I have tried all of the expressions below to add the the vertical curve elevation at the pvi to my curve crest & sag labels on my profile and all I get is ??? for the value. I am currently running Civil 3D 2012.
IF({Grade In}<{Grade Out}, ({PVI Elevation}+{Tangent Offset at PVI}), ({PVI Elevation}-{Tangent Offset at PVI}))
{PVI Elevation}+{Tangent Offset at PVI}
{PVI Elevation}-{Tangent Offset at PVI}
I have tried all of the expressions below to add the the vertical curve elevation at the pvi to my curve crest & sag labels on my profile and all I get is? for the value. I am currently running Civil 3D 2012.
IF({Grade In}<{Grade Out}, ({PVI Elevation}+{Tangent Offset at PVI}), ({PVI Elevation}-{Tangent Offset at PVI}))
{PVI Elevation}+{Tangent Offset at PVI}
{PVI Elevation}-{Tangent Offset at PVI}
Need writing an expressions in a label style. I have part of it working, it is {Rim to Sump Height}-6 now I would like it to put 0 if it is 0 or less but I don't know how to do it. It works great on positive number but I want it to put 0 if it is a negative number.
View 8 Replies View RelatedOften we need to collect our topographic/boundary data using a state plane grid, but we still need to label property lines using the recoded deed bearings. We have a style with an expression set up to apply this rotation to lines and a similar one set up for curves. Is there a way to store this rotation and have both expressions look up the value from one place?
I am worried that I will type in the angle for the line labels and then forget to type it in for the curve labels, or maybe the angle is typed in correctly in one expression but incorrectly in the other. If it was typed in once, then even if it was wrong, at least the labels would be consistent and correct relative to each other.
To take civil 3D to the next level, is it possible to define a function in VBA and then use it in the label styles expressions?
Using Building Design Suite Ultimate 2014
I am trying to get my bearing label short name spaced to read with a "." after the N & E. Example: N. 00 00 00 E.
View 9 Replies View RelatedI'm trying to create an alignment label to display profile elevations at regular stations. Two questions:
1. I use an expression to set the text height. When I add a regular text component in the label this works fine, but when I add reference text I can't seem to use the expression as text height.
2. I want to use an expression to 'Truncate' the elevation, so that 178.35m displays as 78.35. I can't find a way to create an expression to do this (within the Alignment station labels).
C3D 2013. We have profile line labels, some of which get manually edited (for example, change the "<[Tangent grade(FP|P2|RN|AP|GC|UN|SD|OF)]>" to a static number such as 0.29%).
However, if you CTRL+Click and select one of these labels and change the style of that one label, then the manual edits are lost and the label reverts back to the default string.
Is there any way to turn this behavior off?
I'm trying to label my Profile label stations as raw stations, 20~20 meters, and I'm not being able to adapt the format to STATION 0, STATION 2, without any plus zeros or +, or -, or commas, or anything, as following in the image.
Is there a easy way to do it?
I have an alignment label that I normally use to show the PVI's of a profile in the plan view.
This is a little unusual, but in a specific case I wanted to design my profile at one alignment, but show it at another. I designed my swale profile in the pathway profile view and then superimposed the swale profile on the swale profile view. I then went back to the swale alignment to add these labels.
It's a no-go AFAICT. The only profile available for me to select for these labels is the original ground profile from the surface.
I'm working with a structure profile label style and it seems like the only way to anchor the position of the label is based on offsets from the structure itself... Any way to position the label based on the top of the profile view, so that I could make all of my labels horizontally aligned above the profile view?
View 9 Replies View Relatedhow to label a curve by points in C3D? I'm finding half of the new "fix" (line by points).
C3D - 2014, Sincpac Addon
My curve labels keep skipping. Why do they keep skipping from C6 to C9? I know how to use the renumber tags command. It just keeps skipping C7 and C8 for no apparent reason. There are no tags on frozen or off layers. When I add all possible objects to my curve table it does not change.
Windows 7 x 64 bit
NVidia Quadro 2000 Dual Monitor
6.00 GB RAM
Intel Xeon W3550 @ 3.07 GHz
Civil 3D 2013 SP 2, Civil 3D 2012 SP2, Civil 3D 2011 V3, Civil 3D 2010 V3
How to label the curve with its degree of curvature (Da)?
Degree of curvature (Da) can be calculated based on two different ways
Arc definition (considering 30 meters arc length):
Da=1719.74/R
Chord definition (considering 30 meters chord length):
Da=ASIN(50/Radius)*2
The issue here is that there is not built in option to label the curve with its degree of curvature.
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
handle a PRVC label? Right now I have the PVC and PVT labels on top of each other. Is there a nice solutioon other than making a new label style?
