AutoCAD Inventor :: Edge Bend For Flat Pattern
Jul 31, 2013
Any way of drawing an edge bend on a flat bit of copper so I can flat pattern it for the guys on the shop floor to make.
The problem comes with the edge bend, I have provided a picture of a simple bit of copper with various flat bends and a single edge bend. As the flat pattern shows to the right the edge bend is not flattered, This was drawn using a sketch the profile then using "face" . This is why I assume it does not work in flat pattern.
Is it possible to draw an edge bend with a command to allow it to flat pattern? if so which command and how?
autodesk 2012
Windows 7.
View 6 Replies
ADVERTISEMENT
Dec 7, 2011
I am trying to create a command to display the bend information in the model Flat pattern. We do not always create a Idw for parts that we have special dies to form. This creates a problem though if the flat pattern bends are the wrong direction because then it is lasered with the bad side of the material to the outside of the part. The only way to know the bend direction is to create a view on an idw just to check this.
I want to open the flat pattern in the ipt and invoke a command to display the bend information on the screen. Need getting a collection of the bend lines in the flat pattern?
View 7 Replies
View Related
Jan 2, 2012
I am trying to export geometry found in a flat pattern sketch overlaid onto the flat pattern.
Since I am creating the output file manually I gather the flat pattern boundaries and bend center lines for output to a file.
When I add flat pattern sketch entities to the mix they do not overlay properly. What matrix would I have to push the sketch entities through to get them to the same coordinates as the flat pattern?
View 1 Replies
View Related
Feb 21, 2012
If i have even used the correct technique but how do i perform the bends in the flat bar so as the bottom and top section are vertical and the small mid section is on the angle. At the moment the mid section is displayed vertical when using the cub please see attached files.
View 4 Replies
View Related
Mar 21, 2013
If there is a way to remove the bend extents line when you create flat pattern. I don't mean in the drawing, the actual flat itself. My reasoning for this is when i transfer the flat into my nesting program, the bend extents lines transfer too. See attached img.
View 1 Replies
View Related
Feb 17, 2010
I can't find a way to create multi flat patters in one part from a lofted sheetmetal part. Also, didn't the developers fix the 'can't make a flat pattern from a derived part'?
IV 2010 Suite
Digital Storm PC:
EVGA & Intel components
Win 7 Pro 64 bit
View 5 Replies
View Related
Mar 2, 2012
My next challenge with my rolled cone bottom is to place an oval in the cone that will give the right edges for the lazer pattern. If I create the cut while in the formed shape the edges are not perpendicular to the face in the flat pattern. If I place the cut in the flat pattern, it is suppressed when the part is returned to the formed state.
In other packages I would unfold the part, place the cut, and then refold it retaining the cut. How do we deal with this situation here?
View 2 Replies
View Related
Mar 14, 2006
I want to make dxf files from a flatpattern with ApprenticeServer in a VB6 project. I tried this code but I get a Error 5 on the line :
oDataIO.WriteDataToFile sOut, strFilenaam
What's wrong?
Public Sub Maak_UitslagDXF_Appr(strFilenaam As String)
Dim oApprenticeServerApp As New ApprenticeServerComponent
Dim oPartdoc As ApprenticeServerDocument
Set oPartdoc = oApprenticeServerApp.Open(strFilenaam)
[Code]....
View 6 Replies
View Related
Dec 14, 2012
My flat pattern of a sheet metal part fails when I added strenthening Press ribs to the middle of the part using an iFeature.
I know Inventor is not capable of flattening embossed sheetmetal but is there a way to still get the flat pattern & ignore the formed areas?
Seems to me I was able to add some model features in the past like bosses, extruded holes KO's etc & I could still make a flat pattern.
I know I can use derived part to do it but that adds complications.
IV 2012 SP2
Inventor Suite 2013 Ultimate
View 3 Replies
View Related
Aug 26, 2012
It's my first time using sheet metal in a drawing and I can't figure out how to show flat pattern in the drawing. When I insert the base view into my drawing, the bottom to "Sheet Metal View" to "Flat Pattern" is shown, but it's ghosted out so I can't select it. Is there something I have to do in the part drawing in order to activate this feature?
