Certain exterior walls ghost out / disappear in plan when hosting a split face. This doesn't happen on all walls, and it suddenly appears on walls that were performing fine.
View 5 RepliesI drew some internal walls before adding a floor slab. After adding the floor slab the walls disappeared in plan. I can see them in 3D, in the correct place, but not in plan.
The floor slab is in the right position. To fix the problem I redrew them all, but why did they disappear and how do I prevent it from happening again?
Is it possible to design a wall where the core boundary lines fall in the middle of a wall layer?
Case in point is a complex wall with an 8" foundation wall that follows a building line along its exterior face. Above that is 3'-6" of stone veneer/airspace/sheathing/6" stud/drywall. Above that is EIFS/sheathing/6" stud/drywall.
The design calls for an insulation gap between the slab and the foundation and for the top of the wall to be 6" above the first floor level. The 6" metal stud thus overhangs the top of the foundation wall by 1" on the interior side.
Ideally the floor would be flush and core would simply follow the studs but the building lines (controlled by the grid) control the placement of the foundation wall and no part of the upper wall lines up with the foundation wall. Even worse the exterior finish falls 1/2" inside the exterior of the wall below and there should be no line drawn there.
AutoCAD 2010
AutoCAD LT 2013
Revit Architecture LT 2013
What Revit 2012 setting makes walls and floors disappear when rendering is selected?
I have a Revit 8.1 project that renderes the model just fine. When I import it into Revit 2010 it also remders the model but I have to reassign the custom finishes. But when I upgrade it to 2012 and render - the walls and floors are suddenly missing!
See attachment.
I have inserted a recess paper towel dispenser into an interior wall. Then a 1/8" tile wall was added in front of the hosting interior wall. The opening for the recess dispenser only cut into the interior hosting wall, not the tile wall. I tried joining the two walls, but it didn't seems to have any effect. Is there any reason why the walls won't join?
View 4 Replies View RelatedIs it possible to host a central file in Autodesk and use it for worksharing?
View 2 Replies View RelatedI want to turn my in-place mass walls (sloped or helical) to structural walls but i don't know how to do it. I'm able to do the walls but when i switch it to the analytical view the wall doesn't appear because it's not structural. It's there a way to do in-place mass structural walls.
View 1 Replies View RelatedThis is an emergency nesecito deliver this project on Tuesday, look what happens When I use the merge is desaparesen extruded or portions of the face
View 1 Replies View RelatedI cannot seem to find out when and where it's ocuring. I took measurements of a large room and modeled it in Autocad 2014. The solids I used are rather simple, mostly just boxes with some boolean unions and substractions here and there. I then took pictures of every wall, perspective-corrected them, imported each of them to Autocad as material, assigned the real size to the picture material and applied those materials to the corresponding wall faces. Planar mapping proved to be adequate in all cases and mostly mapped correctly on the first go.
The project was completed and saved. To my horror most of the material mappings had just gone the next time I opened the project. It was just as if I had never applied any material mapping or texture to the faces.
After partially appliying the damned material mappings and materials (textures) again I tried to determine under what circumstances the mappings get lost. Its not allways the same walls. The bug seems to occur randomly on various geometry and at various times. Sometimes the mappings get lost after opening the project, sometimes the get lost on the fly when isolating (hiding) geometry. There is no way I can get the room to look as I want it to look as there will allways be some wall that has become default-grey again, randomly (either while working or after opening up the project again).
I really expect Autocad to be rock solid after so many program versions. Did I do something wrong? How would you go about applying textures of inividual walls to wall-faces? Or is Autocad just crap regarding heavy use of textures because that is not the average use-case?
I am currently using Maya 2012 Student Version and am having trouble when extruding edges. When I click 'extrude' many of my polys disappear. I will attach some screen shots.
View 1 Replies View RelatedIm supposed to connect them like they're displayed in the picture. I did both of them separately but i just did all four to show how i want them. Im supposed to connect those two but when i press enter when im done, it disappears. Then use the insert edge loop tool to make the neck line smaller.