Dell Studio XPS 9100
Intel Core i7 CPU 930 @ 2.8GHz
12GB Ram
64 bit
C3D 2012 SP3.0
I have an alignment that is line and curve tagged for a table. The last segment of the alignment is a 3 point curve. It shows up in the alignment grid view, and is tagged. When the table is produced the everthing comes in except the 3 point curve I mentioned.
View 1 Replies View RelatedI need to lable the delta of a PI in an alignment where one segment is an arc and the following is a non-tangent line.
Geometry points don't offer delta and Tangent Intersections won't label at PCs and PTs.
Is there an expression that can be used?
I am having an issue with my label displaying in my profile after I create my plan and profile sheet set. The PVC, PVI and PVT all show up, but the labels are not displaying. I looked through the layers and they are all thawed.
View 7 Replies View RelatedWe are upgrading from LDD2008 to Civil3D 2013. I'm working on a Civil3D template
I'm setting up line and curve label style. Oringally we were going to have one set of line label style. Ex. Bearing Above or Bearing Below. After seeing that the line labels does not look at the current text style we decided to make copies of the original label styles based on Text Styles.So now I have Bearing Above60, Bearing Above100, etc. I named them based on the Leroy styles and sizes.
After editing each one and changing the Text Style each one looks at, it is not using the Texting Style i assign it. I'm doing this in the General Tab and Text Style for each label style.
i guess I should have tested before creating all them to find out it didn't work.Does it need to be done somewhere else or is do I have to do something with the overall label style overrides?
I want to make a curve label with all its elements (radius,tangent...) and the data of widenning and superelevation on the curve?. I attached the label that I want to create on C3D.
C3D 2012
Win-64 bits
I'm using civil 3d 2008 and trying to lable my pavement radius with Line and Curve Label but the delta setting is only in decimal, how do i get it to read degrees, minutes and seconds.
View 4 Replies View RelatedI am using Civil 3D 2009 version 4.
I have designed a railroad yard that the construction plans require all grading to be to centerline of rail (0.5 feet under the ties) and my profiles are required to be to the top of rail (1.3 feet above the centerline elevation). Since I already have the grading surface done I was hoping there was a way to target my grading surface and add the 1.3 feet to the elevation in the label. Is that passable?
Using the stock 'Elevations and Stations' style I targeted the existing ground for profile 1 and the finished ground for profile 2. Then I tried using the language you enter at the command line to do math in the label (+ 1.3 <[Profile2 Elevation(Uft|P2|RN|AP|Sn|OF)]>) but that only generated a label that read "(+ 1.3 242.00)" instead of the "243.30" that I need for the loading area, for example.
AutoCAD Civil 3D 2012 (Primary), 2011 by contract.
Dell Percision T3500: MS Windows 7 64-bit SP1; Intel Xeon CPU W3505 @ 2.53GHz, 12.00 GB RAM, NVIDIA Quadro 600
Is there a way to insert a jog into a profile label?
View 9 Replies View RelatedSeems like a bug on Autocad Civil 3D 2013. I followed all the tutorials to design a circular vertical curve on a profile and it just dont work. I put circular on settings, click on circular curve by PVI button, the software even ask the radius and it end up designing a parabolic curve.
View 2 Replies View RelatedI just created a profile by choosing my PVIs and linking them together with tangent curves. How do I add labels to show the vertical curve properties (K value, curve length, station of PVI, elevation of PVI...)? I'm guessing I have to edit the label style?
View 2 Replies View RelatedI'm using Civil 3d 2010, in profile curve details are coming worng, PVI station is OK but LOW PT station of curve is wrong, also in Civil 3d 2009 no any curve details are coming. I'm sending the secreen shot of profile.
View 1 Replies View RelatedI am working on a corridor. I have a proposal profile, and now i wanted to add a vertial curve between the new profile and exsiting. (see attached.) but i have not done before.
View 4 Replies View RelatedI'm trying to label the beginning and end points of a design profile (yellow line in the attached image) using the Horizontal Geometry Station Label tool. For some reason they will not show up.
View 1 Replies View RelatedI would like to add a wipeout to this structure label so I don't see the profile view grid lines. I want the wipeout to be the exact width and height of the label. I have tried numerous edits but can't seem to get it. What is the easiest/best way to add this wipeout?
View 9 Replies View RelatedI need to know how to display a proposed profile elevation in the major station alignment label, I mean, for example, I want to read in the label "0+000, 494.444". I've already edited my major station label style adding a (profile type) Reference text, and it only displays "?". I suppose I need to associate it with the correct profile, but I've not figured out how to. I show you how the label looks in the attached image.
View 8 Replies View RelatedI am trying to create a label for fire hydrants in plan view that shows the flange elevation. I want the elevation to be 0.4' above the adjacent road profile. I added a reference text component to my label style that shows the profile elevation. Where would I find the expression for the profile elevation reference text?
Civil 3D 2012 SP3 | Win 7 64-bit SP1
Xeon E5-1620 @ 3.60GHz, 16GB Ram | NVidia Quadro 600