I would like to change the station label format from 00+000.000 to 00,0+00.000
To move the + is easy, but how can I add the ,?
This type of station label is the standard by the Deutsche Bahn, so it's not that far-fetched.
Win7 64bit
HP z400 Workstation
ATI FirePro V4800
C3D2013
How do you Change Station Label Format from 20+00.00 to 20+00 ??
View 3 Replies View Relatedhow do you change their layer? i have been through the settings tab under "alignment", "station offset". i also right clicked on one and went through the properties.
View 4 Replies View RelatedI have a problem with some station labels I have, when I open the drawing(s) the labels display ??? instead of the station. After I manually sync the alignment in prospector, the drawing switches to the model tab with the ? now showing correctly.
View 2 Replies View RelatedIm trying to make a label that will call out pipe replacement in reference to an alignment. I know how to call out from multiple alignments, but I need multiple stations from the same alignment, such as sta xxx to sta xxx.
Windows 7 x 64 bit
NVidia Quadro 2000 Dual Monitor
6.00 GB RAM
Intel Xeon W3550 @ 3.07 GHz
Civil 3D 2013 SP 2, Civil 3D 2012 SP2, Civil 3D 2011 V3, Civil 3D 2010 V3
I have an alignment that starts at station 1+00 and runs through 20+00.
By right clicking the station labels and editing the label group, I have updated my major station increments to 200' and my minor stations (ticks only) to 100'. The problem is, I want the 200' increments to begin at my starting station (1+00), so that the labels would read 1+00, 3+00, 5+00, etc.
As it is now, the above settings make my labels read: 1+00, 2+00, 4+00, 6+00, etc.
When I am in the file with the labels everything is the proper size. When I reference this file into my sheet file everything becomes tiny. Any legitimate solution?
View 9 Replies View RelatedNew to civil 3d...I have a series of bore locations along an alignment that I need the station offset and distance. I tried POINT -> ALIGNMENT: STATION/OFFSET, and that prompts me to tell where i want the offsets to go. I want to be able to pick the center of each bore and have civil 3d tell me that information. What command do I use?
View 4 Replies View RelatedIs it possible to add a prefix to an alignment station label (ex. A 100+00.00 or B 100+00.00) in Civil 3D 2010 or later?
View 5 Replies View RelatedIs there a way to label or list a station at a specific elevation? I know how to list and label an elevation at a given station but I need to know where a specific (given) elevation is located on an alignment or profile. I don't care if this is listed or labeled on the alignment or profile, I just need to be able to get a station at a given elevation.
View 5 Replies View RelatedI am trying for last hour but cannot make this work. I have attached screen shot of a dynamic label with some text. The problem is as you add degree symbols and inch (") symbols and paratheses to the text, the leader starts to intersect the station value. I want to move the leader a little below the sta. value so the station vallue is readable. When I move the leader the text moves with it. I tried everything in edit label text option but cannot seem to fix it.
[URL]
I would like to set up an alignment station offset label that when in the dragged state, offsets the arrowhead from the actual insertion point on the alignment in any direction and distance I specify. I am preparing some plans for a water line. I am working at a 1"=200' scale so all of the blocks representing fittings are scaled up so they are legible.
In some instances, the fittings are right next to each other. If I place an alignment station offset label at the actual station and drag it away from the alignment, the arrowhead is pointing to the station but not the fitting. Is there a way to offset the arrowhead of a C3D label in dragged state other than in the direction of the leader?
I am looking to create a alignment label style within 2013 that allows me to create a label that looks somewhat like the following:
alignment 1
sta=xx+xx
alignment 2
sta=xx+xx
The label would be used at the intersection of 2 separate alignments.
I can label the superimposed profile but c3d uses the stations of main profile of profile view.
Thinking on the future.... c3D can have the ability of use superelevation values to calculate the right values of superimposed profiles ?
I've read or seen a video on this before, but don't recall fix. As you can see in the attached image that half of my station label is missing, is there a fix for this. I think I recall reading you need to include a data band strictly for positioning of profile view.
View 4 Replies View RelatedLooking for a way to label two station on one alignment in a construction note.
