I need to design a project but ı cant..ı have two profiles in use for one alignment..ı want to use left profile for left side, use right profile for right side.and ı want to draw cross section only one..how can ı design like this project..
View 8 RepliesI've got a highway project for which I'm modeling the corridor but the design profiles given to me are for the right lane top edge (ETW) and not the centerline (crown). This is an undivided planer roadway with a typical 2% cross-slope. How can I use that profile for the right edge to run my corridor? I can't seem to get the corridor to use the super table that is attached to the centerline when I use an offset assembly. Is an offset assembly the right way to go with this design?
What I've done just to get going is to take that right edge design profile and draw it in my centerline profile view, then lower it 0.24' (which is my 2% normal cross-slope for a 12' lane) and then use that as a centerline profile and let my normal super assembly and table data control the corridor through the supers. So far that is working--but is there a better way to do this?
My company had always used LDD until we were mandated to switch, our first project in Civil 3D is in the works. So far we have gotten through the beginning stages (alignments, profile, corridor, assemblies) but we are having a major issue with where to go from there. Right now I am trying to complete the design line work on the plan (wheelchair ramps, driveways transitions and signage) As of now I cannot get anything to line up easily with the corridor. I have been able to snap to the corridor so I can create a line at that exact spot to be correct, but then when I offset it will not change the elevation, I tried doing feature line and projecting the feature lines to the surface and some of it works but it becomes very buggy. My transition lines don't transition and some other lines I would expect to be at the same elevation have major grade changes. How to create the luinework at the correct elevation and with correct transisions along your corridor and surface?
View 2 Replies View RelatedI only get 2 choices when selecting corridor feature line to create profile - ETW_base, and ETW_sub. My Subassembly has 2 pavement sections, a base and subbase section. I need the top of pavement profile.
View 2 Replies View RelatedI created a profile view in order to create a corridor, I want the profile PVI stations to be on the same plane,
View 1 Replies View RelatedIs there any way to do that (workaround method).
View 3 Replies View RelatedFor an intersection, I am trying to create an alignment and profile from the Lane (edge of traveled way) of my main road for the intersection lanes to tie to. I just did this yesterday on this same corridor without any issue, but today it doesn't create the alignment correctly. It doesn't actually follow the feature line that I select. The alignment is in orange and the green line is the lane line. Notice that the alignment isn't following the lane line.
What would cause this? It worked fine doing the exact same thing yesterday, but today it's not.
Infrastructure Design Suite Premium 2014
Civil 3D 2014 x64
Windows 7 64-bit
6GB RAM
I've attach a profile of a corridor.
I don't know how to turnoff the assembly points .
I may send another inquiry after this it has to with corridor surface and boundaries.
I created a road centerline profile and corridor and then created a profile of the two curb lines from the corridor. The road profile that I made has a vertical curve in it but the curb profiles do not show that information, just grade breaks every 25 feet based on the corridor sampling distance.
I would like to have the vertical curve information on the curb profiles.
For some reason I cant seem to target an offset alignment layout profile with my corridor lane assembly. I can target the existing the existing groundprofile with the same offset alignment, but the layout profile when targetted does not change the lane in my cross sections. I can do this with civil 3d 2010, but not 2012. I have tried other lane sub-assemblies and it doesn't make a difference.
View 9 Replies View RelatedI'm trying to label the beginning and end points of a design profile (yellow line in the attached image) using the Horizontal Geometry Station Label tool. For some reason they will not show up.
View 1 Replies View RelatedWorking in Civil 3D 2014 SP1 I have a Design Profile that I have created by setting the Existing Profile to 'Static' and Creating a Copy of the Existing Profile... This leaves me with a Design Profile that follows the Existing Surface. The problem begins when I delete a section of PVI's and introduce new 'Design PVI's'... I have found that at apparently random times my Design PVI's have been lost and replaced with the original copied PVI's that follow the Existing Surface. This has occurred more than once and I can't find any reason as to why this may be occurring...?
Currently using Civil 3D 2013 & 2014 SP1
how to create a label style for design center of road (simple tangent) in profile that will work between multiple profile views. I've used the 'Create Multiple Views' profile view wizard. I use a horizontal dimension style label for CL road (looks just like an autocad linear dimension). I'd like the label work across separate views i.e. stop at view end, pick back up at view start.
The label I currently use is simply a line component from tangent start dimension to tangent end dimension and the text component is anchored to the line midpoint. Label looks as intended for normal use. For some reason the line drops as if looking for the actual pvi at the right side when i use multiple views.
It seems like I used to be able to do this in 2012.
I created a design profile and used the copy profile command. I close the layout toolbar of the original design profile.
When i select the copied design profile to grip edit a pvi, the existing ground profile and copied profile disappears and i cannot grip edit.
I have also tested this with an OOTB template.
Question: How to be able to grip edit a copied design profile in 2012.
I have a design profile and now I want to create one that's linked to it but have it 0.5m lower than the profile I just laid out. Is there a way to do this? I'd like to keep them dynamically linked so when i manipulate the 1st profile it will drop the 0.5m lower profile. In theory this would be a great feature to have in CIvil 3D.
At this point I will likely need to copy the profile and drop it 0.5m in elevation with edit geometry. Not ideal considering when I adjust the main profile I'll need to redo that process to show the profile 0.5m lower than my main design profile. (used as a side slope target).
I have an existing ground profile, and a design profile. All I want to do is label the slopes of the design. When I click my line label style and turn on the text it labels the existing ground and the design ground. I cannot find the setting in my two profile styles to turn the slopes off in the existing ground.
Oh, how can I get a tick on the V.C. dimension line?
