I'm not 100% sure that this is the place to post this question, but support for Civil View is a bit sparse. I'm basically trying to import an FPZ file that someone has exported out of their Vissim file. I'm using the Civil View utility in Max Design 2012 and it works really well for the most part. When I get my vehicle data imported, the cars are too close together (overlapping by a lot). I double checked to make sure the file was being exported in feet and I have civil view (and max) set to feet. The cars blocks are sized correctly . . . they are just way to close to one another.
I thought I would try to set the civil view importer to meters (as it LOOKS like a units issue) but I can't seem to find that menu anymore. It used to open up when I opened up Max.
I'm still having performance issues in 2012. Thought that going 64bit 8gb ram. It seems like anytime I do anything in C3D, network traffic is generated, and I'm dead in the water until the traffic terminates.
network traffic generated with moving a section view twice. While on the "plateau", I have a busy cursor. As soon as the traffic drops down, I can start working again. Why would moving a section view generate network traffic?
i have created a data band in profile view that should show a created profiles elevation, but some of the the data fields are missing irregulary. Also in the data band that shoud show the diferenece betven the tow profiles - EG and the new profile the data is missing. The EG profiles data and the surface are ok all is shown.
I found super elevation labeling for profile, but not for alignment in plan view. Is there a way to label alignment, f.x. in critical points of super elevation automatically?
I want to show the information on the attached document in the drawing also attached in civl 3d. The final outcome layout of band data i want is titled wanted outcome and the drawing is preliminary vertical long section.
I have many section views of a road where I want to calculate ground volumes. I have a curb in a section view and I want that Civil showed me just an elevation at the top of the curb and at the top of the road cover. Is it possible to do that? And also distances: I want that Civil just show me a distance from the center of a road to a curb and from a curb to the edge of the road.
I need to identify these Fonts, used in traffic signs – as well as the Font used in the quotes measurements below. "What The Font" could not find out them.
I am currently in the process of doing some traffic management drawings and need some road signs, but mainly im after some free cone software apparently. You can get some really good software, free if possible if not then the cheapest available. This is for autocad 2008.
I have a master shape file that contains parcel ID, owner, tax info., etc. I have another file ( access 2003 -open to better file format suggestions-) which contains parcel ID and a "yes" or " no" entry for whether or not the parcel needs a new water meter. All I want to do is add the water meter information into the other shape file. This would create one shape file with one table with all the information that I need.
Ultimately I will use the information to do a map query and find out spatially where i need new water meters.
Right now i have the master shape file connected though the “Connect to Data” feature. I also have the new data added to the drawing though the Data sources------>attach under the “Map Explorer” Task pane. I attached access file (ver. 2003 .mdb) which has two columns “Parcel ID” and “Meter”.
I right click on the shape file under the display manager and select”Create a Join;” however my water meter table is not listed as an option. Will this not work?
Plan B - I tried to Create and connect to the access file as an ODBC connection. Followed this guy’s directions to a T [URL]. But when i populate my table under the fdo connection the column headings exist ( “parcel ID” and “Meter”) but the actual data is missing. Am I missing something important?
Note: I am running c3d 2012 on a Win 7 64 Bit machine. I also removed office 32 bit apps and installed 64 bit apps to see if that would solve the problem. No go.
say you make some parcels in your project with custom data fields like: id_no, permit_no, acres_served etc. you attach an agency provided shape file via an fdo connection that has many fields of information like above.
when you right click on your parcel and do parcel properties you get a tab that lets you input the custom parcel data.
lets say you print an fdo map label showing, say, the id_no, provided in the shape file. Then in your custom parcel properties for id_no you type that in.
is there a way to make an expression to put in the other custom parcel properties that will read, say, the permit_no(id_no) from the fdo like and put that information in the custom parcel property field?