View 2 Replies
View Related
May 30, 2012
So, I have an assembly with a sheet metal part and a lot of pressed studs, spacers, weld nuts. I'd like to do a flat pattern with these parts in it in order to give their positions to manufacture, because they have to be pressed and weld in flat pattern phase, before bending.
Is there any easy way to do this (instead of saving flat pattern as SAT and insert every components again)?
View 3 Replies
View Related
Nov 17, 2011
I have designed a hopper using the lofted flange command. It is a 24" sq going to an 8" diameter. I would like to apply the rip feature to make (4) separate sections for this hopper so that (4) separate pieces can be cut on a waterjet machine. I can make it so that only (2) flat patterns are required, (2) pieces cut for each.
Can this be done in Inventor 2011? Also, can you recommend a good book on Sheetmetal in Inventor?
View 2 Replies
View Related
Nov 16, 2010
I am trying to develop a macro that exports all flat patterns for sheet metal components. I haven't been able to get the following code to work. It give the error message "The document you are trying to save is not a drawing document"
Sub PublishDXF() Dim DXFAddIn As TranslatorAddIn Set DXFAddIn = ThisApplication.ApplicationAddIns.ItemById("{C24E3AC4-122E-11D5-8E91-0010B541CD80}") Dim oDocument As PartDocument Set oDocument = ThisApplication.ActiveDocument Dim oContext As TranslationContext
[Code] .......
View 9 Replies
View Related
May 3, 2012
I just got around to installing my subscription upgrade from INV PRO 2012 to 2013. I am having trouble getting sheet metal flats to show up in the idw's. The folded parts are visible, solid parts are visible, etc. The problem seems to be specific to flat patterns. I have attached a screen shot of a sample part.
When I hover the mouse over where the flat pattern should be, the red dashed box which usually encloses the view shows up, however it is tiny. Barely the size of the view label.
View 4 Replies
View Related
Feb 14, 2013
I'm having difficulty with a sheet metal part creating a flat pattern for it. The shape is an ellipse with the dimensions shown in the second picture. When I attempt to create a flat pattern it just shows the side of the part. The sheet metal defaults are correct for the part and it was ripped to created a base point for the pattern. I need to create a DXF for manufacture. I would just use the flat pattern it gives me and mirror it twice to create a pattern but it doesn't factor in the radius of the part. How to create a correct flat pattern for this item?
View 5 Replies
View Related
Sep 6, 2013
how can i get a flat pattern for an object with more than one rip? it only gives me half the flat pattern.
example for company privacy
inventor 2014
Windows 7 Pro 64
i7-3820 3.6GHz
32 GB RAM
2 TB HD
NVIDIA GeForce GTX 660 Ti
Liquid Cooled
3D Connexion
CM Storm
twin ASUS LED
View 1 Replies
View Related
May 3, 2012
I'm unable to create a flat pattern .
View 5 Replies
View Related
Mar 8, 2013
I was wondering if there is any possible way to flat pattern a coil. Attached is a picture of what I am trying to flat pattern. Its a quarter turn of a full coil.
View 7 Replies
View Related
Dec 19, 2011
A rather simple sheetmetal part won't result in a flat pattern. Pls. see attached screendumps.
The problem starts with the contour roll. Surpressing this contour roll feature (and dependent featured flange) results in a OK flat pattern.
IV Pro 2012, Win 7-64 Ult.
View 1 Replies
View Related
Mar 7, 2013
I want to creat a flatpattern of an iregulary cut cylinder that was made in the standard .ipt world and is now converted into a sheetmetal. I want to "Unroll" the piece out so can see the shape of it as a flat piece. Picture of it is attached.
View 6 Replies
View Related
Apr 11, 2012
I attached the iLogic code which is automatically creating dwg drawing (script borrowed from one of the discussion group users), also it creates 4 views. I`m just wondering how to add flat pattern ?
View 7 Replies
View Related
Feb 5, 2013
I am trying to write an external iLogic rule that will export the unfolded model of a sheet metal part in a drawing from a rule triggered in the .idw. These drawings will contain only one model reference. The reason for doing this from the drawing are as follows:
1) The location of the resulting .stp file must be the same directory as the .idw file. our file structure does not co-locate these files so the drawing path is required to locate the .stp file.
2) The current Drawing Rev level is to appended to the .stp file name. We do not populate the Rev iProperty in the part.