We have recently installed Civil 3D 2014 Service Pack 1, and while for the most part it works great, we are noticing one significant issue with profiles. In particular, when we have a design profile actively selected with grips showing, and then select one of the grips, the PVI you are editing becomes offset from the cursor. When you select a point with the cursor, the profile syncs back up as you would expect.
Just thinking out loud, but it seems like it would be some sort of graphic card issue, but we are seeing it across multiple machines.
I have 2 different surfaces (Existing Ground & Proposed Pipe Invert) that I want to have the elevations shown for in a profile data band, but I want them to show at the design profile's PVIs (Proposed Road). Is it possible to set up a data band style that samples at one profile's geometry points but displays the elevations from these points from a different profile? My workaround is to set the data bands to all sample from the design profile first and label over the design profile's data band but I'm hoping for a cleaner solution. Attached is an image showing the profile view in question.
View 5 Replies View Relatedi have a long alignment going through a lot of creeks. right now the creeks are in xref just polylines but it intersect with alignments at areas.
is there a quick way to show all these lines on profile for design and drafting purposes? ideally want to just show a line at each intersection would be fine.
tried using pipes takes too long to set up. this is one important feature to have in the software.
i can program it again but i have not enough time to finish this project by mid october if i keep programming things.
Civil 3D 2012
Work: Xeon W3503, 12GB, Quadro 2000, Dell P2211H x 2
Home: 3930k, 12GB, GTX 590, U3011, QX2710
I have created a surface from a corridor. I set the boundary of the surface to the daylight of the corridor. In some areas of the corridor the surface does not triangulate see attached.
View 2 Replies View RelatedCopy a corridor successfully? I'd like to try this just a little worried about the explosion of evil this may cause to my Civil 3D session.
Even all the properties of the corridor setup from one to another would be useful. I'm building one corridor and an 2nd one that matches everything except I need to replace my Assembly with one meant for stripping.
My corridor surface is not matching my corridor top links. see attachments. this is affecting my volumes!
The section-plan(surface red).png is showing the section editor and the plan view. the red highlighted line in section is the corridor surface and as you can see in plan view the surface is incorrect and wiggly.
The pdf is all my sections with the red linework being the corridor surface.
C3D ver 2012
Win 7, 64bit
I have an alignment label that I normally use to show the PVI's of a profile in the plan view.
This is a little unusual, but in a specific case I wanted to design my profile at one alignment, but show it at another. I designed my swale profile in the pathway profile view and then superimposed the swale profile on the swale profile view. I then went back to the swale alignment to add these labels.
It's a no-go AFAICT. The only profile available for me to select for these labels is the original ground profile from the surface.
I'm working with a structure profile label style and it seems like the only way to anchor the position of the label is based on offsets from the structure itself... Any way to position the label based on the top of the profile view, so that I could make all of my labels horizontally aligned above the profile view?
View 9 Replies View RelatedIm creating a Profile Bandset and would like to have multiple surface/profile elevations shown, ie: EG, FG, Back of Curb and Back of walk. While creating this bandset I see that the text component editor properties only has code for profile 1 elevation and profile 2 elevation in the properties area, which the code for this looks like below.
<[Profile1 Elevation(Uft|P2|RN|Sn|OF|AP)]>
<[Profile2 Elevation(Uft|P3|RN|AP|Sn|OF)]>
Ive tried to write my own code using the profile 2 as an example but it doesnt seem to work as a 3rd surface/profile and only seems to mimic the profile 2 elevation when placed in the band
My questions are as follows
1) does Civil 3d only allow 2 surface elevations in any band set? if it does allow more profiles/surface elevations what am i missing to create it?
2) if Civil 3d does alow for multiple surfaces to be shown in the band set how do i get the text component editor to supply the extra profile elevation codes? or would i need to create from scratch
3) if i need to write the code from scratch does any listing of the codes and meanings of each code ie what does RN, Uft, Sn and so forth do and mean .
I have a group of profiles in a drawing and I want to change how one of the profiles is displayed through the profile view style manager, but I do not want to change how all of the profiles look. Is there a way to change the way a single profile looks without changing all of them?
View 2 Replies View RelatedI have a profile showing proposed storm sewer, existing sanitary, rock surface, existing surface, and proposed profile. Today for some reason the proposed profile and labels, and the existing surface are not showing on the profile and I'm not sure what has changed or how to get them back.
View 3 Replies View RelatedI am working C3D 2012. I have a proposed alignment and profile design by another firm that I had to tranfer into C3D. I had no problem getting the horizontal alignment to display from a text file. I tried to do the same with the profile by using the 'create a text file and create the profile from file' command. I got the POB, PI's, and POE to display. I then defined the VC. I wanted to verifiy that the profile was indeed accurate compared to what we were provided. So I tried to execute a profile report PVI Station and Curve Report - I keep getting an error that "No FG profiles in dwg".
I know the Proposed profile is indeed set to proposed in the properties. I have noticed that the icon next to the profile I create from the text file is different than the profiles created from scratch.
Is there a way to convert this profile to be recognized as a FG profile?
Intel Core i5-2500K CPU @ 3.30 GHz
8.00 GB
64-bit
I try to make curb return profile without profile view like a intersect command.
I was make curb return alignment but I can not find profile command without profile view.
The intersection wizard makes dynamic EOP profiles based off of the cross slope from the centerline. Well the intersection tool doesn't always work with funky intersection layouts. Is it possible to manually create a dynamic EOP profile based on the cross slope from the centerline profile?
Civil 3D 2012
Windows 7, 64 bit
I have a 10 foot profile view and a 15 foot manhole. I want to show the manhole but not the bottom 5 feet. It is extending beyond my profile view.
Civil 3D 2014 SP1
Windows 7 Professional
Intel Core Quad Q9650 3.0 GHz
8 GB, 64-bit