I'm trying to create a dynamic block for a slotted hole, where I can specify and vary the width and length independatly.
To add complications, I also want the centrelines to stretch accordingly.
I've made some progress, it's 75% there, however certain combinations seem to 'break' the block.
ACad, MEP, 3DS Max
Windows 7x64
X5482 @3.2Ghz 8Gb Ram
Quadro FX1700
Dynamic block is for a title block which can be horizontal or vertical and a few different positions.
My lookup table controls the orientation and position of all the items including a number of attributes. But for two attributes I have allowed a grip on the Point Parameters so they can be dragged left/right if there is not enough room when the text is longer.
I can reposition the attributes but if I reposition twice then the Lookup table resets to its "Unmatched" configuration which I don't want. I believe I have to have an "unmatched" setting and "allow reverse lookup" and at the same time I want the user to be able to customize the position of these attributes.
I'am trying to create a block that has 3 components that can change
1- crane model or base
2- crane boom has different lengths and needs to rotate at pivot point
3- crane jib has different length and offsets from the crane boom
You can do this in one block or do you need to have 3 separate blocks and just piece together?
I've got a section marker (the letter designation with arrowheads pointing in the direction of the cut) that I cannot get to behave correctly.
When I set a parameter to one end with a move action, in order to have the arrowhead and attdef for the letter designation move upwards, all is well. When I try to do the same to the other end, the letter desingation attdef will not move.
Neither attdef is set to "Lock Position", so I'm puzzled why one works and the other end does not. I've tried a move action on both ends and a combination of move/stretch, but I can't get it to work.
Autocad Mechincal 2012 on Windows 7 64-bit
Is it possible to change the length of a line based on the length of an attribute?
I'd like to make the line a MINIMUM length of X" (I haven't decided how long yet--but know I'll need a minimum). But then after the user fills in the attribute, I'd like the length of the line to change to the length of the attribute plus a small amount (again, I haven't decided yet how much extra).
I was wondering if there is a way with DB's to have a line "follow" or "grow" with the content/value length of an attribute. Maybe some method of linking the attribute width to length of the line? Essentially, it would work just like turning on the underline setting when typing in mtext editor (or any program with an underline option for that matter), expect that the line could be placed anywhere, and would not have to reside directly below the text.
View 5 Replies View RelatedChange the 24 x 24 x 12 MLeader in this Block to Fields that read the length of the Lines that the Distance1 and Distance2 Parameters are attached to and tell me if it crashes? And if it does not crash, post a working DynBlk.
View 3 Replies View Related-you have a dynamic block with a grip that allows for any adjustable length.
-assume i need a the block to be 500mm long
-i stretch the block 500mm long in CAD (but it is still dynamic and will let me grip the length and adjust).
-after I insert it and set the 500mm length, can I somehow LOCK THE 500 LENGTH, so you cannot grip and edit the length anymore???? (but also have an unlock function for later)
This would be very useful in the following situation: Doing elevation view of a building with wall connections between floors....There would be MANY of these dynamic blocks....But they should all be the same length, per floor...But the next floor may have a different length....So I want to be able to Set Length > then lock in place... (and be able to unlock whichever I want, and adjust appropriately where the connection gets longer/shorter at another location...)
is there a way to associate a stretch action with the length of an attribute value (i.e. # of characters in the string) or is this something left to vlisp?
View 1 Replies View RelatedI created a dynamic block with text field that show the lenght of a line, but this line can be 0 and in that case I want that the text field will show nothing instead of "0".
I try to write it in diesel expression with if command but i don't know how to bring the object lenght into the diesel expression code.
in order to streamline some of my duties i wonder if theres a way to have a dynamic block not only that can change it's length and the dimension for that length (easy) but will also add features to the part. For example can one be made that when stretching its length that once it reaches a certain length automatically split into two sections and keep those 2 sections equal? Also can it be made to contain a tag that keeps track of the lengths as well as number of joints between sections multiplied by a constant?
View 1 Replies View RelatedI'm trying to create a pline in a dynamic block where the length is determined by two values I would input into properties or as attributes.
