AutoCAD Civil 3D :: Find Path Of Determined Slope Along A Surface?
Oct 25, 2013
I am trying to draw an alignment for a road. I want the alignment to represent the outside of the curve as the road climbs up and around a mound. Is there not way to do this in Civil 3D?
[URL]
and now I am thinking I will have to do this manually, extract contours, and trim/extend my way to victory...I really would like to have this in a dynamic situation so I can make adjustments. Also, it would be adventageous to have the line actually follow the grade so I dont have to add curves in etc later...
View 3 Replies
ADVERTISEMENT
Nov 7, 2012
in my link "link slope to surface", i have the slope set to -2.00%. in the cross sections, it is at a +2.00%. why is this thing not linking at the defined -2%? see image.
View 1 Replies
View Related
Apr 5, 2013
Please find the attached picture. It shows a surface with its data points. I extended the surface to the outer boarder shown by kriging. The slope of the surface that was added with the extension (past the data points) has an upward slope that was generated. I need the surface to stay level with the data points that are there.
How to avoid that added slope when extending a surface?
View 7 Replies
View Related
Apr 18, 2012
I'm modeling a simple corridor (12' lane 2%, 6' shoulder 6%, 4:1 to match EG). I used the "LinkSlopeToSurface" subassembly for the 4:1 to match the EG. Unfortunately our EG isn't always wide enough for the 4:1 slope to match it somewhere.
Is there an assembly that would use 4:1 as a standard daylight slope, but where necessary adjust the slope, max. 3.5:1, to match EG surface?
View 5 Replies
View Related
Aug 16, 2013
I am using AutoCAD Civil 3D to do a slope analysis across project locations. When defining slope categories, I am finding that the max slope percentages are astronomically high; ranges are being returned up to 360,000%--and I've only done three regions! I understand vertical slope but these percentages are not realistic by any means, especially through the areas in which I am working.
A specific example: between a contour at elevation of 792 ft and a contour at elevation of 794 ft at a distance of approximately 60 feet, the slope percentage being returned is in the 9000% range. There is not a sudden drop or rapid change in elevation between these two contour intervals to provide reason for this high of a percentage. I would expect to have a slope percentage nearer the 3% range.
The data source of the contour information is LiDAR being brought into CAD via the task-based geospatial option using MapImport. All data tables are being kept. Polygons are being imported as closed polygons. There are no surface errors being reported upon creation. The project locations were created in another program and imported into CAD using the same manner. The only thing that I can conjure up is that there is some sort setting issue.
View 4 Replies
View Related
Sep 17, 2013
I change my surface style to slope banding (3 ranges) and make a legend table.All of the three ranges in the table are red and my surface ranges are blue, yellow, & red.
View 9 Replies
View Related
Jun 27, 2013
i was wondering is it possible to show slopes or grades on my surfaces , or corridors IN PLAN VIEW ?
View 8 Replies
View Related
Dec 30, 2013
I am trying to create grading slope from a Feature line that was created at a constant elevation of 609m. I want to create a slope of 3:1 from the feature line to a surface I created. I recall in AutoCAD Civil 3D 2011 that you could create a slope directly to a surface. Is there a way of doing that in 2014 or did I simply forget a step when I created my Grading Groups?
I created the grading group using the Grading Creation Tool Pallet and selecting Set Grading Group. Then I set my target surface to the one I want to grade towards. I thought all I had to do than was go to Create Grading select the direction of grading and the slope. I thought the slope would continue to the target surface but it asked for a distance for grade that would throw off any volumes I want to pull off.
Did I have to create a new surface for my Pad at 609m than grade from that and how would I make sure my slope continues till it contacting the surface I want to target?
View 2 Replies
View Related
Apr 3, 2012
Am I correct in assuming that if Surface Labels by One Point is chosen, the slope as shown is the maximum slope of the surface triangle where the point was chosen??