I'm having problems getting super elevation data to transfer to different drawings by means of an alignment data shortcut. I know alignments hold the super elevation data so I've gone into my alignments data shortcut, input my super elevation data, saved and closed. Now when I open my finished grade drawing, reference in my alignment and profiles, then create a corridor from that information, my super elevation didn't transfer with the reference.
I pulled cross sections and it appears is has no clue there is any super elevation data. Also, I tried bringing it directly into the drawing I'm doing my corridors in and it erred saying I must be in the parent alignment drawing. Data shortcuts are pretty much useless to me if super elevation data doesn't transfer.
64 bit Windows 7 Intel Xeon (R) @2.8GHz 6.00GB Ram Civil 3D 2012 Civil 3D 2012 Intel(R) Xeon W3530 @ 2.80GHz 6.00GB Ram Windows 7 Professional
I've just installed Civil3D, 64-bit on windows 7(running on bootcamp) and am trying to insert a georeferenced raster image but have encountered some issues.
1. "Home tab>>Data panel>>>insert An Image" - The data panel is missing and it's also not found in "customize palettes"
2. Trying the data connect route does not work either: Display manager>>>Data>>>Connect To Data - There is no 'Data' option and I cannot connect to Data.
I have an Excel spreadsheet I am testing to see how to edit table data in Map 3D and see the changes back in Excel. I have created the .udl file from my Excel file, which AutoCAD stores way down in the Data Links folder. I attach the .udl file as a Data Source. It shows the named range and I can view the table but it is always Read Only. I checked the Access permissions under Properties and none of the boxes were checked. So I checked ReadWrite but I still can't edit the table.
Then I tried just attaching it as an FDO provider. It links and displays the table just fine, but when I perform an edit (which it allows), the whole program crashes out without a single warning. Like I never had Map open.
This may be a Windows 7 permissions thing but since Map won't let me change the folder location where I save the .udl file, I can't test this out by putting it in a folder I know I have full access to.
I was wondering if after drawing an alignment, creating a profile, and profile view, is there a way I can mark items along the alignment so they could show up in the profile view. I am laying out a pipeline and want to have the profile display a marker for items such as tees, elbows, reducers and other items. The marker I would like to use will be something like the vertical style grade break markers.
Also on a side note, as each of these items will have a different name, is there a way that I can add these markers and then have each one with a unique name?
1. I had trouble with profile view of the alignment line shown. What step am i missing? Are there things that is turned off?
2. How can I best come up with the right volume to fill.
3. Do I need to learn the grading tools? or could i get buy with a section profile from the alignment. ( it is not even an alignment yet)
4. How to I render a rock fill in this cave-in.
The attached aerial image , has survey or cogo points that are imported to surface, to become surface points. . So I wanted to create a surface profile below and an outline of fill above it. Iideally the side profile would look like a trapezoid, where the base is the surface proile and top would be the design embankment.
But the reason , a surveying crew went down and took shots at the shoreline and a couple shots around the cave-in walls (higher elevation on the cave-in wall cannot be surveyed, although I coud have used a laser , did not) is so that a more accurate volume of the cave in can be obtained. I tried to label how far the road edge is from edge of the cave-in . Norice the higher elevations are the top edge around the cave in area.
The ouline for the embankment will be a mild slope then breaks to a more steep slope. like 4 :1 , then 1.5:1
I created 8 points (4 locations with 2 depths in each location) in the DWG of my AutoCAD Civil 3D 2013 project. I grouped these 8 points into 2 Point Groups: Point Group 1-high depth has Points #1, #3, #5, #7, and Point Group 2-low depth has #2, #4, #6, #8. I changed the 2D Wireframe to 3D Wireframe and on TOP view I saw Point Group 1 is on the top of Point Group 2 (because the 2 Point Groups have the same values of X- and Y-coordinates with different Z(elevation) value - see the first attached file. How can I change the TOP view to the TOP-FRONT view by using some Command to get this fixed TOP-Front view thar has the good separation of the 2 depths as shown in the second attached file?
