I am using Civil 3D 2010 & getting an error message when I run the command (AddNetworkPartsToProf) to add network parts to the profile.
Here is the message I get when I select a part of the pipe network to draw into the profile. "1 object was of the wrong type. All objects in the pickfirst set were filtered out, please select again".
I have a user having an issue with drawing pipe networks. When they draw the pipe, the structure is not visible. A label shows up, and the structure can be found in the prospector, but is not editable in the plan view (see attached image).
I have a feeling it may be an issue with our pipe networks parts list and pipe catalog location. We have found an issue with our install that defaluts our pipes catalog to our local drives, but our parts list were created using a network drive. Several users have had an issue creating pipe networks when this has happened. However once we switched the pipe catalog to the netowrk drive the issue was resolved.
When we changed the pipe catalog location, it did not resolve the issues.FYI - I have tried the basics (layers on/thawed, pipe structure style layers on/thawed, audit and purge).We are using Civil 3D '09.
I am using civil 3d 2012.
I have a network that I showed in a profile view and, to creat my proposed pipes network I simply copied the pipes and structures and used network split.
Now I have two networks, but when I project those pipes and structures into a profile they are not visible.
If I check the profile view properties and look at the pipe networks tab, all the pipes are shown as drawn.
If I have a pipe that spans between two profile views, is there a way to label the pipe in each profile view with only the lineal feet that is showing in that profile view?
View 4 Replies View RelatedI am using C3D 2012.
I have a storm water pipe network and a sanitary pipe network. In the profile view I am displaying both networks. My question is in the profile view the storm pipes are in "front/foreground" of the sanitary pipes. Is there a way to "trim" out the sanitary pipe profile lines where they pass behind the storm sewer.
Kind of like a display order so looking at the profile I can tell which pipe and in foreground and which are in the back ground.
I'm trying to swap one type of inlet for another. I can swap the type-13 to a type-R but when I try to swap it for a double type-13 it reverts to the single type-13. This is happening with a 7' manhole as well. I can swap a 6' for a 4' or an 8' but it will not swap to a 7', it reverts to a 6'. Is there something in the catalog for this that preventing the swap?
View 5 Replies View RelatedWe recently installed C3D2013. We were using our profile from 2012. When we tried to set the Pressure Network Catalog and then edit the Standard Parts List, we get a message that it references a catalog that can't be found. I have seen this on other posts.
I changed the profile to the out-of-the box profile, and now it will let me edit the Standard Parts List. When I drag the parts list in the _AutoCAD Civil 3D (Imperial) NCS into my original drawing, it loses the material.
What element of the profile allows it to set the Pressure Network Catalog and have it work? Does the Parts List in the template play any role in the interactivity between the Catalog and the Parts List?
Also, if I copy the Pressure Network Catalog folder from the C drive to a network drive, I again get the message that it references a catalog that can't be found. Can the catalog not be moved?
Civil 3D 2013, SP2
Settings > Pipe Network > Right Click > Edit Feature Settings > Default Profile Label Placement, gets you to this point:
Does the highlighted line only apply at the time that the label is placed? I have multiple sewers to label and I want to each set of labels at a different elevation. Changing this default will have NO effect on existing labels?
I have in front of me a survey of a small section of road (it's only 10m x10m or something). I want to be able to create a profile along the road section to demonstrate the surface level changes. I have created a network surface but Civ3D doesn't seem to able to use this type of surface to create a profile. Is there anything I can do, perhaps a way of transforming the network surface into another type of surface? Or am I going to have to manually create this profile in ACAD!
View 7 Replies View RelatedI can create labels to display stationing in a profile, but is there a way to display the coordinates in the profile instead? When I need to move my pipes I am using the station I get from the profile label and then use grip move. If I could get the N, E, I could just type it in on the Vista table.
AutoCAD Civil 3D 2012 SP4
Windows 7 (64)
Under the Settings tab in the prospector go to Pressure Network/parts list/ It allows you to do things with DIP but does not give options for PVC.
View 1 Replies View RelatedI have pipe crossings shown in my profile. Only crossings (NO PROJECTIONS). So many elipises. I want to label them. Setting the label style at the pipe network does not work (will not override whatever label style was assigned at the pipe creation). I have accepted this (although it sucks).
Now, to get around it, I go Pipe>Add Label>Add Pipe Network Label. Label type is "Entire Network Profile". When I do this, it labels not only the crossings but all projections. So I have a million labels chilling out in space, where I have no crossing.