The first value 'A' will be a ground surface elevation
The second value 'B' will be a ground water elevation
I would like to the pline to have a length of A minus B.
I would then also like to have mtext (or any other method of display text) to display the values of A and B.
For example, if I have a ground surface of 102 and a ground water of 91, my line length will be 11, and I can display a label of '102' at the top of the line and '91' at the bottom of the line.
I've created dynamic blocks before, but none that have used an expression of two values or having to display inputted values. I'm not really sure where to start with this, or if it's even possible.
I am creating an upper cabinet which has a fixed height but you can select different widths. What our firm does is also list the size of the cabinet. What I would like to do is make this font some sort of preset attribute and control it with the visibility states. I also want to control the font height by the scale of the drawing. my question is I if its possible and how? I've attached what I have thus far. The attribute is in teh top right corner and is justified as top right. The only way I can get this to work is if I manually adjust the font after its inserted into the drawing.
View 5 Replies View RelatedWith using superelevation wizard in Civil 3d 2012, changing the lane width is not affecting the resulted values of transion length and run-off length, Is that correct ? ( as civil is using standerd AASHTO tables which assume that lane width typically is 3.6m )
Also, There is only 2 tables for 2-lanes and 4-lanes roadway, Is it for total road width or for one directon only, and what about different no. of lanes ?
I've made annotative blocks and I've made dynamic blocks... My intent is to integrate both but I can't find a way to move dynamic block parameters separately at different annotative scales.
In other words, if I insert an annotative dimension and add multiple scales I can move the dimension grips independently at each scale. If I insert a dynamic block I want to be able to use the dynamic block's action "grips" to do the same. However, with a dynamic block, if I move a stretch action at one annotation scale it moves the action at all annotation scales.
The attached file shows a simple example.
I have created a dynamic block with several visiblility states. The block works great for what I need it for. however, I am trying to add one more action to the block but am having issues.
This block is essentially a 24" retail cabinet with the visibility states showing the different drawer and shelf configurations. I want to be able to lengthen the cabinet in 24" increments and have the visibility show for each 24" section.....e.g. I want a 10' cabinet so I bring in the 24" starter block. Then stretch the cabinet to the 10' mark, then I can chose any drawer/shelve config for each 24" section (they are all different).
I can get the block to stretch in 24" sections....no problem.....i just want the visibility state to be duplicated as well for each section. Now as it stretches, there is only one Vis state and it only populates the first cabinet.
I could do this by copying the block over and over 5 times.....but I am hoping there is a way to make this dynamic.
I have a block I am making into a Dynamic Block. I will be adding in different visibility states. Depending on the visibility state the block would need to be inserted from a different point.
My question is, is it possible to add multiple insertion points to a dynamic block so depending on the visibility state it defaults to the correct insertion point?
is there a way to make dynamic blocks stretchable similar to a mleader,
the blocks i create are only stretchable by grips, and not by crossing
(i am using linear or point parameter stretches)
Is there anyway to link standard AutoCAD Grips and there commands to Dynamic Block Actions? I want to stretch an arc by its midpoint grip. This accomplishes something that no other commands do.
View 4 Replies View RelatedI am trying to draw 3D models for the first time, and something is confusing me. Sometimes when I draw a rectangle and it asks for a length width and height it seems the width means something else and the width means something else. I think the width means the distance from the z-axis on the XY plane, but then sometimes it is the distance from the Y-axis on teh XZ plane. I am just wondering if there is a good way to keep that a constant, or to remember which the length, width, and height is referring to at any given time.
View 9 Replies View RelatedWhy my AutoCAD now draws rectangles based upon coordinates and not by a given width and length as use to be?
View 4 Replies View RelatedI would like to determine the length, width, and height of a assembly.
Can i use the bounding box method to do this, or the range box?
I'm trying to change the size of a rectangle wall and I'm looking for "length" and "width" buttons in the properties manager box and can't figure it out. I thought I could just key in the new size after establishing an anchor point.
I've tried lengthen and extend. But the object is a closed polyline and what I'm doing is not working. Not having much luck with the key-grips either.
