For a surface: I would like to a boundary above a inlet point that is 3" deep.
I would like something like catchment area but the ability to specify a depth distance. Or specify a depth in the water shed analysis in the surface properties.
The only way I know to do what I want is user defined contours for each elevation. Is there a better way to do get a specific shed area for a depth?
I have two surface ( OG surface and Gravel LIFT ), i need to have a table that Show me Depths range between those two surface with a color range, in a table and also to be able to see it in the the top surface.
Basically, In every Spot of the surface, need to represent a Depth range between the OG and the gravel surface by a specific Color.
I can see the area of a TIN surface no worries (under Surface Properties/Statistics/Extended), but want I want to get is surface area of a TIN volume surface where no "extended" option seems to be available to view the area information with this type of surface.
View 8 Replies View RelatedI am trying to get C3D to report the surface area for a bounded area with no success. I am aware of the Bounded Volume feature, which BTW appears to be retired in the 2014 release (AECCCFDBADDBOUNDEDVOLUME fails to produce any results). Obviously there have been some major changes.
What I want to do is retrieve a report for a defined section of a surface, regardless, of what type of surface it is. I see this as simple as deriving the 3D areas of the trinangles within a bounds of a TIN.
I have a surface built for the bottom of a pond. The way to get the surface area (not the volume) of the bottom of this pond?
View 2 Replies View RelatedI have a large ex surface that I have divided into basins and such. I know need to evaluate the slopes in these areas. To do the whole surface at once seems to not be possible. Is there a way in c3d to view analysis information for a section of surface for instance in a polyline or fence?
View 3 Replies View RelatedI’d like to ask how I can measure the area of a region, defined on a TIN surface. ( i.e. the area of the bounded topographic terrain )
View 8 Replies View RelatedHow to calculate the AREA of cut and fill analogous to the volume of cut and fill between surfaces, but instead only between the alignment and the road profile in the prolfile view. From what I've read of similar posts a few people have had the same question but have been instructed how to do it with volumes as opposed to area. Also how to insert a table of cut and fill area analogous to the one you can inset from the volumes dashboard.
View 5 Replies View RelatedWhen I use the gradient tool in simple depth field in photoshop element 10 my whole image unblurs even when I chose a smal area to focus. It used to work well before but for one reason or another, it stopped. I uninstalled my program and that didn't fix the problem.
View 5 Replies View RelatedHow to changes the settings for the "Square Area" in mapcheck's closure summary. When I right-click the dwg name in the Settings tab of Toolspace and choose Edit Drawing Settings, then Ambient Settings, I see the Area settings, but in the closure summary, there is also "Square Area". Why are these both there? It WOULD be nice to show sq. ft. as well as acres, but I can't find anywhere to edit it.
Civil 3D 2012
Windows 7 Enterprise SP1
Dell Precision T3400
(Q9550 @ 2.83 GHz)
8GB RAM
Nvidia Quadro GTX 650 Ti BOOST
This is a Curve Plane which I need to get the area. I am using AutoCAD 2010, 3D..
View 9 Replies View RelatedI have a cast aluminum part I need to calculate the surface area for our plating process. I have done a simple area, its not right (.015ft^2). I have derived it as a surface but can't get a volume calculation.
View 9 Replies View RelatedI have contoured an irregularly shaped site that is required to be covered completely by a liner. Is it possible in autocad 2002 to get the area of the surface i have created?
View 1 Replies View RelatedWould be interested in a strategy for a varying depth overlay, i.e. where the overlay assembly follows a centerline design profile rather than a pavement depth up from existing grade. Then the trick would be for the software to calculate the asphalt volume between the new top surface and the existing roadway surface.
View 8 Replies View RelatedI want to calculate aurface area of iparts automatically. there are about 100 ipatrs and i want to find surface area of each ipart. is there any way that i just click the desired surface and its area is written in some file so that i can just go to the next ipart click the desired surface and its area is written automatically on some file.
Is there some option in inventor to define macro for it coz i hav no knowledge of defining macros.
How to calculate the three-dimensional surface area of a revolved arch (such as attached file) by autocad 2007? such as an irregular dome.
