I tried to add a custom avatar to my profile. The setup says to add an image to go to your "My Images" page (the link is on your profile page). I could not find the "My Images" page. I am attaching my avatar here.
View 9 Replies
I recently started to publish custom profiles in my Content Center.
What I wanted to do is to add a custom profile to content center and use it in frame generator. The problem is that I want to write in my Stock Number iProperty the Ordering number of the profile type and the generated length. I did everything in the content center publisher, but somehow it dosent work. It always writes my published file length. I can see that Inventor has the tools to do this, but somehow it dosen't work.
Inventor 2012
Win 7 64-bit
Dell Precision T5400
Intel Xeon 2,5 GHz
8 Gb RAM
NVIDIA Quadro Fx 3700
At my company we have a custom CC library with custom profiles for use in frage generator. We are having a problem with one of the frames. Everything goes well when the profiles is inserted.
But when I try to "trim to frame" the intersections of two profiles, it does not trim them correctly. It trims them in a 45 degree angle. As you can see on the attached jpg file.I tried everything. Checked the sketch, deleted the profile, republished the part.
I created a custom profile, IS34, and published it successfully as a structural shape for the frame gererator. My problem is I get an error when I try to use the notch command in frame generator between two of these frame members. I have tried creating a custom notch in the profile definition, but this did not work either. I expected one profile to counter-profile the other.
IS34 Profile
IS34 Frame
Error
I am using Inventor 2013.
I am experimenting with adding profiles to CC to be used in frame generator - how do I delete them?
In cc editor all delete buttons are grayed out.
Inventor creates a names to custom library parts based on settings and available parameters.
For all custom libraries I can create file names as I want except profile libraries.
The profile library create file name using Family Name + Stock Number and I did not find the
way to change it. I cannot get rid of that Stock Number in family name in this and other profile libraries. I wish I can use Part Number instead of Stock number in naming as more informative.
To change the file naming I do the following:
Manage - Editor - chose Library - chose family - Family Table - File Naming -
than chose required parameters to be shown as file name (for instance I have
{PARTNUMBER}), than in Map to Inventor Property: - Member.Display.Name
than OK - Refresh - Done.
All custom libraries obeys the file name changing EXCEPT the profile library.
[URL]
When I add a profile to Custom Centre to be used in a frame generator, in Base Qty by default it comes up as in, I want it Each. Where to change it?
View 1 Replies View RelatedHow do you add a custom working space profile to the profile list in CS6.
View 1 Replies View RelatedIs there a way to save a custom artboard setup with a custom document profile in illustrator cs5? I do technical illustrations and our page size is odd (7.19 x 8.96. It the size that our Framemaker layout is set to.). I have a custom document profile that I use, but I use the grids all the time so that my callouts are spaced out evenly around the art. I would like to have a way to set the artboard up so that the grid will align to the center of the artboard everytime I turn them on. Right now they always start from the top left and when I center art in the center of the page, the grid spacing isn't the same on each side of the art. I just want to be able to open my document profile, turn on my grids, have them start from the center, and I can get down to business. As it is now I have to go into my artboard settings and manually adjust the grid to the center. Small annoyance, but it still annoys me. I have tried to save it a few different ways, but nothing has worked. Maybe there just isn't a way.
View 4 Replies View RelatedAfter using Custom Profile for Frame Generator, the Part List will show total length, not individually. How to split these frame members?
View 2 Replies View RelatedI created an extruded aluminium profile (attached file: Item Profile 8 80x80) which I published into the Content Center. When using this profile in a frame design, and using the Trim To Frame command, the profiles are trimmed at a weird angle (attached pdf file).
View 2 Replies View RelatedAfter using Custom Profile for Frame Generator, the Part List will show total length, not individually. how to split these frame members?
Inventor Professional 2013 SP1.1
Windows 7 Pro 64-bit, SP1
HP EliteBook 8460w; 8 GB RAM; i7 - 2.0 GHz; AMD Firepro M3900 -1 GB
We loaded up C3D 2013 a month or so ago. I exported my user profile (Options>Profiles>Export) from C3D 2012 and loaded it into 2013. Now the profile will not stay loaded. I have to reload it every time I startup C3D. It also doesn't hold my view cube settings or my panes.
View 4 Replies View RelatedI am running Autocad mech 2009.
I would like to set up Autcad so that when it opens, it opens a custom profile.