Water main pipe network profile labels for structures do not attach to the structure properly in C3D 2014 (this same label style works fine in all previous versions of the software, through the 2013 release). The labels come into the drawing at a northing of 0 rather than attaching to the structure itself. However, if you grip edit and reset the labels, they reset to their correct attachment point. Additionally, if you attempt to grip edit the profile labels with Ortho mode on, it moves the label back to a northing of 0. I've created a new block for the structure, but that does not resolve the issue.
I've included a link to a Chronicle video that demonstrates the label behavior. [URL] .......
If I have a Crescent Road (P - shape) where the Alignment returns to itself, when i draw pipe network parts in profile, the pipe network gets drawn wrong, ie. the tie-in structure at the intersection is drawn at the wrong station.
My understanding is that the structures will get drawn at the station closest perpendicularly to the alignment, so the structure is going to the end station as opposed to the beginning simply because the end segment of the alignment is closer.
Is there any way to make a structure use a different perpendicular station (without shortening the alignment)?I don't want to move alignment or structure.
I am having problems with the display of my structures in a profile view. Previously, when I change the inverts of the pipes connected to my structure it would automatically adjust the bottom (sump) of the box invert to match my lowest pipe. However, for some reason it has stopped doing it and is now displaying the sump invert incorrectly. I have my style set to "Display as a Boundary". I have edited the structure sump to be by both elevation and depth, but it does not update the sump elevation. I have tried to grip edit the sump but it seems to be locked at a certain elevation. I have a profile with 10+ structures and they are all at multiple depths. I realize there are minimum depths allowed by the structure, but I have exceeded the minimum depths in all cases. Attached is an image that depicts my problem. No matter what I do to change the depth it stays locked at a certain elevation.
Civil 3D 2011, SP1
I am using C3D 2012. I have a pipe network catalog located on our office network server. I have a pipe size shown as 15" that is incorrect, it should read and label the pipe as 16" (see attached image). I don't know a lot of the workings how to edit this from 15 to 16 inch and what I need to do to get it correct for the other C3D users in the office.
View 1 Replies View RelatedI was wondering if there exists a library for pipe network parts for items such as a standard type 1 catch basin that I can add to the existing autocad pipe network parts library. Basically I'm trying to find a shortcut so that I don't have to build all of the catch basins that I need.
View 3 Replies View RelatedWe have a big piping job coming up and as Civil3d still lacks some of the labelling abilities we want in the profile view bands. I am updating some old vba that adds a profile line of the invert of a pipe network to a profile view effectively tracing along the bottom of the network like I know a lot of people do by hand.
My original code works on assuming that the start and end structure are at the start and end of the alignment in the revised code I want to allow for situations where this is not the case.
Leading to my question is there and easy way to find the distance a profile view part is drawn along the parent alignment or do I have look at writing my own function possibly extracting a polyline from the alignment and finding the distance using intersectionwith and distancefrom functions with the structure.
I'm trying to add assign a Pipe Network to a profile view Band in Civil 3D 2011. I was using COM to add profiles to bands because I couldn't figure out how to do it in .NET. But when it comes to pipe networks I don't see how you can do that with COM. How the .NET implementation is supposed to work? Here's the code I have that works for COM, except for the pipe networks. I essentially need to assign the correct pipe network to the band.
public static void AddProfileToBand(this ProfileView profileView, ObjectId profObjId, List<BandItemInfo> bandStyleInfosFromSet, ObjectId profileBandSetId){
using (Transaction tr = Application.DocumentManager.MdiActiveDocument.TransactionManager.StartTransaction())
[code]....
When creating my plan set, I need to data reference pipe networks into other drawings than that in which they were designed to show crossings in profile views or to separate out profiles into managable drawings. When I do this, if I have swapped a type-13 inlet for a 10' type R inlet or something during design, the data referenced pipe network will replace the 10' type R with a default inlet. Also if I have swapped a proposed 30" pipe for an existing 30" that have different styles, the data referenced pipe network will revert back to the proposed 30" pipe. how to make a data referenced pipe network reflect what is currently in the design drawing?
View 9 Replies View RelatedIn plan production, I have created the sheets (plan & profile) as a seperate drawing.
when I open the sheets, the pipe network profile labels are missing in model & paper space. (attachment 01)
I tried to on/off the annotation visibility tabs in the lower right corner (attachement 03)
Note: While creating the sheets, I select the tabs for pipe network & copy pipe network labels to destination drawings (attachment 02).
I am using Civil 3D 2013. I work in an office where we have a few different flavors of Autocad (LT, MEP, regular vanilla AutoCAD etc...) and versions (2010 LT, 2011, 2012, 2013).
For the most part there isn't much inter-office drawing coordinate that has to happen, but there is the occasional project where multiple disciplines (Structural, Mechanical and Civil Site) have to share drawings.
