Starting Installations with Setup view screen the following error message:
The system cannot open the device or file specified.
C:UsersNombreAppDatalocalTemp\_AI4662.tempx86en-usComponentsadr2012SetupDesignReview2012.msi
I am unable to install AutoCad LT 2013 on my Windows 7 x64 system. Everytime I try to install I get the error message:
"The system cannot open the device or file specified.
C:UsersEricAppDataLocalTemp\_AI194B.tmpx86en-usComponentsadr2013SetupDesignReview2013.msi."
I can go to that folder and that file is there. However, if I try to run that file it then gives me errors about other missing files, that are not in that folder.
I have tried this with Multiple Logins, including the Adminstrator. I have also, completely wiped out the system and reinstalled Windows 7 from scratch.
I have set the UAC to the lowest level.I have also tried another DVD, and tried copying the files to the machine. No matter what I try I get this same message.One other thing, this is the 2013 Upgrade.
I install AutoCAD LT 2013 when I click install after few minute it show this error message.
The system cannot open the device or file specified. (Please see attached file)
With the command window displayed at the bottom of the screen, everything slows down. The cursor momentarily freezes and it takes a second or two for commands to be fulfilled. Also, the command window is about 7 lines high; in the past, I have shrunk it to maybe 3 or 4 lines but I cannot shrink this wndow.
Then, when I push control-9 and the window disappears, everything speeds up to normal!
I tried turning off my internet connection and my McAfee Viruscan as well. Running without the command window makes it hard to draft. Since I type shortcuts, I figure I must have hit the wrong key and unleashed something unspeakably terrible.
I am running AutoCAD version 10 on my PC, with Windows XP Professional.
Halfway installing PSP Prox4 from my disc or via the web, error message comes up: "The system can not find the device specified" and "Your system has not been modified".I have the latest drivers and DirectX installed.
View 2 Replies View RelatedHad a system crash. I had Norton 360 using a slave HD as my automatic backup source. To reinstall windows, master HD was overwritten. I thenfound out Norton 360 didn't save my autocad files to the slave HD. Their definition of "other files" didn't cover dwg files unless you did an extremely detailed setup process, which, was not in the Norton instructions. Anyways, local computer service was able to recover about 60% of the "lost" autocad files.
Of those recovered files, about 60% will not open up. Only get a message "not a valid file" The file details show its an autocad file, its size, and the last date of revison.
in autocad 2010 & 2009 certain commands are not working, but if we change certain system variable values, it will work. but the problem is each time when we open the file, we have to change that system variable.
View 2 Replies View Related1 How do I determine what coordinate system a drawing I have received has been prepared in?
2 I know how to export drawings to a .shp file but how can I export this drawing to a .shp file and ensure that coordinate system is maintained or otherwise changed for use in Arch GIS?
I have successfully exported the .shp file geometry previously but the cordinates system doesn't seem to match ARCGIS data sets. I am trying to establish is this an Autocad or ArchGis issue I suppose.
My current task is this: Open xml file from file system (later this will be from a remote service), parse the xml, display content from xml to user. There are further steps after this, but I am stuck at the first step itself. What illustrator plugin sdk APIs allow me to parse xml and create a dom out of it?
Version: Illustrator CS 5.1
As an engineering company we have started to convert hundreds of our drawings from AutoCAD to PDF using a batch utility.
However every file that is converted into a PDF file is opened by a PDF Viewer. We want to prevent this.
I opened my *.pc3 file and removed the check from the appropriate box. See below
I press OK, then save the file and close. However when I reopen the file, I see the box for Openining in PDF Viewer has been rechecked. No matter what I do, I cannot permanently remove the check from this box.
When I have 2 files open, one minimized and the other visible on the screen, when I quit the file showing on the screen and then open the one that was minimized, it comes up w/a blank black screen. There is no way I have found to get the info in the file to display.
Then, if I save the blank screenof previously minimized file, close it then reopen it the info is back on screen with changes made to the file intact.
In autoCAD tools I am using Device ID to mark my receptacles GFI, WP, and Ect. I am using Light ID to mark my lighting fixtures. The problem is the labels do not match my current text style. These tags also do not work like room tags and other tags I have searched to resolve this issue. The command these tools are grabbing is AECscheduletag. Is there a way to change the text style and size for these tags.
View 3 Replies View RelatedWe're trying to use vtablet with ACAD 2012LT and a GTCO Rollup III 3648 on Com1, 32-bit Win7 (32-bit driver) and are having a bit of trouble with the configuration.The problem is that ACAD seems to only half-recognize it.
When we try to change the pointing device to "wintab compatible digitizer", the change won't "stick" - but I don't see an error message in the status line. The "apply" button simply continues to stay grayed out and clicking on "ok" doesn't make ACAD save the change. Thus since the pointing device remains a mouse, when we try to turn the tablet on, we get an error message that says "your pointing device cannot be used as a tablet".
However, we can move the tablet's stylus and it moves the cursor. We can also draw a line in ACAD but can't calibrate (since calibrate never becomes an option since we can't turn the tablet on inside ACAD).
Yes, UAC is off. Yes the digitizer does seem to be sending regular packets. Yes the digitizer shows up in device manager as a MS Serial Ballpoint (the mouse uses USB). They both move the cursor seemingly without conflict (there is no jerkiness).