In the past, I was able to accomplish this by using the autocad shortcut properties:
"C:Program FilesAutodeskACADM 2009acad.exe" /p <<customprofilehere>>
However, now....i have a shortcut that opens autocad up in xm mode and so the shortcut properties looks like this:
%SystemRoot%system32
undll32.exe %SystemRoot%system32VMCPropertyHandler.dll,Launc hVMSal "Windows XP Mode" "||4f5d99c9" "AutoCAD Mechanical 2009"
is there a way to modify this so that it will open the custom profile when it launches autocad in xmmode?
I have a client who has a customized workstation in 2012 and is trying to move to 2014. We have gotten most of it done but theyaretryingtoloadacustomlipsroutineanditkeepsfailing.
Image attached.
When inserting a content center part for which we have to choose a material, we would like to have a custom material as a default (material with name: "No material selected"). So when selecting no material for this part (for example when the user forgets to select a specific material), the default material (in this case material "No material selected") will be active. In this way, we can see in one view across the BOM which parts have no material assigned yet.
How can this be achieved in the content center (editor)?
Product Design Suite 2014
Inventor 2014, Vault 2014
HP Workstation Z220
Intel Xeon 3.4GHz
16GB RAM
Nvidia Quadro 4000
Windows 7 Professional (64bit)
When using Inventor with Vault, we have a problem when categorizing custom content center parts in Vault. In short, custom content center parts are incorrectly categorized as "Content Center" and automatically released - as there is no property that we can use to identify these files.
I need iLogic code to trigger when custom content center files are created/saved, wich adds the following custom iproperty "IsCustomContentCenter=True".
In my previous post of the same subject, I managed to create a door style using a custom made profile for the jamb .However I have been having a lot of problems trying to make the door leaf sit properly between the jambs. Attached is what I'm trying to achieve - is that possible in ACA? (BTW this was done in Revit)..
View 5 Replies View RelatedI am trying to create custom Materials in Inventor 2013. I have been able to create the custom appearances I want use on the materials and store them in the Inventor Materials Library.
After creating the custom appearance, Ive created new materials. When I try to change to new material appearance from default to my custom appearance, upon hitting the 'apply' button I get an error message which reads, 'failed to updated style'.
How do you go about saving a custom color profile in CS6? Gone is the save button after you have created the custom profile. In my case I want to save a custom Adobe RGB profile with a gamma of 1.0 instead of the usual 2.2. I can create it easy enough in the custom dialog box, but haven't figured out how to save it.
View 2 Replies View Related, I have CS5, and a Sigma 15 - 50 lens.
If I want to apply lens correction in ACR thgere is a dropdown list of lenses, but my lens isn't included. presumably because it has been superceded by the 12 - 24.
So, is it possible to create a custom profile for this lens and save it for future use? if so how do I do this?
I have a vintage macBook pro running Snow leopard, PS CS3 & DW CS3. I have a lenovo Business computer-Vista and a Dell-XP with PS 7. My monitor died and I bought a Dell U2412 which I calibrated with i1 Display 2, the grey scale was good & neutral on every 3rd gradation but wandered dramatically in between measured targets, the colour was either good for the skin and dull on the primary and secondary colour targets or over saturated on the skin and too red in the blues and mag (but with correct Sat on primary secondary). This monitor a good colour out of the box in reviews (but not on a mac, Dell profile loaded but no drivers for mac), so I tried it on the lenovo with a greyscale I made on the mac, the Phase One Lowres Colour Checker and a couple of profile targets I got from commercial labs close by (all had primary-secondary swatches greyscales and some natural examples). The greyscale was good very neutral (black grey meld together) and the skin colour and primaries were fine, this is viewing them in paint and windows photo gallery. Double checked them with the Dell, inside and out side PS they looked great using the Dell supplied profile and terrible with a custom profile by i1 Display 2!
I up graded to the i1 Display pro, on the mac the greyscale was very good all round, far better, the skin was good as were all targets but the blue (255 blue in PS is normally very deep 74% tone in the info pallet and very intense) is rendered, appears that is as a med cobalt blue with a visual tone of I would say no more that 50% and while a bright blue far from intense. The magenta is the same a soft pure pink. They measure as they should though 255 blue and 255 red and 255 blue for the mag. I installed and profiled the lenovo with exactly the same settings and it looked great all over! So a Mac PC issue? probably not the Dell exhibits the same behavior when using the i1 Display 2 profile and the Dell U2412 profile. I made a double swatch (blue and magenta) in PS to e-mail to myself so I can monitor the problem a little easier using all 3 computers, as I attached it to the e-mail and I see it looks great in mail, very strange. I loaded the image on a webpage and in DW and put it on my site, all browsers display it as PS does soft. IE on the lenovo displays it as it should. On the mac Preview also displays it correctly.
