AutoCAD Civil 3D :: Link Slope To Surface
Nov 7, 2012in my link "link slope to surface", i have the slope set to -2.00%. in the cross sections, it is at a +2.00%. why is this thing not linking at the defined -2%? see image.
View 1 Replies
ADVERTISEMENT
AutoCAD Civil 3D :: Link Slope To Surface Projection?
Nov 21, 2013I am re-routing a small stream. I am using generic links for the bed and side slope. I whant the side slope to be 3:1 and project beyond the existing culvert wall in the eg model. can this be done easily?
HP Z210 Workstation
Intel Xeon CPU E31240 @ 3.30 Hz
12 GB Ram
AutoCAD Civil 3D :: Link Slope To Surface With Maximum Width
Nov 20, 2012From the subject is there any way to apply Link slope to surface with maximum width
View 1 Replies View RelatedAutoCAD Civil 3D :: Transitional Lanes And Link Slope To Surface
Aug 4, 2012I am having trouble getting my assembly to work in my corridor. I have a Basic Lane Transition subassembly with a Link Slope to Surface subassembly attached to it. The assembly follows my centerline alignment and the lane widens as designed out to my offset alignments. The slope grading to daylight works fine until the transitional lane starts to widen, then the slope assembly stays at the same point on the lane and does not stay linked to the end of the lane.
I am also having trouble getting the subassemblies to attach to the proper points. I keep trying different OSnaps unitl one seems to work, but I am never sure the subassemblies are connected properly.
AutoCAD Civil 3D :: How To Use A Generic Link Slope
Dec 4, 2013I haven't had to use a generic link slope in a while, but I'm baffled as to why this isn't working for me. Below is my assembly which looks looks fine, but the corridor is doing the opposite of what it should be doing.
And here is what the corridor is doing.
My grass strip link is going in the opposite direction and it's much longer than 7 feet. Am I missing something or is this another bug?
Infrastructure Design Suite Premium 2014
Civil 3D 2014 x64
Windows 7 64-bit
6GB RAM
AutoCAD Civil 3D :: Subassembly Composer - Link Slope To Elevation
Oct 8, 2012Its a embankment crest (dam wall) and then sloping down at an angle to a target elevation. I want it to shoot through my topo / surface and then apply a boundary later.
It looks fine in Composer but doesn't show up in C3D - only straight line. Would like the same outcome as the Generic Link Code - LinkSlopetoElevation.
AutoCAD Civil 3D :: Slope Of Surface After Kriging
Apr 5, 2013Please find the attached picture. It shows a surface with its data points. I extended the surface to the outer boarder shown by kriging. The slope of the surface that was added with the extension (past the data points) has an upward slope that was generated. I need the surface to stay level with the data points that are there.
How to avoid that added slope when extending a surface?
AutoCAD Civil 3D :: Daylight To Surface Max Slope?
Apr 18, 2012I'm modeling a simple corridor (12' lane 2%, 6' shoulder 6%, 4:1 to match EG). I used the "LinkSlopeToSurface" subassembly for the 4:1 to match the EG. Unfortunately our EG isn't always wide enough for the 4:1 slope to match it somewhere.
Is there an assembly that would use 4:1 as a standard daylight slope, but where necessary adjust the slope, max. 3.5:1, to match EG surface?
AutoCAD Civil 3D :: Slope Surface Percentages
Aug 16, 2013I am using AutoCAD Civil 3D to do a slope analysis across project locations. When defining slope categories, I am finding that the max slope percentages are astronomically high; ranges are being returned up to 360,000%--and I've only done three regions! I understand vertical slope but these percentages are not realistic by any means, especially through the areas in which I am working.
A specific example: between a contour at elevation of 792 ft and a contour at elevation of 794 ft at a distance of approximately 60 feet, the slope percentage being returned is in the 9000% range. There is not a sudden drop or rapid change in elevation between these two contour intervals to provide reason for this high of a percentage. I would expect to have a slope percentage nearer the 3% range.
The data source of the contour information is LiDAR being brought into CAD via the task-based geospatial option using MapImport. All data tables are being kept. Polygons are being imported as closed polygons. There are no surface errors being reported upon creation. The project locations were created in another program and imported into CAD using the same manner. The only thing that I can conjure up is that there is some sort setting issue.