The specific problem I am having is when I share my 2013 Civil 3D drawing with a user using 2011 MEP. He gets the typical rectangle for the proxy objects (in my case, my pipe networks for sanitary and storm drain). We've tried downloading and installing various object enablers, but there doesn't seem to be one for a 2013 to 2011 scenario. So I setup my parts to be on layers that he can just turn off. HOWEVER... the actual pipe network (not the structures, parts, labels etc... the network itself) ends up on layer 0. For this specific project, I do the old (ssget "x" '((8 . "0")) search to select all objects on layer 0, add those objects to a selection set (pselect), then in my modify objects dialog I filter for pipe networks, then change the layer to something other then 0.
While this is a workaround that works for me, what I really want to know is if there is a way that I can change the default layer that the network (again, not pipes, structures or text, the actual network) so I don't have to use the workaround. Any thoughts?
P.S. It's killing me that I had to create a new Autodesk login and now all my AutoCAD "street cred" is lost
"The source of expertise is not in the memorization of the minute details of a subject but in the thorough understanding of the fundamental concepts on which it is based."
I am trying to transfer my profile to another computer on our network. I exported mine to the network. (.arg file) When I imported this to the new computer it did not include the toolbars that I have set up on the original computer. What do I need to do so they will be included?
View 3 Replies View RelatedI am using Autocad 2008. I lost all my icons when opened a drawing after disconnected my workstation off my domain network and trying to use it locally in my local drive.
in order words, How can I copy my network/server profile into my local drive so that I can run Autocad from my local drive ?(My Autocad Software is loaded in my local drive).
I have an alignment label that I normally use to show the PVI's of a profile in the plan view.
This is a little unusual, but in a specific case I wanted to design my profile at one alignment, but show it at another. I designed my swale profile in the pathway profile view and then superimposed the swale profile on the swale profile view. I then went back to the swale alignment to add these labels.
It's a no-go AFAICT. The only profile available for me to select for these labels is the original ground profile from the surface.
I'm working with a structure profile label style and it seems like the only way to anchor the position of the label is based on offsets from the structure itself... Any way to position the label based on the top of the profile view, so that I could make all of my labels horizontally aligned above the profile view?
View 9 Replies View RelatedIm creating a Profile Bandset and would like to have multiple surface/profile elevations shown, ie: EG, FG, Back of Curb and Back of walk. While creating this bandset I see that the text component editor properties only has code for profile 1 elevation and profile 2 elevation in the properties area, which the code for this looks like below.
<[Profile1 Elevation(Uft|P2|RN|Sn|OF|AP)]>
<[Profile2 Elevation(Uft|P3|RN|AP|Sn|OF)]>
Ive tried to write my own code using the profile 2 as an example but it doesnt seem to work as a 3rd surface/profile and only seems to mimic the profile 2 elevation when placed in the band
My questions are as follows
1) does Civil 3d only allow 2 surface elevations in any band set? if it does allow more profiles/surface elevations what am i missing to create it?
2) if Civil 3d does alow for multiple surfaces to be shown in the band set how do i get the text component editor to supply the extra profile elevation codes? or would i need to create from scratch
3) if i need to write the code from scratch does any listing of the codes and meanings of each code ie what does RN, Uft, Sn and so forth do and mean .
I have a group of profiles in a drawing and I want to change how one of the profiles is displayed through the profile view style manager, but I do not want to change how all of the profiles look. Is there a way to change the way a single profile looks without changing all of them?
View 2 Replies View RelatedI have a profile showing proposed storm sewer, existing sanitary, rock surface, existing surface, and proposed profile. Today for some reason the proposed profile and labels, and the existing surface are not showing on the profile and I'm not sure what has changed or how to get them back.
View 3 Replies View RelatedI am working C3D 2012. I have a proposed alignment and profile design by another firm that I had to tranfer into C3D. I had no problem getting the horizontal alignment to display from a text file. I tried to do the same with the profile by using the 'create a text file and create the profile from file' command. I got the POB, PI's, and POE to display. I then defined the VC. I wanted to verifiy that the profile was indeed accurate compared to what we were provided. So I tried to execute a profile report PVI Station and Curve Report - I keep getting an error that "No FG profiles in dwg".
I know the Proposed profile is indeed set to proposed in the properties. I have noticed that the icon next to the profile I create from the text file is different than the profiles created from scratch.
Is there a way to convert this profile to be recognized as a FG profile?
Intel Core i5-2500K CPU @ 3.30 GHz
8.00 GB
64-bit
I try to make curb return profile without profile view like a intersect command.
I was make curb return alignment but I can not find profile command without profile view.