I have been creating directly the DWG of AutoCAD Civil 3D 2013 for a couple of months.I created a project for the 8 points (4 locations with 2 depths in each location - i. e. same XY-coordinates, but different Z) And I just cannot separate the 2 "depth" points of the "same XY-coordinates" location in the 3D Wireframe by using the 3D Rotation Cube. I wonder I should start the C3D 2013 with choosing the right Template, configuring proper Viewports and creating suitable View Frames. I don't know what Template is right for my project of the 2 "depth" points of the same location in the 3D Wireframe of C3D 2013 - see the attached file. what Template (.dwt) is right for my project, how to cofigure 2 or 3 Viewports, and create the View Frames.
I was given a horizontal centerline of a 5 mile bike path. We have to stake all the even stationing every 50 feet and all the VPC's and VPT's with vertical elevation. I have created the horizontal profile and also the vertical profile including all the vertical curve information. Is there an easy way to incorporate the elevation information back into the plan view so I can create points that carry x,y & z points that I can transfer out of autocad as a .txt file so we can upload it on our gps equipment?
Is there a way to easily add an object from a profile view to a plan view? I have developed a pipeline profile that has high and low points and I would like to show these points on the plan views.
This is an AutoCAD 2011 related question about being unable to see under properties objects that I have attached to polylines in AutoCAD Map3D.
I have created an map3d .dwg that the polylines and points have attributes attached (objects). However, when I access the same file in plain AutoCAD nothing appears under properties.
Is is a format, import settings tweak or simply it can not be done?
I'm working on an edit, which is in video mode. Now I have to include OpenEXR material, which is in linear mode. How can I combine the two and still have the correct color?
I can set it in view mode to linear, but then all my video shows as linear too, plus, as soon as I leave the view mode, it all goes back to video, and my EXR's are too dark then..... what can I do?
Smoke 2012 SAP2 SP4 and Smoke 2013 SP2 (Smoke Classic Keyboard Shortcuts) Mac Pro 4,1 OS X 10.6.7 12 GB RAM NVIDIA Quadro 4000 14 TB RAID (Areca)
I'm attaching data to objects (attached data) and I'm unable to get the table option to open in a new window. I tried Field and the value is already set to 1. I'm using Map 3D 2012 .
Background: Our company has decided to switch from drafting in AutoCAD to Inventor (which we already use to model) and we have started looking at making our templates intuitive using iProperties, parameters, and functions to reduce manual entry of part information in turn to reduce human error. None of us have any experience coding besides a bit of LISP.
Problem: Perhaps it is a pipe dream, but one thing I would really like resolved is we have no connection between the Parts list information (specifically item number and quantity) on the assembly sheet and the part detail on another sheet. Our custom part detail title block pulls the material information and "Inventory Part Number" from custom iProperties we have set up at the part level, but we still need to reference the parts list in the other sheet and then manually enter the item number and quantity. Is there a way to use the "Inventory Part Number" property (which shows up in the parts list on a different sheet) to populate our custom block?
A lot of pictures of my collection do have GPS-data in EXIF-header. Sometimes they are shown on the world-map, sometimes not. In list-view they are never shown. The list-view knows only locations, which are matched with PSE.
The EXIF-input was made by two different tools (Holux GPS Software and Geosetter 3.4.16).
How can I get the list-view for the saved files without using PSE adding location?
CIvil 3D 2013 / My drawing opens in layout view and all model objects are appropriately coloured by layer. If I hit plot at this point, my colour dependent .ctb file works fine. However, once I swtich to model view, all my linework turns white and if I switch back to Layout view it remains white and plots each line with the weight assigned to the colour white.
I imported Google earth surface (at eye alt 600m) to civil 3d 2012 and created an alignment of length 181m.
When I exported same alignment to Google earth , it showed the length as 190m ( the difference increases with increase in length of alignment) And also the profile view of the alignment in the Civil D & Google earth varies.