The wall is 47'2" and I want it to be 46' 8".
So I've done a reasonable amount of work with dynamic blocks. I have a block with a rotation action and grip to arbitrarily align it. However I realized when trying to combine it with an alignment grip (which actions on the basic or fundamental block rotation angle) that there didn't seem to be a way to some how link a dynamic block rotation action or one of the custom angle properties to a the fundamental block rotation angle. Thus there are two additive rotations at work; the dynamic block one with its grip and the fundamental rotation property.
This can cause some confusion when one person aligns with the grip and another via rotating the block's fundamental property and would also be problematic in the generalized sense if one was trying to select or programmatically read back the net angle alignment.
I have a dynamic block, that represents a stirrup.
I inserted in the block a Block Propreties Table, that have some preset dimensions for the stirrups. The grip of this table I decided to put in the top right corner.
The problem is that I can't make this grip moveable )
See the attachement with the block
new to dynamic blocks but looking to streamline my wiring diagrams here and have created a block that shows the typical wire styles we use in a simple easy way. I now want to add an overall flip to the entire block and have not been able to find set this. I would prefer to use the same label and go from there. I have included the block to show what I mean. It is only working on the single visible item at the one time. I know this has to be possible just let me know what I am doing wrong. I am running AutoCad LT 2013
View 3 Replies View RelatedI need to create a dynamic block for a "Glass Panel" in a balustrade. I need to be able to insert it, in one corner and stretch it in another corner, to suit the staircase angle.
I've created the block, but it isn't working correctly. I've attached a drawing, with the left hand drawing a sketch of how it needs to be. The right hand drawing is my dynamic block attempt. As can be seen, when the block is stretched between the 2 points, it doesn't follow the angle of the staircase correctly (Very slight run off)
I wish to create a dynamic block containing some attributes. These attributes are inside rectangles that can't be modified in length using linear parameters ; but the attribute has to be always in the middle of the rectangle. So, I draw a line inside the rectangle (in a hidden layer) and insert the attribute with center justification (not sure for the translation) that I place in the middle of this line ; then I put a coincidence constraint (not sure for the translation, but it's the first one) linking the middle of the line with the middle of the attribute.
But here's the problem : when stretching my rectangle, the insertion point of the attribute suddenly changes from "center" to "bottom left".
I am looking for a way to use the ATTIN/ATTOUT workflow to bring in data from an excel spreadsheet to drive the size of each of my block's instances. The block will be simple, a rectangle, with width and length parameters. For each entity in my excel/csv file these parameter values are spelled out. I know how to display these parameters in my attributes, but I don't know how, if I were to feed in these values, to drive the geometry. If there's a better way to take a list of width and length values to generate a series of blocks each with a rectangle containing its respective size.
View 1 Replies View RelatedI need to do some repetitive task on a lot of dynamic blocks, unfortunately, when I open each file, AutoCAD keeps asking if I want to open it with the block editor.
Is there a way to disable that dialog and open the files as normal dwgs?
A hint: BLOCKEDITLOCK doesn't make it, it shows another dialog...
usage of dynamic title blocks with visiblity states and defining page setup override templates which use same for quick plotting using sheet sets.
I have attached a simple dynamic block that I built which is the outter frame of our company title block, it is designed to allow users to quickly switch between Landscape and Portrait orientations.
The problem I am having is when I go to define page setups for my Sheet Set Page Setup Override Template I am unable to use the "Extents" option with auto-center because the "Extents", as defined by the page setup, includes ALL objects in the paper space regardless of visibility, so my title block ends up being centered in a stupid way if that printing configuration is used.
The only solution I have found is to use the "Layout" option when defining page setups, but this option produces other issues in other ways when printing. I don't want to use the "Window" option either for the potential for users to be using the page setup overrides to print drawings using different paper sizes or drawings that were not originally created using the current template the override is designed to accomodate.
Is there perhaps a system variable that defines whether invisible objects are included in the "Extents" setting in the page setup? I'm sure you'll all agree that Extents is the way to go in this situation, but it is not performing exactly as required.