IDSP Premium 2014 (mainly Civil 3D 2014 UKIE SP1 & Infraworks with some limited 3ds Max Design)
Win 7 Pro x64, 256Gb SSD, 300Gb 15,000 rpm HDD
16Gb Ram Intel Xeon CPU E5-1607 0 @ 3.00GHz (4 CPUs), ~3.0GHz
NVIDIA Quadro 4000, Dual 27" Monitor, Dell T3600
View 2 Replies
View Related
May 13, 2013
I have surface percent slopes labels in my drawing. I want to change the current style precision to only one decimal not three and I don't want to see the negative in front of the slope value.
View 1 Replies
View Related
Dec 12, 2013
On my corridor I am using Link Slope to Surface, using a 3:1 slope. But it is giving me a 3:1 slope radial to the corridor - what I really need is a 3:1 slope between the contours themselves. On the inside of a tight curve, this makes a big difference. See the attached screenshot. Is there a workaround for this?
View 9 Replies
View Related
Nov 21, 2013
I am re-routing a small stream. I am using generic links for the bed and side slope. I whant the side slope to be 3:1 and project beyond the existing culvert wall in the eg model. can this be done easily?
HP Z210 Workstation
Intel Xeon CPU E31240 @ 3.30 Hz
12 GB Ram
View 2 Replies
View Related
Nov 5, 2012
I have a drawing like as attached drawing. I must to model 2 flat surface with different elevation and a slope between them.
View 5 Replies
View Related
May 26, 2010
I'm just trying to figure out how to label my surface with slope values in Degrees. The existing options are rise/run, percent...
View 4 Replies
View Related
Apr 4, 2012
I have a polyline defining a proposd wind farm access track and I have offset it 10m each side. I have then dreated a slope label between the southernmost end points which gives the existing ground slope at right angles to the centreline. I created the Array (as shown in arrayed.jpg) and it looked good but after hitting enter there were only three labels (after enter.jpg)
I did a rectangular array of slope labels with no problem at all so what's wrong with the way I'm doing the path??
IDSP Premium 2014 (mainly Civil 3D 2014 UKIE SP1 & Infraworks with some limited 3ds Max Design)
Win 7 Pro x64, 256Gb SSD, 300Gb 15,000 rpm HDD
16Gb Ram Intel Xeon CPU E5-1607 0 @ 3.00GHz (4 CPUs), ~3.0GHz
NVIDIA Quadro 4000, Dual 27" Monitor, Dell T3600
View 3 Replies
View Related
Jan 22, 2012
Using Civil 3d 2012, I have a slope label with mult lines, and set to plan read.
When I rotate the label, the goes to plan read, but the bottom line text is on the top, top on the bottom.
I hope it would be simular to mirror.
I look at the expression, but didn't see any way to get the label angles.
View 6 Replies
View Related
Nov 20, 2012
From the subject is there any way to apply Link slope to surface with maximum width
View 1 Replies
View Related
Aug 4, 2012
I am having trouble getting my assembly to work in my corridor. I have a Basic Lane Transition subassembly with a Link Slope to Surface subassembly attached to it. The assembly follows my centerline alignment and the lane widens as designed out to my offset alignments. The slope grading to daylight works fine until the transitional lane starts to widen, then the slope assembly stays at the same point on the lane and does not stay linked to the end of the lane.
I am also having trouble getting the subassemblies to attach to the proper points. I keep trying different OSnaps unitl one seems to work, but I am never sure the subassemblies are connected properly.
View 9 Replies
View Related
May 26, 2012
I am grading a parking lot and trying to highlight areas with less than 1% slope.
I can't find the spot to set user slope ranges in the setting tab.
I can find setting number of ranges with three options of minimal use.
This used to be so simple in LDD.
The examples I have seen for this function all show odd ranges of limited value.
View 7 Replies
View Related
Sep 24, 2013
I'm trying to suppress trailing zeros in a surface slope label in run:rise format. Basically, if it's a 2 to 1 slope, I want it to read 2:1 or if it's a 2.5 to 1 to read as 2.5:1.
I found this blog showing how to do it for line slopes, but I think it's not able to work using the run:rise format.
View 1 Replies
View Related
May 25, 2013
I use Civil 3D 2011 and I am new to it. I have created a natural ground surface from survey points. Now i want to create a finished surface with a specific slope in a specific direction at a specific elevation and then to calculate cut and fill volume.