Civil 3D 2013 (SP1)
Dell T3500
Win 7 Pro X64
Intel Xeon 3.2 GHz
24 GB ram
NVIDIA Quadro 4000
Typically when we have station offset for a storm structure shown to center of structure. How do you handle station offset with a storm structure label for say back of curb.
View 3 Replies View RelatedI am labeling station and offsets from my alignment for curb returns and such and for some reason if the offset point is directly perpendicular from an alignment PC or PT the label can't find the alignment information. It's like there is a blind spot.
View 4 Replies View RelatedWe are trying to label the intersection points on an alignment with the following info:
Sta:
Delta Angle
LAT
LONG
We can make it work with a Northing and Easting, but there is no option for a LAT LONG under the tangent intersection labels. I tried to make an expression that would format a Northing as a LAT but it just gave me jibberish.
I was able to do it but adding a point at each PI and making a point reference text, but you then have to select a different point for each label.... which works but it is still a multi step process.
Is it possible to modify a label set to a new starting station, e.g., instead of the alignment starting at 0, change it to start at 100?
View 9 Replies View RelatedBasically I have a centerline alignment for a roadway and another alignment for a retaining wall. They both have the same bearings and a common horizontal bend point, though the wall tapers off in another direction at the end. The issue I'm having is at the common horizontal bend point, when I label my retaining wall bend point and reference the centerline I get a different centerline station than what I should be getting. It appears that when Civil3D calculates the reference station, it uses the line segment after the bend point instead of the line segment before.
Is this dependent on a C3D setting and is it possible to change this?
how to update the information? I revised the pipe alignment but the profile did not update the station. WHat steps do I need to perform?
View 1 Replies View RelatedMy dragged state leader does not display properly. The attachment runs through my first line of text. My display is set to "As Composed" I do not want the stacked text setting.
View 9 Replies View RelatedThe label associated to a grading point when is moved when is moved changes its size automatically and a leader appears. After this happen no control over the grading point and its associate label. refer to the image below.
View 1 Replies View RelatedI can't seem to get my profile start and end station labels to appear even after I checked "Label start station" and "label end station" in the profile view properties.
View 2 Replies View RelatedC3D 2012 running with 64 bit Win7 all up to date on a capable Dell Precision
I want to add the leader part to the leader that is created when I drag a Station Offset label. This would be the part in a three point leader that goes horizontal for a short distance before the label text begins, similar to how a multi-leader is created. Looks weird having the C3D labels be the only "leadered" noted be without the landing.
I am trying to create a station-offset label style that will drop the trailing zeros in the offset section - e.g. 15' instead of 15.00', but if the offset is not at a whole number, e.g. 15.01, etc. it will display the entire offset.
I created two expressions: IF(OFFSET-TRUNC(OFFSET)=0,.1/12,.00000001/12)
and this one: IF(OFFSET-TRUNC(OFFSET)!=0,.1/12,.00000001/12)
I then created two offset components, one called truncated, and one called full, and assigned the heights to match the expressions.
I have attached the file, the style is ACHD-Sta Off-Rt [copy]
C3D 2011, Win x64
I've attached two screenshots of my issue. I simply need to change my major station from 1000' interval to 500' interval. As you can see from the screen caps, I can manage to get the band details on the stations I want, through a workaround, but the vertical gridlines get all messed up.
Windows 7 x 64 bit
NVidia Quadro 2000 Dual Monitor
6.00 GB RAM
Intel Xeon W3550 @ 3.07 GHz
Civil 3D 2013 SP 2, Civil 3D 2012 SP2, Civil 3D 2011 V3, Civil 3D 2010 V3
where to change the default beginning station from 0+00 to 1+00 in my civil 3d profile template (dwt), so that the beginning station is always 1+00, unless the user changes it.
View 3 Replies View RelatedI have an alignment and have station labels. The alignment is labeled with "Major Stations" at every 100 feet. I need to change the station increment to 25 feet and have labels. I have done this although station 1+25 is still reading 1, station 1+50 is reading 1, etc. There is a precision variable somewhere, and I can't figure it out. I have played with the alignment labels style but no luck. Is there a global drawing settings somewhere that might be controlling this?
View 2 Replies View RelatedI need to export the surface lable table report into microsoft excel format.
View 5 Replies View Related