I have scabbed together some code from verious deep dark corners on the internet and Have arrived at the code posted below, but It errors during the .stp file creation with the following:
Error Message:
Error in rule: STEP Export With Rev, in document: 4000401-02 Blank Pattern.idw
Unspecified error (Exception from HRESULT: 0x80004005 (E_FAIL))
More Info:
System.Runtime.InteropServices.COMException (0x80004005): Unspecified error (Exception from HRESULT: 0x80004005 (E_FAIL))
at System.RuntimeType.ForwardCallToInvokeMember(String memberName, BindingFlags flags, Object target, Int32[] aWrapperTypes, MessageData& msgData)
at Inventor.FlatPattern.Edit()
at LmiRuleScript.Main()
at Autodesk.iLogic.Exec.AppDomExec.ExecRuleInAssembly(Assembly assem)
at iLogic.RuleEvalContainer.ExecRuleEval(String execRule).
View 1 Replies
View Related
Jul 19, 2013
I can't get Inventor to create a flat pattern of the attached sheetmetal part. It's a pretty basic part, just five folds. I'm not getting any error issues - when I go to the flat pattern it just shows the folded part (picture attached).
I assume it has something to do with the way I folded it and the notches, etc. Inv makes to accomplish the fold. I'm using Inventor 2013 on Win 8.
View 3 Replies
View Related
Dec 4, 2007
I have a cone shaped part and would like to put a hole in the curved face. I would like have to hole square to the face in the flat pattern so it can be cut on the plasma table, is there a way to do this? I attached the part with holes in the approximate location.
Windows 7 Pro 64
i7-980X
12Gb ram
GTX460
View 9 Replies
View Related
Oct 4, 2011
Is there a feature on the latest series of inventor whereby you can automatically generate fold detail on the flat pattern , ie. fold up 45 degrees, eliminating mistakes. I am currently on Inventor 2008 so this feature could be on a new version.
View 1 Replies
View Related
Sep 20, 2012
How to get this part into a usable flat pattern. I received the part originally as a stp file. I am running autodesk Inventor 2010.
View 9 Replies
View Related
Sep 12, 2013
I create custom sheetmetal styles from time to time via the API. It fails when the flat pattern has issues. Is there a way to determine if the flat pattern has errors/issues so I can delete it as required?
View 3 Replies
View Related
Sep 19, 2011
A colleague and I are working on a large assembly together, and we have received several .stp files from a customer (originally created in ProE), many of which are sheet metal that need to be unfolded and flat patterns made in drawings. The sheet metal default thickness has been changed to what the material thickness is. We have measured the edges on each side of and the radii of the bends, and they all appear to be consistently uniform. Yet, we get an error when trying to unfold or flatten the outer two bends. The customer sent us a flat pattern .stp file as well after letting them know we could not unfold the part, and there are many dimensions that we have to manually inserted to the drawing with the flat file because it does not have the bend information in it.
Is there something that we are missing to make this part unfold all the way?
In case my signature does not attach, I am running 2011 SP2, Windows7 Pro (SP1) 64-bit, 12GB RAM, Intel Xeon 3.07GHz, NVIDIA Quadro 2000
Inventor 2013 (SP2 Update 2), Windows 7 Professional (64-bit), SP1, Intel Xeon 3.07GHz CPU, 12GB RAM, NVIDIA Quadro 2000, Vault Basic 2013
View 4 Replies
View Related
May 30, 2012
I have a roll formed sheet metal part set to use a k factor of .5. The blank size should be (hand calculated) 7.924. Inventor is giving me 7.892. I made a new part with the exact same geometery as the first and set it to also use a .5 k factor, this one develops correctly to 7.924.
I checked all the dimensions multiple times. What am I missing here?
View 8 Replies
View Related
Feb 28, 2012
Is there a way to choose which flat pattern shows up on a Sheet Metal part where there are multiple rips?
Ex) a tank shell that is in quarters.
View 8 Replies
View Related
Jun 26, 2013
Is there a way I can tell Inventor which folds to fold or unfold when creating a flat pattern? I want to bend some C-Channel INWARD and Inventor doesn't seem to be able to do that. When it's formed C-Channel, I can bend the legs and all that but I don't want those legs to unfold when I create a flat pattern.
View 4 Replies
View Related