Both Pictures are the same. The second one just has backface cullin under display
i'm trying to use the wire tool deformer to sculpt some mouth shapes on my character but when i turn the wire tool on the faces of my mesh around the mouth area dissapear,I can still see the wireframe but the faces dissapear, I tried to turn down the dropoff distance attribute but to no avail.
View 6 Replies View RelatedI'm at my wits end trying to cut a wall with a void. I want to chamfer the corners of a wall, but I can't get even a basic void to cut from a wall. I get the error : "This Mass has no solid geometry for its Void Forms to cut. They must be deleted, or solid geometry added and cut." They clearly intersect, what am I doing wrong?
View 2 Replies View RelatedHow do you tag the rooms that are not fully enclosed by the walls?
View 1 Replies View RelatedWhy Revit 2013 when the walls are installed on some laptops is clearly visible.
View 1 Replies View RelatedThere are certain walls I just can't fillet, what's the reason of it? See attached pict.
View 1 Replies View RelatedI am currently doing an MEP project and I am tidying up the model at present. I am having problems attaching the walls to the roofs. There could be a simple solution but I haven't found it yet !
I have tried attaching top base etc. but its not working. I only seem to be able to select one side of the roof when selecting where to attach the walls. I have attached 3d pics showing the walls that are extruding & also one of the walls that I am trying to attach.
Just what the title says. Walls dont appear when drawing in plan view but appear in the 3d view. how come??
View 1 Replies View Relatedusing zoom wheel on mouse, how do i enable passing through walls, instead of continuing to zoom further and further in on walls
View 1 Replies View RelatedIs there a way to prevent walls from joining?
View 1 Replies View Relatedwhy my existing walls show up fine in my sheet but don't plot to .pdf. I have the view range settings set correctly and all other sheets plot fine.
I thought maybe the roof transparency was the issue but Revit is usually pretty much a WYSIWYG plotting operation and the walls are displaying in the sheet file. Haven't tried plotting to a plotter but it doesn't matter. I need to plot .pdf's.
How do you join a square wall to a slanted roof so that the walls are not sticking out of the roof.
View 1 Replies View RelatedHow to bridge the gap at the intersection of two types of wall. I’m wondering which “function” settings are required such that the intersection between two types of all walls (30 cm and 10cm) produce solid line.
View 2 Replies View RelatedDo I have to use the Stack Walls family in order to have my walls line up on top of each other between the levels? My walls are all slightly off in 3D view and look messy..
View 3 Replies View Relatedreinstalled revit and when i pick wall I can't choose generic walls.
View 2 Replies View RelatedIn my 3D View my walls disappear when I de-select the structural box. Although drawn as regular walls they are store front panels so carry no load other than their own weight. My Visibility Graphics dialog box seems to have limited options for this. Am I missing something? How do I get them to re-appear in my 3D View for rendering without switching them to a structural wall?
View 2 Replies View RelatedHow do you un-join walls so you can move one selection set without impacting the other?
View 2 Replies View RelatedI have one wall (basic wall) where !'ve edited to profile to have a large rectagle omitted. I have a second wall (curtain wall) that needs to occupy that space with a 1/2" gap on either side and a 1" gap along the top. I can maintain the gap along the top, but when the gaps along the sides shrinks below 1", the walls meet and the gap is reduced to zero. I've tried making the internal wall into a group, but whenever the outer wall's profile is edited to within 1/2", And I click the Finish button, the interior wall (inside the group) extends to meet it. Automatically Embed is turned off for the curtain wall. I've tried locked dimensions, but that didn't seem to work.
How I can maintain the gap without the walls closing?
I'm making a pool and i wanted to round the corners to make it seem more real. Is there a way to do a sort of "fillet" on the corners of the walls to make them round?
View 3 Replies View RelatedNeed to make a wall with varying height. For example, 3000mm at one end and 4000mm at the other. The result would be a sloped ceiling and roof. Should I make a 'mass' and attach a wall to it or is there a way to vary the height of an existing wall?
View 2 Replies View Relatedhow to have different colors for different wall faces? Like all have a plaster finish on the external side, but the colors are different, but when I try to change the color of the external finish, it changes it for all the walls.
View 5 Replies View Related