I can create a flat surface at a specific elevation. How to tilt this surface to a specific slope along a specific direction.
View 9 Replies
View Related
Jun 12, 2013
I am looking for grading utility in autocad civil 3d. So, i need to smooth my projection slope to target the surface without projection steps. The objective is to correct a surface to implant photovoltaic structures.
View 3 Replies
View Related
Dec 27, 2013
I am trying to create a surface rise:run slope label for our company template file. I have it set using the default values that I want. But right now the text is just 1:1...where we want it to read 1V:1H.
how I can keep the label dynamic to the surface, but put the V & H in the label after the values.?
View 2 Replies
View Related
Aug 20, 2012
Can you not perform a slope-slope intercept to place a PVI? Essentially holding the sta and elev of the PVI's directly before and after the PVI of interest and changing the grade in and out so that the sta and elev of the PVI of interest are changed.
View 2 Replies
View Related
Mar 22, 2011
Can't figure out how to match gutter slope to outside lane super subassembly slope. Have super eop targeting a feature line with elevations, but when i check section editor gutter slope doesn't match pavement slope.
Civil3D 2013
Windows 7, 64 bit
Intel i7 2600 @ 3.40Ghz
16 GB RAM
Nvidia Quadro 600
View 9 Replies
View Related
Jan 22, 2013
i need a shoulder subassembly that varies slope in relation to the lane superelevation slope. i know that i can get a subassembly for the shoulder that will follow the alignment superelevation xml data but in my case i can't use it because we are just adding a shoulder to an existing road. we're not changing the superelevation of the existing road, just milling and overlaying and widening. right now i've created a profile of the outside edge of the shoulder that gives me the correct shoulder slope but whenever i change my centerline profile i have to redo the shoulder profiles which is a real time suck.
View 9 Replies
View Related
Aug 13, 2012
I am in the process of transitioning from land desktop to Civil 3D. I design roads in steep terrain and sometimes need to have my catch (daylight) slopes change. So my question is, how do I change a daylight slope at a specified depth? For example, from the shoulder of the road I want a 3:1 fill slope to a depth of 10 feet than change to a 2:1 slope until it catches the existing surface. Can this be built into a subassembly such that if the fill is less than 10 feet it will daylight correctly at a 3:1 and if the depth is greater than 10 feet then it carries the 3:1 for 10 vertical feet and then changes to the 2:1 until it daylights?
View 9 Replies
View Related
Feb 2, 2012
I want to draw a line from the center of this sphere to where the sphere and TIN interesct
View 9 Replies
View Related
Aug 1, 2012
If I use this code it will give me the insertion point for a block
(setq ent (car (entsel "
Select Main Object: ")))
(setq InsPt (assoc 10 (entget Ent)))
Now if I try to use this for a surface label and try to get the insertion point
(setq ent (car (entsel "
Select Main Object: ")))
(setq oEnt (vlax-Ename->Vla-Object ent))
(vlax-dump-object oEnt)
I dont see anything that will get the insertion point.
View 1 Replies
View Related
Jan 11, 2012
I am evaluating volumes of concrete removed from a surface and the volumes of concrete poured to replace the demolished concrete.I have created surfaces for each stage of the process in individual drawings.
I have created a drawing for the section views and successfully created cross-sections showing all the surfaces.When I compute materials, determining cut material between 2 of the surfaces, the end area is not always determined at every station.
I have previously noticed end area "shapes" with breaks in them. Each time, this was because there was a void in the surface triangulation.Is there any way that I can interrogate a surface to check whether the triangulation is incomplete, with voids in it?
I posted last week and included the attached screen print showing incomplete triangulation which I only noticed by turning on the "Shades of Gray" visual style.There must be some way to check surfaces without having to use the memory gobbling visual style.
View 9 Replies
View Related
Jul 1, 2013
The undefined areas of a slope map now have a hatch to them and are plotting black. This map was created a month ago in 2012 without issues, upgraded to 2014 and now the undefined range has hatch!
View 8 Replies
View Related