Recap:
The U2412 is capable of displaying the colours.
The custom profile is loaded as the system profile on the mac and the PC.
The mac displays the 2 colours correctly in Mail and Preview.
The mac does not display the colours correctly in PS DW or web browsers.
The profile is being used by PS; The greyscale is perfect, opening the display preferences window and changing profiles shows a difference.
The profiles are loaded but are changed or corrupted in certain applications.
I cannot be the only one to bring a macBook pro, Snow leopard PS and i1 Display Pro together, am I the only one with a problem?
How do I set up a custom document profile in Illustrator CC and save it for future use?
I do not see any way to save it.
In prior versions of PS, if I added a custom profile under Proof Setup, it would be pinned to the Proof Setup menu (along with the default profiles). That doesn't appear to happen in PS CS6.
Is there a specific place I need to save the custom Proof profiles to so that they will appear in the menu?
I have used X4 for about two years and X6 for the past couple of months. I cannot figure out how the create more rendering options under Share -> Create Video File. For example, if I want to use the MPEG codec but a custom resolution. Often custom is greyed out and not selectable. In free software such as ffmpeg or Virtual Dub I can create video as any resolution, aspect ratio, or codec. VS options seem to be very limited to these prepackaged choices. For example, some people have described moving a .DLL to the Coral folder to get custom codecs under the Create Video -> custom option. I'd rather not have to always render in VS and then recodec in another software.
My biggest challenge is the new Instagram format. It is basically 640x640 webm format. But I can import MPEG h264 without issue. My goal is to setup a 1:1 640x640 profile so I don't always have to game and stretch titles to display properly in the final version.
I'm using Lightroom 5 and Photoshop CS5. The problem is that if I apply a custom camera color profile created by X-Rite Passport Color Checker, I can no longer use an external editor, such as Photoshop, to edit my photos. Before I apply the custom profile, the external editor function works just fine. If I apply a custom profile in the Camera Calibration panel, then the ability to use external editors no longer works. There is no error message, but nothing happens when I try to edit in an external editor. If I go back and turn off the custom profile and go back to Adobe Standard, then the external editor function works again. What is going on? Is there a way to make it possible to apply a custom profile in Camera Calibration and still be able to use the external editors?
View 9 Replies View RelatedI have created custom profiles using Color Checker Passport for sunny, cloudy, flash, tungsten etc but would really like to create one for most shoots. I thought it would be a good idea to name it say "Temp" and overwrite each time so that I dont end up knee deep in camera profiles. But I am guessing if I do this will the latest saved version of "Temp" change the camera profile of all other previously saved versions of "Temp" from other shoots?It would be good if the saved version of "Temp" resided within the folder of that particular shoot only.
View 27 Replies View RelatedPhotoshop CS6 on Mac.
Edit an image file and get it to where I like on the monitor.Duplicate the file and set the new file to the profile for the printer which will be used, by using View > Proof Setup > Custom and setting an imported printer profile for the printing company that I use.
Edit the soft proof file to get it to where it looks good again. Save off the file for the printer and also save the new PSD file.
Close the PSD file.Reopen the new (soft proofed) PSD file.Still looks good, but.... when you check View > Proof Setup it's now generally set to Custom: U.S. Web Coated (SWOP) v2 instead of to the imported printer profile which was set previously. WHY???? Where did the printer profile go? Is it supposed to do this?
If I then reset View > Proof Setup to the correct printer profile, the image goes to crap again.
I have created default settings by serial number for my Canon Mark III 1ds which include enabled lens profile corrections. I then created a user preset with these default corrections. Next I imported a folder of RAW images shot with this same Canon camera with the user profile checked as part of the import. When I switch to the Develop module and check the Lens Corrections panel, I see that although it is checked for each file, the actual make, model and profile are not populated.
Is this a bug or am I overlooking something on import? I understand that in LR 4, you can apply specific lens and camera calibration profiles to camera serial numbers (noise reduction etc too).
MacPro 2.8 Ghz Quad-Core Intel Xeon with 16 gigs of ram running OSX 10.7.2.
Had a little fiddle with PS this morning, and came up with this .. nothing exciting I'm afraid.
Just wanted an XILE avatar, something to show who I am ... for the time being, until I can come up with something more extravagant like many of the ones.
how to make an avatar smaller that 16kb. When i go to cs2 and make a brand new file 60 x60 pixels it is allreay at 20 kb. Too large to post for an avatar. I know how to save with less quality but it still will not get any smaller.
View 1 Replies View Related