Which software can do the job? Autocad or Matlab software or .....
I have a road that I am engineering and have set up my subassemblies using the daylight standard. But i would like to force a cut section until the fill gets to 2'. so that when i have 2" of fill it will still cut my ditches.
View 2 Replies View RelatedIs there any subassembly can get variable slopes depend on depth like in Land desktop as you can see in the attached file.
View 2 Replies View RelatedI'm currently setting up a band set and want to include a band "pipe invert depth" i.e. basically trench depth.
There are properites in the band label style composer for "pipe invert level" and for "cover" and for "pipe diameter" but not pipe invert depth.Is there a way to display the pipe invert depth relative to the reference (design) surface/alignment?
A secondary question to this is can you use basic arithmetic in the band label style composer? eg pipe cover + pipe diameter?
I was wondering if it was possible in c3d to label points in the fashion often used for nautical charts in which each sounding (elevation) point is labeled with the integer component of the number followed by the decimal as a subscript. For instance 7.3 metres depth would look like: 73
Also I've seen charts with depths as fathoms and feet so 64 feet depth would be 104.
I want to make a subassembly in SAC 2013 to change the slope after require depth,see attached example.
View 5 Replies View RelatedI often have to do storm pond surfaces that (for the purposes of planning) are flat on the bottom. These surfaces are created from a combination of survey data and grading groups and the tin of these surfaces is perfectably acceptable. However, when contours are shown, the flat bottom is shown with contours jig-jagging all over the place.
The attached image shows a comparison of the same pond. The top was created with survey data and grading groups; the bottom was created using contour data only. The generated surface on the top shows the bottom contour going in different directions and has parts where the an expected contour is missing.
How to correct/manipulate the surface to show a proper flat surface?
Has instances where you set your tolerance for the maximum triangle lenth to say 50m to reduce the amount of triangles along the edge that run at long distances. When I do this I end up with multiple surface holes and I'm not sure why as there are points in the area.
I thought well maybe it's because i should've reduced my max triangles first then added breaklines. Would this matter? I also thought I could add a line to the surface to fix the holes vs. deleting surface lines along the entire edge of a surface for many many miles.
How to create a dome using just the surface area?
View 1 Replies View RelatedI have created a simple iPart that has three length variations, and therefor has three different surface areas.
I have added a simple table to my drawing. The table is linked to the iPart, I have used the column chooser to select the appropriate parameters to illustrate the length variations from the iPart. I would also like to include the surface area for each iPart member alongside each length variation in the table.
I want to calculate the total external surface area of the attached manifold. When I use the iProperties tool, it give me the surface area including internal surfaces of tubulars etc.
View 1 Replies View RelatedI am trying to add points into a surface. I have done this before without any problems, but now I am having issues.
When I ID points which makes up the surface it gives me the correct Z level e.g. 24.5m, however when I hover over the surface it shows me the surface name and a different z level e.g. 0.65m. What is the reason for this difference in z levels? I think this may be causing the issue I am having when I add new points.
I select the surface and use the 'edit surface command' in the ribbon, choosing add point.
When I add a point at the level I require(23.89m), it puts it in a lot higher than the surrounding area, so I tried to put the point in to the lower z levels (0.4m) it puts it in a lot lower!
My goal is coming up with the volume bounded by the design surface and the existing surface. I don't have the design surface modeled yet.
Do i need to create alignment offsets?. Alignment 1 profile view is also attached. Then Alignment2.
What about starting with alignment1 profile view? Since I have created a polyline as the design profile ?
how do I shrink labels? Where is it in the settings ; the Align folder had been check.
I am issues with DEM files that I am downloading from the USGS website.I download 24k, elevation for the area I need. I then choose staged 1 second, add a surface to a blank drawing, then upload the DEM files to the surface.
The surface imports correcty, but when I try to import points taken by a surveyor on the same drawing, they plot incorrectly.The DEM surface and the points from the surveyor do not correspond. Also, the DEM surface is in meters, not feet. I have tried changing drawing settings, datum types, coordinate types, etc.
Is there any way to change the referenced surface on a Surface Elevation Label. I can see the surface in the properties but cannot change it.
C3D 2011