VS Pro x3 - Trying to do voice over on a project and get the above code. I opened a blank project to test and voice over works OK?
View 2 Replies View Related I have X4 Pro, X5 and X6 Ultimate installed on my computer; as well as, a few older versions of ULead software. I keeping getting this message: "device error. Cannot open the wave-in device" every time I try to use the microphone option in X6 to try and narrate my video.
The microphone option works fine in X5...
The trouble is I am using the track motion option from X6 in my video, so I cannot open the video in X5. Is it some sort of driver problem, or is there a corrupt file that needs replacing etc...
When I connect my camera to the computer, Lr does not automatically open. I have gone to the Preferances interface to ensure Show import dialog when memory card is connected is checked.
Lr does not even show up in the Auto Play pop up window.
quick back ground - Windows 7 64 Bit - Autocad 2010 installed - IE 8 32 / 64bit - Lotus Notes 8.5
Our DWG files are stored in a shared folder, and we use a Lotus Notes DataBase to browse for drawings as you can put information with the DB Entry.
When you click Open drawing IE 8 pops up but the window is blank. PDF's open fine in IE 8.
why the dwg drawings are blank?
I'm working in AutoCAd 2012. I tried to open a set of working drawings that i've been working on. The file won't open. So far, with no success, I've tried:
a) renaming the .bak file as a dwg and opening it.
b) inserting the file in a new drawing
c) inserting the file as an xref in the new drawing
d) using recover to recover and fix the file
e) using recover to open the backup file
f) using the partial open command to open the file.
I use auto cad 2010.In my computer .dwg file is deleted but .bak is in my computer but when i rename the .bak file to .dwg file but it not open in auto cad 2010.
View 5 Replies View RelatedI'm having a problem that my file dialog box won't open when I go to open, new or save as. When I hit open, new or save as the command bar wants you to type the file name. My co-worker told me to type CMDDIA and change it to 1. But that didn't work for my error. How to fix my AutoCAD issue. I attached a .jpg of what the command bar looks like when I hit the open button.
View 2 Replies View RelatedI downloaded a model of guitar as .dxf file from here. But somehow it opens like the image attached below. I've changed the visual style to realistic but it seems, its all just lines and no solid body.
View 4 Replies View RelatedThe file autocad 2010 (dwg) that I've been working for ages doesn't open. It starts loading but then get stuk on 96%. I tried to recover it and no errors are detected.
View 9 Replies View RelatedDoes a file on AutoCAD 2014 open on AutoCAD 2010?
View 4 Replies View Relatedwe have a new lab in our district with Autocad 2010 64-bit version installed on HP Compaq 8022 Elite SFF computers. There is 4 GB memory on the computers and a Quadro 400 graphics card. Autocad and Windows 7 64-bit have both been updated to the latest versions. The Autocad application locks up almost every time someone chooses the new document icon, or when they try to 'save as'. Sometimes when they choose to open a new document first, close that dialogue box, then try to choose the new document icon it works ok. But, for the most part, the application is unuesable. Some possible solutions we found online that don't work are to not use the Aero themes (we don't) and to not use Norton AV (we don't).
View 9 Replies View RelatedI installed AutoCAD on my pc with windows 7 and to complete the installation I had to change the registry file EULA from 0 to 1. Now it works but when I try to open an existing file it crashes.
View 1 Replies View RelatedI am having issues with my computer completely freezing while performing a File, Open process. I'm in drawing 1, I save it, then go to open drawing 2. Drawing 1 will save, the open file window pops up. With me so far? While navigating through the file directory tree, my computer freezes. I do not chose a file that freezes during opening. It is during the process of getting to the folder drawing 2 resides in, and then it freezes. This happens to me multiple times a day. Ctrl +Alt+Delete will not work. I have tried letting my computer sit, as you would with a program not responding, and it doesn't unfreeze. The only option I am left with is a hard reboot. The only other program I have running is my MS Outlook.
I have been back and forth with our IT person, and because he can't replicate the problem (after trying one file open), he can't figure it out, or doesn't want to.
I am running AutoCad 2012 with a Dell Precision T3500, 2.13ghz, intell xenon E5506 processor, and 4gb of RAM. After looking at the system requirements, and reading that 2012 needs a 3.0 or higher processor, could this be the route of my issue?
I used to be able to save as and browse to the file where I want to sane or open a file
Now I get a dialog box where I can only save to the default location or manually enter the path and file name
Same with opening a file - I go file open and it is gives a path to the last file I used. There is option to browse - how I get this back to the normal function of open/save by browsing?
I am making an excel spreadsheet that has a list of all the drawings we have on file, an inventory list per say. I have all of the drawings hyperlinked.
View 3 Replies View RelatedUsing AutoCAD 2012 SP2 on WinXP.
On a file server, when a folder permission has been set to "deny delete" we cannot navigate to that folder in the open file dialog box.
keep getting program not responding message when I try to open a drawing.
View 9 Replies View RelatedIs there any way to disable the "would you like to open the file read only?" alert window when I open a read only file?
Software: Inventor Series 2011 SP1 x64
OS: Vista Business x64
CPU: E6400
RAM: 2*2Gb GeIL
VGA: Quadro FX 550