AutoCAD Civil 3D :: Surface Slope Table Colors
Sep 17, 2013I change my surface style to slope banding (3 ranges) and make a legend table.All of the three ranges in the table are red and my surface ranges are blue, yellow, & red.
View 9 Replies View RelatedAutoCAD Civil 3D :: Show Slope / Grade On Surface?
Jun 27, 2013i was wondering is it possible to show slopes or grades on my surfaces , or corridors IN PLAN VIEW ?
View 8 Replies View RelatedAutoCAD Civil 3D :: Creating Grading To Surface With Slope?
Dec 30, 2013I am trying to create grading slope from a Feature line that was created at a constant elevation of 609m. I want to create a slope of 3:1 from the feature line to a surface I created. I recall in AutoCAD Civil 3D 2011 that you could create a slope directly to a surface. Is there a way of doing that in 2014 or did I simply forget a step when I created my Grading Groups?
I created the grading group using the Grading Creation Tool Pallet and selecting Set Grading Group. Then I set my target surface to the one I want to grade towards. I thought all I had to do than was go to Create Grading select the direction of grading and the slope. I thought the slope would continue to the target surface but it asked for a distance for grade that would throw off any volumes I want to pull off.
Did I have to create a new surface for my Pad at 609m than grade from that and how would I make sure my slope continues till it contacting the surface I want to target?
AutoCAD Civil 3D :: Surface Slope Label One Point
Apr 3, 2012Am I correct in assuming that if Surface Labels by One Point is chosen, the slope as shown is the maximum slope of the surface triangle where the point was chosen??
IDSP Premium 2014 (mainly Civil 3D 2014 UKIE SP1 & Infraworks with some limited 3ds Max Design)
Win 7 Pro x64, 256Gb SSD, 300Gb 15,000 rpm HDD
16Gb Ram Intel Xeon CPU E5-1607 0 @ 3.00GHz (4 CPUs), ~3.0GHz
NVIDIA Quadro 4000, Dual 27" Monitor, Dell T3600
AutoCAD Civil 3D :: Surface Percent Slope Labels
May 13, 2013I have surface percent slopes labels in my drawing. I want to change the current style precision to only one decimal not three and I don't want to see the negative in front of the slope value.
View 1 Replies View RelatedAutoCAD Civil 3D :: Corridor Grading - Slope To Surface
Dec 12, 2013On my corridor I am using Link Slope to Surface, using a 3:1 slope. But it is giving me a 3:1 slope radial to the corridor - what I really need is a 3:1 slope between the contours themselves. On the inside of a tight curve, this makes a big difference. See the attached screenshot. Is there a workaround for this?
View 9 Replies View RelatedAutoCAD Civil 3D :: How To Model 2 Flat Surface And A Slope Between Them
Nov 5, 2012I have a drawing like as attached drawing. I must to model 2 flat surface with different elevation and a slope between them.
View 5 Replies View RelatedAutoCAD Civil 3D :: Surface Labels - Slope In Degrees
May 26, 2010I'm just trying to figure out how to label my surface with slope values in Degrees. The existing options are rise/run, percent...
View 4 Replies View RelatedAutoCAD Civil 3D :: Find Path Of Determined Slope Along A Surface?
Oct 25, 2013I am trying to draw an alignment for a road. I want the alignment to represent the outside of the curve as the road climbs up and around a mound. Is there not way to do this in Civil 3D?
[URL]
and now I am thinking I will have to do this manually, extract contours, and trim/extend my way to victory...I really would like to have this in a dynamic situation so I can make adjustments. Also, it would be adventageous to have the line actually follow the grade so I dont have to add curves in etc later...
AutoCAD Civil 3D :: Surface Slope Style Plan Read?
Jan 22, 2012Using Civil 3d 2012, I have a slope label with mult lines, and set to plan read.
When I rotate the label, the goes to plan read, but the bottom line text is on the top, top on the bottom.
I hope it would be simular to mirror.
I look at the expression, but didn't see any way to get the label angles.
AutoCAD Civil 3D :: 2012 Surface Style Set User Slope Ranges
May 26, 2012I am grading a parking lot and trying to highlight areas with less than 1% slope.
I can't find the spot to set user slope ranges in the setting tab.
I can find setting number of ranges with three options of minimal use.
This used to be so simple in LDD.
The examples I have seen for this function all show odd ranges of limited value.
AutoCAD Civil 3D :: Suppress Trailing Zeros In Surface Slope Label
Sep 24, 2013I'm trying to suppress trailing zeros in a surface slope label in run:rise format. Basically, if it's a 2 to 1 slope, I want it to read 2:1 or if it's a 2.5 to 1 to read as 2.5:1.
I found this blog showing how to do it for line slopes, but I think it's not able to work using the run:rise format.
AutoCAD Civil 3D :: Surface With Specific Slope - Calculate Cut And Fill Volume
May 25, 2013I use Civil 3D 2011 and I am new to it. I have created a natural ground surface from survey points. Now i want to create a finished surface with a specific slope in a specific direction at a specific elevation and then to calculate cut and fill volume.
I can create a flat surface at a specific elevation. How to tilt this surface to a specific slope along a specific direction.
AutoCAD Civil 3D :: Grading Slope Projection - Correct Surface To Implant Photovoltaic Structures
Jun 12, 2013I am looking for grading utility in autocad civil 3d. So, i need to smooth my projection slope to target the surface without projection steps. The objective is to correct a surface to implant photovoltaic structures.
View 3 Replies View RelatedAutoCAD Civil 3D :: Link Offset To Surface?
Oct 10, 2012When I use link offset to surface and attach on left side, still extend to right. I am targeting a slope stake line polyline that exists on both sides of the roadway, works fine on right side. Documentation indicates that a negative offset value is needed to use to the left. How do I use negative value and target a polyline?
model (1) is the result on the left
model (2) is the correct result on the right
AutoCAD Civil 3D :: Corridor Surface Ignoring Vertical Link?
Nov 6, 2013For some reason the surface created by my corridor is ignoring the vertical link on the edge of the subassembly. How can I get it to include that?
View 4 Replies View RelatedAutoCAD Civil 3D :: Point File Link To Surface Lost
Mar 18, 2013I think this should be an easy thing to do, but I am having problems figuring it out. I need to repath the location of a point file being used in a surface. My surface will not rebuild because it can't find the point file originally used. Drawing was used on a different computer system, so the point file directory is now pointed to the wrong path.
View 7 Replies View RelatedAutoCAD Civil 3D :: Create Subgrade Surface Using Base Link
Aug 21, 2013I just tried to create a subgrade surface using the base link. The surface turned out to be wrong because some of the points in the Lane Outside Super Layer Varying Width subassembly are uncoded. Everything I've looked at seems to be programming related (over my head). Do I need to download a composer for 2014? I didn't see one on the list for 2014.
View 3 Replies View RelatedAutoCAD Civil 3D :: Surface Slope Labels - Rise:Run Custom Labels?
Dec 27, 2013I am trying to create a surface rise:run slope label for our company template file. I have it set using the default values that I want. But right now the text is just 1:1...where we want it to read 1V:1H.
how I can keep the label dynamic to the surface, but put the V & H in the label after the values.?
AutoCAD Civil 3D :: Profile Geometry Editor - Slope-Slope Intercept To Place PVI
Aug 20, 2012Can you not perform a slope-slope intercept to place a PVI? Essentially holding the sta and elev of the PVI's directly before and after the PVI of interest and changing the grade in and out so that the sta and elev of the PVI of interest are changed.
View 2 Replies View RelatedAutoCAD Civil 3D :: How To Match Gutter Slope To Outside Lane Super Subassembly Slope
Mar 22, 2011Can't figure out how to match gutter slope to outside lane super subassembly slope. Have super eop targeting a feature line with elevations, but when i check section editor gutter slope doesn't match pavement slope.
Civil3D 2013
Windows 7, 64 bit
Intel i7 2600 @ 3.40Ghz
16 GB RAM
Nvidia Quadro 600
AutoCAD Civil 3D :: Shoulder Subassembly That Varies Slope In Relation To Lane Superelevation Slope
Jan 22, 2013i need a shoulder subassembly that varies slope in relation to the lane superelevation slope. i know that i can get a subassembly for the shoulder that will follow the alignment superelevation xml data but in my case i can't use it because we are just adding a shoulder to an existing road. we're not changing the superelevation of the existing road, just milling and overlaying and widening. right now i've created a profile of the outside edge of the shoulder that gives me the correct shoulder slope but whenever i change my centerline profile i have to redo the shoulder profiles which is a real time suck.
View 9 Replies View Related