bend Notes On Drawing

Aug 13, 2012

Is there a way to make Inventor automatically add a note, along the bend line, indicating bend direction, number of degrees and bend radius?

Also, in 2013, where are the bend tables located? I've checked the help file, and it's telling me cprogram filesautodeskinventor 2013design data

I followed that path, but I do not have the "design data" folder it's calling for.

View 3 Replies View Related

AutoCAD Inventor :: Cannot Mirror A Bend In 2014

Jun 22, 2013

Inventor 2014 LT / have run into a problem in a throw-away project I"m working on.

A simple example is to create a piece of 3x5x.125 flat bar, add a sketch giving you a bend line and bend the end of it. Now try to mirror the whole thing giving you a 3x10x.125 flat bar bent on both ends.  

FWIW: My project isn't this simple - I know I can just make the FB and bend both ends ... this is an example of mirroring a bend not working.

View 2 Replies View Related

AutoCAD Inventor :: Save DXF Without Bend Lines

Dec 31, 2011

I am trying to save copy as dxf without bendlines so I can directly import the file into my waterject CAM software.  There has to be a way to tell it not to add the benline layer.

View 7 Replies View Related

AutoCAD Inventor :: Sheet Metal - Cut Across Bend

Dec 20, 2012

I have a sheet metal door with a little bracket that gets welded to the inside lip through a cut-out in the face of the door. (see assembly)

I can't get the cut-out to line up flush with the inside lip of the door, as that is where the brackets gets welded to. the current aseembly is set-up the way I want, but I can't get a flat pattern on the door, becasue of the cut going across the bend.

I have checked off the "cut across bend" in the cut dialogue box, but this leaves a small (~1/32) lip in the cut-out and runs interference in the placement of the bracket. 

Inventor Pro Suite 2013
Sean Farr
Product Designer at TESInc.ca
Inventor Professional 2014-Update 2 - AutoCAD Electrical 2014
Win7-x64 | ASUS P8Z77-V | i7 3770 -3.4 GHz | 32GB RAM |
240GB SSD | nVidia GTX 670 4GB - 320.49

View 2 Replies View Related

AutoCAD Inventor :: Bend Along Non-planar Surface?

Dec 26, 2013

I am not sure what I am doing wrong but when I use the bend tool I am getting weird results. Does the surface to be bent have to be planar? See photo attachment.

View 4 Replies View Related

AutoCAD Inventor :: Why Can't Move Bend Tags

May 13, 2011

Create a new sheet metal part make it a box of any size add four flanges then create a flat pattern.  Save the file then create a drawing view of the flat pattern.  All well and good so far...  Now create a Table using the flat pattern view as the source, which creates a Bend table just fine. 

Place the table on the sheet and Tags are added to the bend lines which is wonderful and great.  Now try to move a tag.... BZZZZZZ your time is up you can't.  

Yet in your Sheet Metal Annotations in Drawing - Wiki Help page in the Procedures - Create or edit a bend table - Create bend tags section it states: 
 
Tip Drag the bend tag text away from the original position to add a leader to the bend tag. Is this a bug or something not set right on my system?

Manufacturer: Dell
Model: Precision T3500
Video Card: NVIDIA Quadro FX 3700
Video Driver: 8.17.12.6779
Processor: Intel® Xeon® CPU
W3503  @ 2.40GHz   2.40 GHz
Installed memory (RAM): 4.00 GB
System type: 64-bit Operating System

View 8 Replies View Related

AutoCAD Inventor :: Bend Order Annotation With VBA?

Nov 3, 2011

How do i get the bend order annotation # with vba?

View 1 Replies View Related

AutoCAD Inventor :: How To Find Length Of A Bend

Oct 6, 2011

I have some code that find the length of a bend and it works great until there is a cut operation that passes through the edge of the part and through the bend. When this cut exists the systems recognizes the single bend 2 times which is fineand it should, just that it should also then be able to determine the length of each segment.  It appears to be providing the length of the first segment twice. Any way to get either the segmented lengths or the length of the bend without the cut?  I need a total length and the code below gives wrong data for the one edge length.   the attached file shows what I mean.

Sub Bends()
Dim oDoc As PartDocument
Set oDoc = ThisApplication.ActiveDocument

[Code]....

View 3 Replies View Related

AutoCAD Inventor :: How To Cut Across Bend In The Attached Part

Oct 31, 2011

I'm trying to cut across bend in the attached part. Usually this thing works quite good, but for some reason it's not letting me do it. What Am I doing wrong? How can I do it?

Inventor 2012 Pro.
I7 workstation

View 3 Replies View Related

AutoCAD Inventor :: Bend 15 Degree At 800 Mm From Bottom

Dec 6, 2012

I want to make this part that bend 15 degree at 800 mm from bottom. In my attempt.

First, I bend it 15 degree.

And, make flange from Face and upper flange then I stuck with error.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved